//---- 8M Flash, 64M RAM, U-boot中有4M和8M的区别, 但Openwrt中都识别为8M
以我的理解，如果不通过TTL在uboot下操作flash，不需要修改uboot，因为openwrt可以正确识别flash大小，但是一旦固件出问题，需要在TTL访问整个flash空间的时候，uboot中的flash大小定义不正确就有问题了。
//---- 刷8M U-boot后的启动信息
U-Boot 1.1.4 (May 3 2012 - 22:04:42)
AP121 (ar9330) U-boot
DRAM: 64 MB
led turning on for 1s...
id read 0x100000ff
flash size 8388608, sector count = 128
Flash: 8 MB
Using default environment
In: serial
Out: serial
Err: serial
Net: ag7240_enet_initialize...
No valid address in Flash. Using fixed address
No valid address in Flash. Using fixed address
: cfg1 0x5 cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
ag7240_phy_setup
eth0 up
: cfg1 0xf cfg2 0x7214
eth1: 00:03:7f:09:0b:ad
athrs26_reg_init_lan
ATHRS26: resetting s26
ATHRS26: s26 reset done
ag7240_phy_setup
eth1 up
eth0, eth1
Autobooting in 3 seconds
## Booting image at 9f020000 ...
Uncompressing Kernel Image ... OK
Starting kernel ...
Linux version 2.6.39.4 (palmerxiaobiao@palmerxiaobiao-desktop) (gcc version 4.5.4 20110808 (prerelease) (Linaro GCC 4.5-2011.08) ) #1 Sat Nov 26 12:12:30 CST 2011
bootconsole [early0] enabled
CPU revision is: 00019374 (MIPS 24Kc)
SoC: Atheros AR9330 rev 1
Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
Determined physical RAM map:
memory: 04000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
Normal 0x00000000 -> 0x00004000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00004000
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
Kernel command line: board=TL-WR703N console=ttyATH0,115200 rootfstype=squashfs,jffs2 noinitrd
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Writing ErrCtl register=00000000
Readback ErrCtl register=00000000
Memory: 61828k/65536k available (2027k kernel code, 3708k reserved, 396k data, 184k init, 0k highmem)
SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
NR_IRQS:80
Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
NET: Registered protocol family 16
MIPS: machine is TP-LINK TL-WR703N v1
bio: create slab at 0
Switching to clocksource MIPS
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
msgmni has been set to 120
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
ar933x-uart: ttyATH0 at MMIO 0x18020000 (irq = 11) is a AR933X UART
console [ttyATH0] enabled, bootconsole disabled
console [ttyATH0] enabled, bootconsole disabled
Atheros AR71xx SPI Controller driver version 0.2.4
m25p80 spi0.0: found mx25l6405d, expected m25p80
m25p80 spi0.0: mx25l6405d (8192 Kbytes)
Searching for RedBoot partition table in spi0.0 at offset 0x7e0000
Searching for RedBoot partition table in spi0.0 at offset 0x7f0000
No RedBoot partition table detected in spi0.0
spi0.0: no WRT160NL signature found
Creating 5 MTD partitions on "spi0.0":
0x000000000000-0x000000020000 : "u-boot"
0x000000020000-0x000000120000 : "kernel"
0x000000120000-0x0000007f0000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=5A0000, len=250000
0x0000005a0000-0x0000007f0000 : "rootfs_data"
0x0000007f0000-0x000000800000 : "art"
0x000000020000-0x0000007f0000 : "firmware"
ag71xx_mdio: probed
eth0: Atheros AG71xx at 0xb9000000, irq 4
Atheros AR71xx hardware watchdog driver version 0.1.0
TCP westwood registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear
All bugs added by David S. Miller
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 184k freed
input: gpio-keys-polled as /devices/platform/gpio-keys-polled/input/input0
Button Hotplug driver version 0.4.1
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
JFFS2 notice: (404) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 15 of xref (0 dead, 0 orphan) found.
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ar71xx-ehci ar71xx-ehci: Atheros AR91xx built-in EHCI controller
ar71xx-ehci ar71xx-ehci: new USB bus registered, assigned bus number 1
ar71xx-ehci ar71xx-ehci: irq 3, io mem 0x1b000000
ar71xx-ehci ar71xx-ehci: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
switching to jffs2
- init -
Please press Enter to activate this console. Compat-wireless backport release: compat-wireless-2011-11-08-1-g4ab9b62
Backport based on wireless-testing.git master-2011-11-15
cfg80211: Calling CRDA to update world regulatory domain
cfg80211: World regulatory domain updated:
cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
ieee80211 phy0: Atheros AR9330 Rev:1 mem=0xb8100000, irq=2
cfg80211: Calling CRDA for country: US
cfg80211: Regulatory domain changed to country: US
cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
PPP generic driver version 2.4.2
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky
ip_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 24
nf_conntrack version 0.5.0 (968 buckets, 3872 max)
xt_time: kernel timezone is -0000
usbcore: registered new interface driver cdc_acm
cdc_acm: v0.26:USB Abstract Control Model driver for USB modems and ISDN adapters
usbcore: registered new interface driver usblp
usbcore: registered new interface driver usbserial
USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
usbserial: USB Serial Driver core
usbcore: registered new interface driver ums-alauda
usbcore: registered new interface driver ums-cypress
usbcore: registered new interface driver ums-datafab
usbcore: registered new interface driver ums-freecom
usbcore: registered new interface driver ums-isd200
usbcore: registered new interface driver ums-jumpshot
usbcore: registered new interface driver ums-karma
usbcore: registered new interface driver ums-sddr09
usbcore: registered new interface driver ums-sddr55
usbcore: registered new interface driver ums-usbat
USB Serial support registered for GSM modem (1-port)
usbcore: registered new interface driver option
option: v0.7.2:USB Driver for GSM modems
device wlan0 entered promiscuous mode
br-lan: port 1(wlan0) entering forwarding state
br-lan: port 1(wlan0) entering forwarding state
device wlan0 left promiscuous mode
br-lan: port 1(wlan0) entering forwarding state
device wlan0 entered promiscuous mode
br-lan: port 1(wlan0) entering forwarding state
br-lan: port 1(wlan0) entering forwarding state
ar71xx-wdt: enabling watchdog timer
ar71xx-wdt: timeout=60 secs
br-lan: port 1(wlan0) entering forwarding state
u32 classifier
Performance counters on
input device check on
Actions configured
Mirror/redirect action on
HTB: quantum of class 10040 is small. Consider r2q change.
HTB: quantum of class 10050 is small. Consider r2q change.
//-----刷4M U-boot的启动信息, 应用正常.
U-Boot 1.1.4 (Sep 26 2011 - 11:13:45)
AP121-2MB (ar9330) U-boot
DRAM: 64 MB
led turning on for 1s...
id read 0x100000ff
flash size 4194304, sector count = 64
Flash: 4 MB //U-boot的识别
Using default environment
In: serial
Out: serial
Err: serial
Net: ag7240_enet_initialize...
No valid address in Flash. Using fixed address
No valid address in Flash. Using fixed address
: cfg1 0x5 cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
ag7240_phy_setup
eth0 up
: cfg1 0xf cfg2 0x7214
eth1: 00:03:7f:09:0b:ad
athrs26_reg_init_lan
ATHRS26: resetting s26
ATHRS26: s26 reset done
ag7240_phy_setup
eth1 up
eth0, eth1
Autobooting in 1 seconds
## Booting image at 9f020000 ...
Uncompressing Kernel Image ... OK
Starting kernel ...
Linux version 2.6.39.4 (palmerxiaobiao@palmerxiaobiao-desktop) (gcc version 4.5.4 20110808 (prerelease) (Linaro GCC 4.5-2011.08) ) #1 Sat Nov 26 12:12:30 CST 2011
bootconsole [early0] enabled
CPU revision is: 00019374 (MIPS 24Kc)
SoC: Atheros AR9330 rev 1
Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
Determined physical RAM map:
memory: 04000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
Normal 0x00000000 -> 0x00004000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00004000
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
Kernel command line: board=TL-WR703N console=ttyATH0,115200 rootfstype=squashfs,jffs2 noinitrd
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Writing ErrCtl register=00000000
Readback ErrCtl register=00000000
Memory: 61828k/65536k available (2027k kernel code, 3708k reserved, 396k data, 184k init, 0k highmem)
SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
NR_IRQS:80
Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
NET: Registered protocol family 16
MIPS: machine is TP-LINK TL-WR703N v1
bio: create slab at 0
Switching to clocksource MIPS
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
msgmni has been set to 120
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
ar933x-uart: ttyATH0 at MMIO 0x18020000 (irq = 11) is a AR933X UART
console [ttyATH0] enabled, bootconsole disabled
console [ttyATH0] enabled, bootconsole disabled
Atheros AR71xx SPI Controller driver version 0.2.4
m25p80 spi0.0: found mx25l6405d, expected m25p80
m25p80 spi0.0: mx25l6405d (8192 Kbytes)
Searching for RedBoot partition table in spi0.0 at offset 0x7e0000
Searching for RedBoot partition table in spi0.0 at offset 0x7f0000
No RedBoot partition table detected in spi0.0
spi0.0: no WRT160NL signature found
Creating 5 MTD partitions on "spi0.0":
0x000000000000-0x000000020000 : "u-boot"
0x000000020000-0x000000120000 : "kernel"
0x000000120000-0x0000007f0000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=5A0000, len=250000
0x0000005a0000-0x0000007f0000 : "rootfs_data"
0x0000007f0000-0x000000800000 : "art"
0x000000020000-0x0000007f0000 : "firmware" //Openwrt中的识别
ag71xx_mdio: probed
eth0: Atheros AG71xx at 0xb9000000, irq 4
Atheros AR71xx hardware watchdog driver version 0.1.0
TCP westwood registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear
All bugs added by David S. Miller
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 184k freed
input: gpio-keys-polled as /devices/platform/gpio-keys-polled/input/input0
Button Hotplug driver version 0.4.1
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
JFFS2 notice: (403) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 58 of xref (0 dead, 0 orphan) found.
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ar71xx-ehci ar71xx-ehci: Atheros AR91xx built-in EHCI controller
ar71xx-ehci ar71xx-ehci: new USB bus registered, assigned bus number 1
ar71xx-ehci ar71xx-ehci: irq 3, io mem 0x1b000000
ar71xx-ehci ar71xx-ehci: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
//------------------------------------------------------------------------------
原厂的启动信息
U-Boot 1.1.4 (Aug 17 2011 - 15:38:49)
AP121-2MB (ar9330) U-boot
DRAM: 32 MB
led turning on for 1s...
id read 0x100000ff
flash size 4194304, sector count = 64
Flash: 4 MB
Using default environment
In: serial
Out: serial
Err: serial
Net: ag7240_enet_initialize...
No valid address in Flash. Using fixed address
No valid address in Flash. Using fixed address
: cfg1 0x5 cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
ag7240_phy_setup
eth0 up
: cfg1 0xf cfg2 0x7214
eth1: 00:03:7f:09:0b:ad
athrs26_reg_init_lan
ATHRS26: resetting s26
ATHRS26: s26 reset done
ag7240_phy_setup
eth1 up
eth0, eth1
Autobooting in 1 seconds
## Booting image at 9f020000 ...
Uncompressing Kernel Image ... OK
Starting kernel ...
Booting AR9330(Hornet)...
Linux version 2.6.31--LSDK-9.2.0.312 (root@bogon) (gcc version 4.3.3 (GCC) ) #13
...
Searching for RedBoot partition table
5 RedBoot partitions found on MTD device ar7240-nor0
Creating 5 MTD partitions on "ar7240-nor0":
0x000000000000-0x000000020000 : "boot"
0x000000020000-0x000000120000 : "kernel"
0x000000120000-0x0000003e0000 : "rootfs"
0x0000003e0000-0x0000003f0000 : "config"
0x0000003f0000-0x000000400000 : "art"
--------------------------------------------------------------------------------------
|
