HiWiFi(极路由)集锦

1.  官方论坛 
硬件硬件方案是：
CPU：AR9331  400MHZ
内存：64M  DDR1代
FLASH：16MBwinbond25Q128BVFG
板载一个8G的缓存（其实就是一个U盘）

2. 启动信息

U-Boot 1.1.4 (Apr  8 2013 - 23:57:04)

AP121 (ar9331) U-boot

DRAM:  64 MB
Flash Manuf Id 0xef, DeviceId0 0x40, DeviceId1 0x18
flash size 16777216, sector count = 256
Flash: 16 MB
Using default environment

In:    serial
Out:   serial
Err:   serial
Net:   ag7240_enet_initialize...
No valid address in Flash. Using fixed address
No valid address in Flash. Using fixed address
ag7240 gmac: cfg1 0x5 cfg2 0x7114
eth0: 00:de:ad:be:ef:32
eth0 up
ag7240 gmac: cfg1 0xf cfg2 0x7214
eth1: 00:de:ad:be:ef:32
athrs26_reg_init_lan
ATHRS26: resetting s26
ATHRS26: s26 reset done
eth1 up
eth0, eth1
Autobooting in 2 seconds
## Booting image at 9f020000 ...
Image Name:   tw150v1-Linux-3.3.8
Created:      2013-04-09  12:23:54 UTC
Image Type:   MIPS Linux Kernel Image (lzma compressed)
Data Size:    982813 Bytes = 959.8 kB
Load Address: 80060000
Entry Point:  80060000
Verifying Checksum at 0x9f020040 ...OK
Uncompressing Kernel Image ... OK

Starting kernel ...

[    0.000000] Linux version 3.3.8 (kai.li@WEB-9-1-43) (gcc version 4.6.4 20121001 (prerelease) (Linaro GCC 4.6-2012.10) ) #1 Tue Apr 9 00:09:58 CST 2013
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[    0.000000] SoC: Atheros AR9330 rev 1
[    0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone PFN ranges:
[    0.000000]   Normal   0x00000000 -> 0x00004000
[    0.000000] Movable zone start PFN for each node
[    0.000000] Early memory PFN ranges
[    0.000000]     0: 0x00000000 -> 0x00004000
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line:  board=HC6361 console=ttyATH0,115200 mtdparts=spi0.0:64k(u-boot),64k(bdinfo)ro,1280k(kernel),14848k(rootfs),64k(nvram),64k(art)ro,16128k@0x20000(firmware) rootfstype=squashfs,jffs2 noinitrd
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 61516k/65536k available (2106k kernel code, 4020k reserved, 537k data, 176k init, 0k highmem)
[    0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:51
[    0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[    0.080000] pid_max: default: 32768 minimum: 301
[    0.080000] Mount-cache hash table entries: 512
[    0.090000] NET: Registered protocol family 16
[    0.090000] gpiochip_add: registered GPIOs 0 to 29 on device: ath79
[    0.100000] MIPS: machine is Turbo Wireless TW150V1 Board
[    0.550000] bio: create slab  at 0
[    0.560000] Switching to clocksource MIPS
[    0.560000] NET: Registered protocol family 2
[    0.570000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.570000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[    0.570000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[    0.580000] TCP: Hash tables configured (established 2048 bind 2048)
[    0.590000] TCP reno registered
[    0.590000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.600000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.600000] NET: Registered protocol family 1
[    0.630000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.630000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.640000] msgmni has been set to 120
[    0.640000] io scheduler noop registered
[    0.650000] io scheduler deadline registered (default)
[    0.650000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[    0.660000] ar933x-uart: ttyATH0 at MMIO 0x18020000 (irq = 11) is a AR933X UART
[    0.660000] console [ttyATH0] enabled, bootconsole disabled
[    0.660000] console [ttyATH0] enabled, bootconsole disabled
[    0.680000] m25p80 spi0.0: found w25q128, expected m25p80
[    0.680000] m25p80 spi0.0: w25q128 (16384 Kbytes)
[    0.690000] 7 cmdlinepart partitions found on MTD device spi0.0
[    0.690000] Creating 7 MTD partitions on "spi0.0":
[    0.700000] 0x000000000000-0x000000010000 : "u-boot"
[    0.710000] 0x000000010000-0x000000020000 : "bdinfo"
[    0.710000] 0x000000020000-0x000000160000 : "kernel"
[    0.720000] 0x000000160000-0x000000fe0000 : "rootfs"
[    0.720000] mtd: partition "rootfs" set to be root filesystem
[    0.730000] mtd: partition "rootfs_data" created automatically, ofs=6D0000, len=910000
[    0.730000] 0x0000006d0000-0x000000fe0000 : "rootfs_data"
[    0.740000] 0x000000fe0000-0x000000ff0000 : "nvram"
[    0.750000] 0x000000ff0000-0x000001000000 : "art"
[    0.750000] 0x000000020000-0x000000fe0000 : "firmware"
[    0.760000] ar933x_spiop_ioc: init
[    0.780000] ag71xx_mdio: probed
[    0.780000] eth0: Atheros AG71xx at 0xba000000, irq 5
[    1.340000] eth0: Found an AR7240/AR9330 built-in switch
[    2.370000] eth1: Atheros AG71xx at 0xb9000000, irq 4
[    2.920000] ag71xx ag71xx.0: eth1: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY]
[    2.930000] TCP cubic registered
[    2.930000] NET: Registered protocol family 17
[    2.940000] 8021q: 802.1Q VLAN Support v1.8
[    2.940000] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
[    2.950000] Freeing unused kernel memory: 176k freed
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
[   10.420000] JFFS2 notice: (422) jffs2_build_xattr_subsystem: complete building xattr subsystem, 25 of xdatum (0 unchecked, 25 orphan) and 55 of xref (0 dead, 55 orphan) found.
switching to jffs2
- init -
[   11.690000] NET: Registered protocol family 10
[   12.040000] SCSI subsystem initialized
[   12.220000] usbcore: registered new interface driver usbfs
[   12.220000] usbcore: registered new interface driver hub
[   12.230000] usbcore: registered new device driver usb
[   12.620000] ath_hal: 0.9.17.1 (AR9330)
[   12.680000] hcwifi 1.1.1.553n
[   13.110000] loop: module loaded
[   13.320000] PPP generic driver version 2.4.2
[   13.370000] IPv4 over IPv4 tunneling driver
[   13.400000] IPv6 over IPv4 tunneling driver
[   13.870000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   14.140000] NET: Registered protocol family 24
[   14.350000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   14.350000] ehci-platform ehci-platform: Generic Platform EHCI Controller
[   14.360000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[   14.400000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[   14.420000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[   14.420000] hub 1-0:1.0: USB hub found
[   14.420000] hub 1-0:1.0: 1 port detected
[   14.550000] nf_conntrack version 0.5.0 (963 buckets, 3852 max)
[   14.900000] usb 1-1: new high-speed USB device number 2 using ehci-platform
[   15.600000] xt_time: kernel timezone is -0000
[   16.240000] Initializing USB Mass Storage driver...
[   16.240000] scsi0 : usb-storage 1-1:1.0
[   16.250000] usbcore: registered new interface driver usb-storage
[   16.250000] USB Mass Storage support registered.
[   17.250000] scsi 0:0:0:0: Direct-Access     EAGET    F30              1.00 PQ: 0 ANSI: 5
[   17.260000] sd 0:0:0:0: [sda] 15155200 512-byte logical blocks: (7.75 GB/7.22 GiB)
[   17.260000] sd 0:0:0:0: [sda] Write Protect is off
[   17.270000] sd 0:0:0:0: [sda] Write cache: disabled, read cache: disabled, doesn't support DPO or FUA
[   17.570000]  sda: unknown partition table
[   17.580000] sd 0:0:0:0: [sda] Attached SCSI removable disk
[   21.490000] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   22.550000] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   22.550000] device eth0 entered promiscuous mode
[   22.570000] ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   22.600000] ADDRCONF(NETDEV_UP): eth1: link is not ready
[   26.020000] device wlan0 entered promiscuous mode
[   26.030000] br-lan: port 2(wlan0) entered forwarding state
[   26.030000] br-lan: port 2(wlan0) entered forwarding state
[   26.040000] ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   26.510000] core_vap_start: wlan0 start
[   26.540000] ath_paprd_cal: PAPRD done channel 2412
[   28.030000] br-lan: port 2(wlan0) entered forwarding state
[   43.170000] EXT4-fs (sda): mounting ext3 file system using the ext4 subsystem
[   43.190000] EXT4-fs (sda): mounted filesystem with ordered data mode. Opts: (null)
[   43.500000] Adding 65532k swap on /tmp/sda/.swap.  Priority:-1 extents:6 across:69696k
Apr 13 10:09:48 crond[1533]: crond: crond (busybox 1.19.4) started, log level 5

3. UI很新颖, 我的估计, 找个Web Server, 比如thttpd或者lightttpd, 页面实现应该没问题, 和硬件参数的交互就得靠CGI来实现了. 
之前用thttpd成功移植过一个, 用CGI实现的和底层硬件的交互, 界面大体如下

---

1. 2.