Juniper
1）show chassis alarms / show system alarms
该是用来查看硬件存在的告警和软件告警，如果没有异常状态,那么操作结果应该显示No alarms currently active。例如:
No alarms currently active
2）show interfaces terse
该命令是用来查看端口的状态的，正常情况下,已经配置了的端口admin和link状态应该为up。例如:
Interface Admin Link Proto Local Remote
ce1-0/0/0 up up
e1-0/0/0 up up
e1-0/0/0.0 up up mlppp ls-0/2/0.0
ce1-0/0/1 up up
e1-0/0/1 up up
e1-0/0/1.0 up up mlppp ls-0/2/0.0
…………………………………………………………………….
…………………………………………………………………..
3）show chassis hardware
该命令用来查看硬件版本信息、编号、串口号及描述，正常情况下,所有已经安装的硬件模块都会被检测到。例如:
Hardware inventory:
Item Version Part number Serial number Description
Chassis A3951 M7i
Midplane REV 04 710-008761 CV8447 M7i Midplane
Power Supply 0 Rev 02 740-008985 6297095 DC Power Supply
Power Supply 1 Rev 02 740-008985 6297079 DC Power Supply
Routing Engine REV 12 740-009459 1000649031 RE-5.0
CFEB REV 07 750-010463 CT8481 Internet Processor II
FPC 0 E-FPC
PIC 0 REV 15 750-007626 CS6602 10x CHE1 IQ
PIC 1 REV 15 750-007626 CS6581 10x CHE1 IQ
PIC 2 REV 06 750-007927 CW3453 1x Link Service(4)
PIC 3 REV 12 750-012838 DB1228 4x 1GE(LAN), IQ2
SFP 2 REV 01 740-011782 PB81N3B SFP-SX
SFP 3 REV 01 740-011783 PB30PQX SFP-LX
FPC 1 E-FPC
PIC 2 BUILTIN BUILTIN 1x Tunnel
PIC 3 REV 10 750-009098 CV7985 2x F/E, 100 BASE-TX
show chassis enviroment
该命令用来查看设备的运行环境,例如硬件的温度,风扇的运转是否正常，看到OK即表示正常。例如:
> show chassis environment
Class Item Status
Measurement
Power Power Supply 0
OK
Power Supply 1
OK
Temp Intake OK 23 degrees C / 73 degrees
F
FPC 0 OK 28 degrees C / 82 degrees
F
Power Supplies OK 30 degrees C / 86 degrees
F
CFEB Intake OK 23 degrees C / 73 degrees
F
CFEB Exhaust OK 29 degrees C / 84 degrees
F
Routing Engine OK 30 degrees C / 86 degrees
F
Fans Fan 1 OK Spinning at normal
speed
Fan 2 OK Spinning at normal
speed
Fan 3 OK Spinning at normal
speed
Fan 4 OK Spinning at normal speed
5）show chassis fpc
该命令用来查看FPC板卡的运行情况，fpc板卡都是online状态及cpu利用率cpu utillzation(正常10%)。例如:
Temp CPU Utilization (%) Memory Utilization (%)
Slot State (C) Total Interrupt DRAM (MB) Heap
Buffer
0 Online 4 0 128 12 26
1 Online 4 0 128 12 26
show ospf neigbhor
该命令用来查看OSPF邻居建立状态。现在的爱立信的juniper设备已经准备退网了，很多网元已经割接到华为的设备去了，配置的数据也少了很多，所以看到的配置信息也基本没什么了。例如:
OSPF instance is not running
7) show log
该命令用来查看日志信息。其实跟华为的设备基本一样显示的是日志的记录信息。
8)show system processes extensive
该命令用来查看路由进程引擎的各进程状态，确认无无异常进程,确认单个CPU的占用率低于5%。例如：
last pid: 63370; load averages: 0.00, 0.00, 0.00 up 559+08:17:48 09:11:28
64 processes: 1 running, 63
sleeping
Mem: 126M Active, 54M Inact, 47M Wired, 9724K Cache, 35M Buf, 8416K
Free
Swap: 512M Total, 512M
Free
PID USERNAME PRI NICE SIZE RES STATE TIME WCPU CPU COMMAND
63370 root 29 0 21760K 1024K RUN 0:01 55.00% 2.69%
top
2970 root 10 0 71512K 56324K nanslp 339.1H 1.71% 1.71% chassisd
63289 root 2 0 14460K 8348K select 0:00 0.10% 0.10% mgd
2988 root 2 0 1948K 1400K select 25.3H 0.00% 0.00% ppmd
2977 root 2 0 12228K 8632K kqread 559:15 0.00% 0.00% rpd
3005 root 2 0 5060K 4200K select 187:03 0.00% 0.00% dcd
2971 root 2 0 1872K 1088K select 122:04 0.00% 0.00% alarmd
2992 root 2 0 1444K 888K select 115:00 0.00% 0.00% irsd
………………………………………………………………………………………
………………………………………………………………………………………
9）show route summary
该命令查看路由的配置总数，可以对比与策划的是否一样。
Autonomous system number:
65001
Router ID:
192.168.220.1
inet.0: 206 destinations, 206 routes (206 active, 0 holddown, 0
hidden)
Direct: 11 routes, 11
active
Local: 8 routes, 8
active
Static: 3 routes, 3
active
IS-IS: 184 routes, 184 active
…………………………………………………………………………..
…………………………………………………………………………..
阅读(2506) | 评论(0) | 转发(0) |
