1、复制usb slave驱动源代码
创建drivers/usb/slave 目录,复制usb slave驱动源代码到此目录(详见附件)
2、修改uboot根目录下的Makefeils,添加红色部分代码
LIBS += drivers/usb/musb/libusb_musb.a
# Apollo +
LIBS += drivers/usb/slave/libusb_slave.a
# Apollo -
LIBS += drivers/video/libvideo.a |
3、修改lib_arm/board.c文件,添加红色部分代码
//Apollo +
Port_Init(); /* enable exceptions */ enable_interrupts (); usb_init();
//Apollo -
|
4、修改平台头文件,include/configs/utu2440.h,添加红色部分
#define CONFIG_USB_DEVICE 1
#ifdef CONFIG_USB_DEVICE
#define CONFIG_USE_IRQ 1
#endif
//#undef CONFIG_USE_IRQ /* we don't need IRQ/FIQ stuff */ |
5、修改cpu/arm920t/s3c24x0/interrupts.c 文件,添加arch_interrupt_init函数定义
//Apollo +
int arch_interrupt_init (void) { return 0; } //Apollo -
|
6、修改cpu/arm920t/start.S,文件
#ifdef CONFIG_USE_IRQ .align 5 irq: //Apollo +,此处开始修改 /* get_irq_stack irq_save_user_regs bl do_irq irq_restore_user_regs */
/* use IRQ for USB and DMA */ sub lr, lr, #4 @ the return address ldr sp, IRQ_STACK_START @ the stack for irq stmdb sp!, { r0-r12,lr } @ save registers ldr lr, =int_return @ set the return addr ldr pc, =IRQ_Handle @ call the isr int_return: ldmia sp!, { r0-r12,pc }^ @ return from interrupt //Apollo -,修改结束
|
7、修改include/s3c24x0.h,文件
//Apollo +
S3C24X0_REG8 MAXP_REG; // S3C24X0_REG8 res10[7]; S3C24X0_REG8 res10[3]; S3C24X0_REG8 EP0_CSR_IN_CSR1_REG; S3C24X0_REG8 res11[3]; S3C24X0_REG8 IN_CSR2_REG; // S3C24X0_REG8 res12[3]; S3C24X0_REG8 res12[7]; S3C24X0_REG8 OUT_CSR1_REG; // S3C24X0_REG8 res13[7]; S3C24X0_REG8 res13[3];
//Apollo -
|
8、添加usbslave命令
在common目录下创建cmd_usbslave.c
#include <common.h> #include <command.h> #include <asm/byteorder.h>
#ifdef CONFIG_USB_DEVICE
#ifdef CONFIG_USE_IRQ #define IRQ_STACK_START (_armboot_start - CONFIG_SYS_MALLOC_LEN - CONFIG_SYS_GBL_DATA_SIZE - 4) #define FIQ_STACK_START (IRQ_STACK_START - CONFIG_STACKSIZE_IRQ) #define FREE_RAM_END (FIQ_STACK_START - CONFIG_STACKSIZE_FIQ - CONFIG_STACKSIZE) #define FREE_RAM_SIZE (FREE_RAM_END - PHYS_SDRAM_1) #else #define FREE_RAM_END (_armboot_start - CONFIG_SYS_MALLOC_LEN - CONFIG_SYS_GBL_DATA_SIZE - 4 - CONFIG_STACKSIZE) #define FREE_RAM_SIZE (FREE_RAM_END - PHYS_SDRAM_1) #endif
int g_bUSBWait = 1; u32 g_dwDownloadLen = 0;
extern int download_run; extern volatile unsigned int dwUSBBufBase; extern volatile unsigned int dwUSBBufSize;
extern __u32 usb_receive(char *buf, size_t len, unsigned int wait);
int do_usbslave (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) { int i; size_t len = ~0UL; char buf[32];
/* download_run为1时表示将文件保存在USB Host发送工具dnw指定的位置 * download_run为0时表示将文件保存在参数argv[2]指定的位置 * 要下载程序到内存,然后直接运行时,要设置download_run=1,这也是这个参数名字的来由 */ download_run = 1; switch (argc) { case 1: { break; } case 2: { g_bUSBWait = (int)simple_strtoul(argv[1], NULL, 16); break; }
case 3: { g_bUSBWait = (int)simple_strtoul(argv[1], NULL, 16); load_addr = simple_strtoul(argv[2], NULL, 16); download_run = 0; break; } default: { printf ("Usage:\n%s\n", cmdtp->usage); return 1; } }
dwUSBBufBase = load_addr; dwUSBBufSize = (FREE_RAM_SIZE&(~(0x80000-1))); if (g_bUSBWait) len = FREE_RAM_SIZE;
g_dwDownloadLen = usb_receive(dwUSBBufBase, len, g_bUSBWait); sprintf(buf, "%X", g_dwDownloadLen); setenv("filesize", buf); return 0; }
U_BOOT_CMD( usbslave, 3, 0, do_usbslave, "usbslave - get file from host(PC)\n", "[wait] [loadAddress]\n" "\"wait\" is 0 or 1, 0 means for return immediately, not waits for the finish of transferring\n" );
#endif
|
修改common/Makefile
COBJS-$(CONFIG_USB_KEYBOARD) += usb_kbd.o
# Apollo +
COBJS-$(CONFIG_USB_DEVICE) += cmd_usbslave.o
# Apollo - |
|
文件: |
uboot-usb_slave.tar.bz2 |
大小: |
17KB |
下载: |
下载 | |
阅读(3560) | 评论(0) | 转发(0) |