| 标题 | 阅读 | 评论 | 转发 | 发布日期 | |
|---|---|---|---|---|---|
| [Note] C6500硬件架构 | 2123 | 0 | 0 | 2009-09-17 | |
| MTU和Fragment详解 | 3794 | 0 | 0 | 2008-09-09 | |
| SSL/TLS安全会话的一个比喻 | 2571 | 0 | 0 | 2008-08-19 | |
| PIX与ASDM版本对应关系 | 2786 | 0 | 0 | 2008-07-31 | |
| [Note] 配置IOS/PIX实现SDM/ASDM管理 | 2939 | 0 | 0 | 2008-07-30 | |
| QoS操作顺序 | 1989 | 0 | 0 | 2008-06-24 | |
| secondary address详解 | 2025 | 0 | 0 | 2008-05-27 | |
| [Note] RPF Check/RPF Interface | 3091 | 0 | 0 | 2008-05-18 | |
| [Note] Quidway AR 46-20 NAT配置 | 2072 | 0 | 0 | 2008-05-08 | |
| [Note] pVLAN详解 | 3953 | 0 | 0 | 2008-04-28 | |
| 集成路由和桥接（IRB）详解 | 8313 | 0 | 0 | 2008-04-15 | |
| Voice Vlan详解 | 3295 | 0 | 0 | 2008-04-14 | |
| [Note] OSPF default-metric cost命令实现细节 | 2687 | 0 | 0 | 2008-04-11 | |
| [Note] default-information originate在OSPF中的实现详解 | 4973 | 0 | 0 | 2008-04-10 | |
| [Note] 在GNS3中使用SecureCRT方法 | 5653 | 0 | 0 | 2008-04-09 | |
| [Note] is-is SSN/SRM标志详解 | 1730 | 0 | 0 | 2008-04-08 | |
| 思科E1配置白皮书 | 3251 | 0 | 0 | 2008-04-03 | |
| 组播PIM：(*,G)和(S,G)的规则 | 2092 | 0 | 0 | 2008-04-02 | |
| 浅析网络交换机的线速WireSpeed | 1416 | 0 | 0 | 2008-03-11 | |
| 万变不离其宗 交换机典型故障归类和排除 | 1515 | 0 | 0 | 2008-03-11 |
chinaunix网友2011-01-02 23:32
你好！ 刚装的GNS 3，想配置路径配不了。在第一次运行出现的界面选择 1 结果没了反应，只看到报错 exception日志在下面。WinPcap之前没安装，所有安装默认。 Traceback (most recent call last): File "GNS3\Wizard.pyo", line 43, in slotStep1 File "GNS3\Config\Preferences.pyo", line 53, in __init__ File "GNS3\Config\Preferences.pyo", line 113, in __initDialog File "GNS3\Ui\ConfigurationPages\Page_PreferencesCapture.pyo", line 37, in __init__ File "GNS3\Ui\ConfigurationPages\Page_PreferencesCapture.pyo", line 59, in loadConf UnicodeDecodeError: 'ascii' codec can't decode byte 0xcd in position 12: ordinal not in range(128) 这个是什么问题啊？谢谢！
chinaunix网友2008-11-07 08:34
那个203-bad munber of parmeters (4 with min/max=2/2),是在拖路由器图标到工作区域时出，急求解决，谢谢！
chinaunix网友2008-09-18 10:25
小何，无意中再次光临你的博客，感觉你这里顿时蓬荜生辉。呵呵，开个玩笑。看到你还是在一如既往，感觉很欣慰。对比我真成了三无人员：无工作无男友无目标。堕落啊。
