NAND U-Boot 2010.03.OpenWrt ( 9鏈07 2011 - 20:24:38)
by Lintel(Lintel.huang@gmail.com)
I2C: ready
DRAM: 64 MB
Flash: 2 MB
NAND: 256 MiB
Video: 800x480x16 26kHz 52Hz
In: serial
Out: serial
Err: serial
Use GPC5 to enable USB slave!
USB slave is enable!
Net: dm9000
Hit any key to stop autoboot: 0
Loading from nand0, offset 0x80000
Image Name: DreamBox S3C24xx Linux-3.10.54
Created: 2014-09-19 10:51:36 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1486320 Bytes = 1.4 MB
Load Address: 30008000
Entry Point: 30008040
## Booting kernel from Legacy Image at 30008000 ...
Image Name: DreamBox S3C24xx Linux-3.10.54
Created: 2014-09-19 10:51:36 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1486320 Bytes = 1.4 MB
Load Address: 30008000
Entry Point: 30008040
Verifying Checksum ... OK
XIP Kernel Image ... OK
OK
Using machid 0x7cf from environment
MACH_TYPE_ID_HEX=0x7cf MACH_TYPE_ID_DEC=1999
LINUX_BOOT_CMD=root=/dev/mtdblock3 console=ttySAC0,115200 rootfstype=squashfs,ext2
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 3.10.54 (hades@PandoraBox-Server) (gcc version 4.8.3 (PandoraBox/Linaro GCC 4.8-2014.04 svn-r127) ) #1 Fri Sep 19 18:51:23 CST 2014
[ 0.000000] CPU: ARM920T [41129200] revision 0 (ARMv4T), cr=c0007177
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] Machine: MINI2440
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] CPU S3C2440A (id 0x32440001)
[ 0.000000] S3C24XX Clocks, Copyright 2004 Simtec Electronics
[ 0.000000] S3C244X: core 405.000 MHz, memory 101.250 MHz, peripheral 50.625 MHz
[ 0.000000] CLOCK: Slow mode (1.500 MHz), fast, MPLL on, UPLL on
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: root=/dev/mtdblock3 console=ttySAC0,115200 rootfstype=squashfs,ext2
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Memory: 64MB = 64MB total
[ 0.000000] Memory: 60492k/60492k available, 5044k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0x84800000 - 0xff000000 (1960 MB)
[ 0.000000] lowmem : 0x80000000 - 0x84000000 ( 64 MB)
[ 0.000000] modules : 0x7f000000 - 0x80000000 ( 16 MB)
[ 0.000000] .text : 0x80008000 - 0x803dad5c (3916 kB)
[ 0.000000] .init : 0x803db000 - 0x803fea58 ( 143 kB)
[ 0.000000] .data : 0x80400000 - 0x80427f64 ( 160 kB)
[ 0.000000] .bss : 0x80427f64 - 0x80454620 ( 178 kB)
[ 0.000000] NR_IRQS:111
[ 0.000000] S3C2440: IRQ Support
[ 0.000000] irq: clearing pending status 02000000
[ 0.000000] irq: clearing pending status 00000002
[ 0.000000] sched_clock: 16 bits at 1012kHz, resolution 987ns, wraps every 64ms
[ 0.000398] Calibrating delay loop... 201.52 BogoMIPS (lpj=503808)
[ 0.044936] pid_max: default: 32768 minimum: 301
[ 0.045347] Mount-cache hash table entries: 512
[ 0.047543] CPU: Testing write buffer coherency: ok
[ 0.049126] Setting up static identity map for 0x800101e0 - 0x80010240
[ 0.004802] regulator-dummy: no parameters
[ 0.007242] NET: Registered protocol family 16
[ 0.010028] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.034134] MINI2440: Option string mini2440=0tb
[ 0.034207] MINI2440: 't' ignored, touchscreen not compiled in
[ 0.034273] MINI2440: LCD [0:240x320] 1:800x480 2:1024x768 3:320x240
[ 0.057972] S3C2440: Initialising architecture
[ 0.059272] S3C244X: Clock Support, DVS off
[ 0.001705] S3C24XX CPU Frequency driver, s3c244x cpu support
[ 0.011873] bio: create slab at 0
[ 0.024940] SCSI subsystem initialized
[ 0.035050] pps_core: LinuxPPS API ver. 1 registered
[ 0.035118] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti
[ 0.036512] PTP clock support registered
[ 0.045538] Switching to clocksource samsung_clocksource_timer
[ 0.061587] NET: Registered protocol family 2
[ 0.064547] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[ 0.064653] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[ 0.064698] TCP: Hash tables configured (established 512 bind 512)
[ 0.000411] TCP: reno registered
[ 0.000506] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.000573] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.001787] NET: Registered protocol family 1
[ 0.012086] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.012174] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.013141] msgmni has been set to 118
[ 0.020877] io scheduler noop registered
[ 0.021272] io scheduler deadline registered (default)
[ 0.021399] io scheduler cfq registered
[ 0.028082] s3c2410-lcd s3c2410-lcd: fb0: s3c2410fb frame buffer device
[ 0.031574] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.036910] s3c2440-uart.0: ttySAC0 at MMIO 0x50000000 (irq = 74) is a S3C2440
[ 0.152571] console [ttySAC0] enabled
[ 0.157665] s3c2440-uart.1: ttySAC1 at MMIO 0x50004000 (irq = 77) is a S3C2440
[ 0.164722] s3c2440-uart.2: ttySAC2 at MMIO 0x50008000 (irq = 80) is a S3C2440
[ 0.181155] s3c24xx-nand s3c2440-nand: Tacls=3, 29ns Twrph0=7 69ns, Twrph1=4 39ns
[ 0.183315] s3c24xx-nand s3c2440-nand: NAND soft ECC
[ 0.188112] NAND device: Manufacturer ID: 0xec, Chip ID: 0xda (Samsung NAND 256MiB 3,3V 8-bit), 256MiB, page size: 2048, OOB size: 64
[ 0.200871] Creating 4 MTD partitions on "nand":
[ 0.204479] 0x000000000000-0x000000060000 : "u-boot"
[ 0.214806] 0x000000060000-0x000000080000 : "u-boot-env"
[ 0.220496] 0x000000080000-0x000000580000 : "kernel"
[ 0.227934] 0x000000580000-0x000010000000 : "rootfs"
[ 0.250154] mtd: device 3 (rootfs) set to be root filesystem
[ 0.250388] mtd: partition "rootfs_data" created automatically, ofs=0x7a0000, len=0xf860000
[ 0.258673] 0x0000007a0000-0x000010000000 : "rootfs_data"
[ 0.288690] dm9000 dm9000: read wrong id 0x01010101
[ 0.288803] dm9000 dm9000: eth%d: Invalid ethernet MAC address. Please set using ifconfig
[ 0.299609] eth0: dm9000e at 848b4300,848b6304 IRQ 55 MAC: ea:d7:1f:6c:09:bf (random)
[ 0.305282] s3c-rtc s3c2410-rtc: rtc disabled, re-enabling
[ 0.310731] s3c-rtc s3c2410-rtc: rtc core: registered s3c as rtc0
[ 0.251572] i2c /dev entries driver
[ 0.255225] s3c2410-wdt s3c2410-wdt: tmr_margin value out of range, default 15 used
[ 0.263995] s3c2410-wdt s3c2410-wdt: watchdog inactive, reset disabled, irq disabled
[ 0.270134] cpufreq: Unable to obtain msysclk: -2
[ 0.273634] cpuidle: using governor ladder
[ 0.278396] TCP: cubic registered
[ 0.280689] NET: Registered protocol family 17
[ 0.285480] 8021q: 802.1Q VLAN Support v1.8
[ 0.289520] VFP support v0.3: not present
[ 0.299170] regulator-dummy: incomplete constraints, leaving on
[ 0.302562] s3c-rtc s3c2410-rtc: setting system clock to 2000-01-02 01:26:15 UTC (946776375)
[ 0.309133] UBIFS error (pid 1): ubifs_mount: cannot open "ubi0:rootfs", error -19
[ 0.258867] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
[ 0.261258] Freeing unused kernel memory: 140K (803db000 - 803fe000)
procd: Console is alive
procd: - watchdog -
[ 1.133109] usbcore: registered new interface driver usbfs
[ 1.134369] usbcore: registered new interface driver hub
[ 1.139737] usbcore: registered new device driver usb
[ 1.153768] Button Hotplug driver version 0.4.1
[ 1.167079] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.171324] s3c2410-ohci s3c2410-ohci: S3C24XX OHCI
[ 1.172530] s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1
[ 1.115558] s3c2410-ohci s3c2410-ohci: irq 42, io mem 0x49000000
[ 1.118978] hub 1-0:1.0: USB hub found
[ 1.119144] hub 1-0:1.0: 2 ports detected
[ 1.137486] usbcore: registered new interface driver usb-storage
procd: - preinit -
kmod: module is already loaded - input-core
Failed to find input-polldev. Maybe it is a built in module ?
Failed to find gpio_buttons. Maybe it is a built in module ?
Failed to find gpio_keys. Maybe it is a built in module ?
kmod: module is already loaded - button-hotplug
kmod: module is already loaded - leds-gpio
[ 1.119052] usb 1-1: new full-speed USB device number 2 using s3c2410-ohci
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 1.201466] usb-storage 1-1:1.0: USB Mass Storage device detected
[ 1.202956] scsi0 : usb-storage 1-1:1.0
[ 1.504715] scsi 0:0:0:0: Direct-Access iT1167B USB Flash Disk 0.00 PQ: 0 ANSI: 2
[ 1.522654] sd 0:0:0:0: [sda] 7892992 512-byte logical blocks: (4.04 GB/3.76 GiB)
[ 1.529581] sd 0:0:0:0: [sda] Write Protect is off
[ 1.535595] sd 0:0:0:0: [sda] Asking for cache data failed
[ 1.535707] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 1.578585] sd 0:0:0:0: [sda] Asking for cache data failed
[ 1.578699] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 1.593984] sda: sda4
[ 1.623591] sd 0:0:0:0: [sda] Asking for cache data failed
[ 1.623703] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 1.629684] sd 0:0:0:0: [sda] Attached SCSI removable disk
kmod: module is already loaded - leds-gpio
kmod: ran 1 iterations
block: extroot: no root or overlay mount defined
jffs2 is not ready - marker found
procd: - early -
procd: - watchdog -
procd: - ubus -
procd: - init -
Please press Enter to activate this console.
[ 3.472153] NET: Registered protocol family 10
[ 3.529370] nf_conntrack version 0.5.0 (947 buckets, 3788 max)
[ 3.546083] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 3.619020] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 3.744098] xt_time: kernel timezone is -0000
[ 3.765845] PPP generic driver version 2.4.2
[ 3.708064] NET: Registered protocol family 24
[ 6.826492] dm9000 dm9000 eth0: link down
[ 6.827455] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 6.866420] device eth0 entered promiscuous mode
[ 6.868712] br-lan: port 1(eth0) entered forwarding state
[ 6.870843] br-lan: port 1(eth0) entered forwarding state
[ 7.004936] br-lan: port 1(eth0) entered disabled state
[ 7.382725] dm9000 dm9000 eth0: link up, 100Mbps, full-duplex, lpa 0xCDE1
[ 7.412680] br-lan: port 1(eth0) entered forwarding state
[ 7.412952] br-lan: port 1(eth0) entered forwarding state
[ 7.418293] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 7.445238] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[ 7.466333] jffs2_build_filesystem(): unlocking the mtd device... done.
[ 7.467327] jffs2_build_filesystem(): erasing all blocks after the end marker...
BusyBox v1.22.1 (2014-09-19 17:37:09 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.
_______________________________________________________________
| ____ _ ____ |
| | _ \ __ _ _ __ __| | ___ _ __ __ _| __ ) _____ __ |
| | |_) / _` | '_ \ / _` |/ _ \| '__/ _` | _ \ / _ \ \/ / |
| | __/ (_| | | | | (_| | (_) | | | (_| | |_) | (_) > < |
| |_| \__,_|_| |_|\__,_|\___/|_| \__,_|____/ \___/_/\_\ |
| |
| PabdoraBox SDK Plantform |
| Copyright 2013-2014 |
| D-Team Technology Co.,Ltd. ShenZhen |
|______________________________________________________________|
Base on OpenWrt BARRIER BREAKER (14.09, r130)
[root@PandoraBox:/]#[ 7.993596] br-lan: port 1(eth0) entered forwarding state
done.
[ 31.042358] jffs2: notice: (826) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
procd: - init complete -
阅读(8510) | 评论(1) | 转发(0) |
