RT5350F 集锦

1.  启动信息, 波特率设为 57600


U-Boot 1.1.3 (Mar 10 2013 - 21:51:08)
Board: Ralink APSoC DRAM:  32 MB
relocate_code Pointer at: 81fb4000
spi_wait_nsec: 42 
spi device id: c2 20 16 c2 20 (2016c220)
find flash: MX25L3205D

.*** Warning - bad CRC, using default environment
============================================ 
Ralink UBoot Version: 3.5.3.0
-------------------------------------------- 
ASIC 5350_MP (Port5<->None)
DRAM_CONF_FROM: Boot-Strapping 
DRAM_TYPE: SDRAM 
DRAM_SIZE: 256 Mbits
DRAM_WIDTH: 16 bits
DRAM_TOTAL_WIDTH: 16 bits
TOTAL_MEMORY_SIZE: 32 MBytes
Flash component: SPI Flash
Date:Mar 10 2013  Time:21:51:08
============================================ 
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:128, ways:4, linesz:32 ,total:16384 
 ##### The CPU freq = 360 MHZ #### 
 estimate memory size =32 Mbytes

Please choose the operation: 
   1: Load system code to SDRAM via TFTP. 
   2: Load system code then write to Flash via TFTP. 
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   7: Load Boot Loader code then write to Flash via Serial. 
   9: Load Boot Loader code then write to Flash via TFTP. 
 0 

3: System Boot system code via Flash.

## Booting image at bc050000 ...
.   Image Name:   Linux Kernel Image
   Created:      2013-07-24  14:41:09 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    3547254 Bytes =  3.4 MB
   Load Address: 80000000
   Entry Point:  80322000
.......................................................
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80322000) ...
## Giving linux memsize in MB, 32

Starting kernel ...
LINUX started...

 THIS IS ASIC
Linux version 2.6.21 ([e-mail]) (gcc version 3.4.2) #101 Wed Jul 24 22:17:14 CST 2013


 The CPU feqenuce set to 360 MHz
CPU revision is: 0001964c
Determined physical RAM map:
 memory: 02000000 @ 00000000 (usable)
Built 1 zonelists.  Total pages: 8128
Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock5
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 16kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
Cache parity protection disabled
cause = c0808060, status = 11000000
PID hash table entries: 128 (order: 7, 512 bytes)
calculating r4koff... 0015f900(1440000)
CPU frequency 360.00 MHz
Using 180.000 MHz high precision timer.
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 29052k/32768k available (2376k kernel code, 3716k reserved, 827k data, 112k init, 0k highmem)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
Time: MIPS clocksource has been installed.
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
deice id : c2 20 16 c2 20 (2016c220)
MX25L3205D(c2 2016c220) (4096 Kbytes)
mtd .name = raspi, .size = 0x00400000 (4M) .erasesize = 0x00010000 (64K) .numeraseregions = 0
Creating 7 MTD partitions on "raspi":
0x00000000-0x00400000 : "ALL"
0x00000000-0x00030000 : "Bootloader"
0x00030000-0x00040000 : "Config"
0x00040000-0x00050000 : "Factory"
0x00050000-0x001580b6 : "Kernel"
mtd: partition "Kernel" doesn't end on an erase block -- force read-only
0x001580b6-0x01000000 : "RootFS"
mtd: partition "RootFS" extends beyond the end of device "raspi" -- size truncated to 0x2a7f4a
mtd: partition "RootFS" doesn't start on an erase block boundary -- force read-only
0x00050000-0x01000000 : "Kernel_RootFS"
mtd: partition "Kernel_RootFS" extends beyond the end of device "raspi" -- size truncated to 0x3b0000
RT3xxx EHCI/OHCI init.
squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
squashfs: LZMA suppport for slax.org by jro
fuse init (API version 7.8)
io scheduler noop registered (default)
Ralink gpio driver initialized
Serial: 8250/16550 driver $Revision: 1.7 $ 2 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0xb0000500 (irq = 37) is a 16550A
serial8250: ttyS1 at I/O 0xb0000c00 (irq = 12) is a 16550A
rdm_major = 254
MAC_ADRH -- : 0x00000000
MAC_ADRL -- : 0x00000000
Ralink APSoC Ethernet Driver Initilization. v2.0  256 rx/tx descriptors allocated, mtu = 1500!


============== POWER ON CHECK OK(5) ==============


MAC_ADRH -- : 0x0000000c
MAC_ADRL -- : 0x433001fe
PROC INIT OK!
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
Linux video capture interface: v2.00
usbcore: registered new interface driver ov511
drivrs/media/video/ov511.c: mera Driver
drivers/media/video/se401.c: SE401 usb camera driver version 0.24 registering
usbcore: registered new interface driver se401
usbcore: registered new interface driver stv680
drivers/media/video/stv680.c: [usb_stv680_init:1543] STV(i): usb camera driver version v0.25 registering
drivers/media/video/stv680.c: STV0680 USB Camera Driver v0.25
sn9c102: V4L2 driver for SN9C1xx PC Camera Controllers v1:1.34
usbcore: registered new interface driver sn9c102
et61x251: V4L2 driver for ET61X[12]51 PC Camera Controllers v1:1.04
usbcore: registered new interface driver et61x251
pwc: Philips webcam module version 10.0.12 loaded.
pwc: Supports Philips PCA645/646, PCVC675/680/690, PCVC720[40]/730/740/750 & PCVC830/840.
pwc: Also supports the Askey VC010, various Logitech Quickcams, Samsung MPC-C10 and MPC-C30,
pwc: the Creative WebCam 5 & Pro Ex, SOTEC Afina Eye and Visionite VCS-UC300 and VCS-UM100.
usbcore: registered new interface driver Philips webcam
zc0301: V4L2 driver for ZC0301[P] Image Processor and Control Chip v1:1.07
usbcore: registered new interface driver zc0301
drivers/media/video/usbvideo/usbvideo.c: usbvideo_register: module == NULL!
usbcore: registered new interface driver ibmcam
drivers/media/video/usbvideo/usbvideo.c: usbvideo_register: module == NULL!
usbcore: registered new interface driver ultracam
drivers/media/video/usbvideo/konicawc.c: Konica Webcam driver v1.4
drivers/media/video/usbvideo/usbvideo.c: usbvideo_register: module == NULL!
usbcore: registered new interface driver konicawc
usbcore: registered new interface driver vicam
drivers/media/video/usbvideo/quickcam_messenger.c: Logitech Quickcam Messenger USB v0.01
drivers/media/video/usbvideo/usbvideo.c: usbvideo_register: module == NULL!
usbcore: registered new interface driver QCM
usbcore: registered new interface driver uvcvideo
USB Video Class driver (SVN r209)
block2mtd: version $Revision: 1.1.1.1 $
rt3xxx-ehci rt3xxx-ehci: Ralink EHCI Host Controller
rt3xxx-ehci rt3xxx-ehci: new USB bus registered, assigned bus number 1
rt3xxx-ehci rt3xxx-ehci: irq 18, io mem 0x101c0000
rt3xxx-ehci rt3xxx-ehci: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
rt3xxx-ohci rt3xxx-ohci: RT3xxx OHCI Controller
rt3xxx-ohci rt3xxx-ohci: new USB bus registered, assigned bus number 2
rt3xxx-ohci rt3xxx-ohci: irq 18, io mem 0x101c1000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial Driver core
drivers/usb/serial/usb-serial.c: USB Serial support registered for GSM modem (1-port)
usbcore: registered new interface driver option
drivers/usb/serial/option.c: USB Driver for GSM modems: v0.7.1
nf_conntrack version 0.5.0 (256 buckets, 2048 max)
ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Restricted Cone
arp_tables: (C) 2002 David S. Miller
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear
All bugs added by David S. Miller
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 112k freed


init started: BusyBox v1.12.1 (2013-07-06 22:51:37 CST)


starting pid 642, tty '': '/etc_ro/rcS'
Algorithmics/MIPS FPU Emulator v1.5
devpts: called with bogus options


Please press Enter to activate this console. internet.sh
Password for 'root' changed
phy_tx_ring = 0x01ead000, tx_ring = 0xa1ead000
phy_rx_ring0 = 0x01eae000, rx_ring0 = 0xa1eae000
RT305x_ESW: Link Status Changed


##### disable 1st wireless interface #####
rmmod: rt2860v2_ap: No such file or directory
rmmod: rt2860v2_sta: No such file or directory
Commit crc = e613d0a6
rt2860v2_ap: module license 'unspecified' taints kernel.

=== pAd = c004c000, size = 630176 ===


<-- RTMPAllocAdapterBlock, Status=0
rmmod: nf_nat_pptp: No such file or directory
rmmod: nf_conntrack_pptp: No such file or directory
rmmod: nf_nat_proto_gre: No such file or directory
rmmod: nf_conntrack_proto_gre: No such file or directory
RX DESC a1d14000  size = 2048
<-- RTMPAllocTxRxRingMemory, Status=0
Key1Str is Invalid key length(0) or Type(0)
Key2Str is Invalid key length(0) or Type(0)
Key3Str is Invalid key length(0) or Type(0)
Key4Str is Invalid key length(0) or Type(0)
1. Phy Mode = 9
2. Phy Mode = 9
3. Phy Mode = 9
RTMPSetPhyMode: channel is out of range, use first channel=0 
MCS Set = ff 00 00 00 01
SYNC - BBP R4 to 20MHz.l
Main bssid = 00:0c:43:30:01:fc
<==== rt28xx_init, Status=0
0x1300 = 00064380
vconfig: ioctl error for rem: Invalid argument
vconfig: ioctl error for rem: Invalid argument
rmmod: 8021q: No such file or directory
insmod: 8021q.ko: module not found
eth2.2: Setting MAC address to  00 0c 43 30 01 fa.
device eth2 entered promiscuous mode
VLAN (eth2.2):  Setting underlying device (eth2) to promiscious mode.
ifconfig: ioctl 0x8913 failed: No such device
brctl: bridge br0: No such device or address
iptables v1.4.0rc1: can't initialize iptables table `mangle': Table does not exist (do you need to insmod?)
Perhaps iptables or your kernel needs to be upgraded.
############ Gateway ############
##### config Ralink ESW vlan partition (LLLLW) #####
switch reg write offset=14, value=405555
switch reg write offset=50, value=2001
switch reg write offset=98, value=7f3f
switch reg write offset=e4, value=3f
switch reg write offset=40, value=1001
switch reg write offset=44, value=1001
switch reg write offset=48, value=1002
switch reg write offset=70, value=ffff506f
done.
device ra0 entered promiscuous mode
eth2.1: dev_set_promiscuity(master, 1)
device eth2.1 entered promiscuous mode
udhcpc (v1.12.1) started
br0: port 2(eth2.1) entering learning state
br0: port 1(ra0) entering learning state
ifconfig: ioctl 0x8914 failed: Cannot assign requested address
ifconfig: ioctl 0x8914 failed: Cannot assign requested address
================ CONFIG UDHCPD ================
killall: udhcpd: no process killed
Set: phy[0].reg[0] = 3900
Set: phy[1].reg[0] = 3900
Set: phy[2].reg[0] = 3900
Set: phy[3].reg[0] = 3900
Set: phy[0].reg[0] = 3100
Set: phy[1].reg[0] = 3100
Set: phy[2].reg[0] = 3100
Set: phy[3].reg[0] = 3100
killall rt2860apd 1>/dev/null 2>&1
iptables -F -t filter 1>/dev/null 2>&1
iptables -D FORWARD -j macipport_filter 1>/dev/null 2>&1
iptables -F macipport_filter 1>/dev/null 2>&1
iptables -D FORWARD -j web_filter  1>/dev/null 2>&1
iptables -F web_filter  1>/dev/null 2>&1
iptables -D FORWARD -j malicious_filter 1>/dev/null 2>&1
iptables -F malicious_filter  1>/dev/null 2>&1
iptables -D INPUT -j malicious_input_filter 1>/dev/null 2>&1
iptables -F malicious_input_filter  1>/dev/null 2>&1
iptables -P INPUT ACCEPT
iptables -P OUTPUT ACCEPT
iptables -P FORWARD ACCEPT
iptables -t filter -N web_filter 1>/dev/null 2>&1
iptables -t filter -N macipport_filter 1>/dev/null 2>&1
iptables -t filter -N malicious_filter 1>/dev/null 2>&1
iptables -t filter -N synflood_filter 1>/dev/null 2>&1
iptables -t filter -N malicious_input_filter 1>/dev/null 2>&1
iptables -t filter -N synflood_input_filter 1>/dev/null 2>&1
iptables -t filter -A FORWARD -j web_filter 1>/dev/null 2>&1
iptables -t filter -A FORWARD -j macipport_filter 1>/dev/null 2>&1
iptables -t filter -A FORWARD -j malicious_filter 1>/dev/null 2>&1
iptables -t filter -A malicious_filter -p tcp --syn -j synflood_filter 1>/dev/null 2>&1
iptables -t filter -A INPUT -j malicious_input_filter 1>/dev/null 2>&1
iptables -t filter -A malicious_input_filter -p tcp --syn -j synflood_input_filter 1>/dev/null 2>&1
iptables -A FORWARD -p tcp --tcp-flags SYN,RST SYN -j TCPMSS --clamp-mss-to-pmtu 1>/dev/null 2>&1
iptables -A malicious_input_filter -i eth2.2 -m state --state RELATED,ESTABLISHED -j ACCEPT
iptables: No chain/target/match by that name
iptables -A malicious_input_filter -i eth2.2 -m state -p tcp --dport 80 --state NEW,INVALID -j DROP
iptables: No chain/target/match by that name
/bin/super_dmz -f 1>/dev/null 2>&1
iptables -t nat -D PREROUTING -j port_forward 1>/dev/null 2>&1
iptables -t nat -F port_forward  1>/dev/null 2>&1; iptables -t nat -X port_forward  1>/dev/null 2>&1
iptables -t nat -D PREROUTING -j DMZ 1>/dev/null 2>&1
iptables -t nat -F DMZ 1>/dev/null 2>&1; iptables -t nat -X DMZ  1>/dev/null 2>&1
iptables -t nat -N port_forward 1>/dev/null 2>&1; iptables -t nat -I PREROUTING 1 -j port_forward 1>/dev/null 2>&1
iptables -t nat -N DMZ 1>/dev/null 2>&1; iptables -t nat -I PREROUTING 2 -j DMZ 1>/dev/null 2>&1
MARX_POSTROUTING_MASQUERADE matched = 0, index = 1
ntp.sh
kill -9 `cat /var/run/wscd.pid.ra0`
cat: can't open '/var/run/wscd.pid.ra0': No such file or directory
kill: you need to specify whom to kill
iwpriv ra0 set WscConfMode=0 1>/dev/null 2>&1
route delete 239.255.255.250 1>/dev/null 2>&1
killall -q klogd 1>/dev/null 2>&1
killall -q syslogd 1>/dev/null 2>&1
syslogd -C8 1>/dev/null 2>&1
klogd 1>/dev/null 2>&1
killall -q zebra 1>/dev/null 2>&1
killall -q ripd 1>/dev/null 2>&1
webs: Listening for HTTP requests at address 192.168.168.1
br0: topology change detected, propagating
br0: port 2(eth2.1) entering forwarding state
br0: topology change detected, propagating
br0: port 1(ra0) entering forwarding state