分类： 嵌入式
2011-07-15 11:05:44
//======================================================================
// 工程名称： IIC.mcp
// 功能描述： 通过超级终端可以看到IIC传输状态及其结果
//
// IDE环境： TX2440A ADS v1.2
// 组成文件： main.c, IIC.c IIC.h
// 硬件连接： 使用AT24C04
// 维护记录： 2009-8-26 V1.0
//======================================================================
#include "2440lib.h"
#include "2440addr.h"
#include "def.h"
#include "uart.h"
#include
#define WRDATA (1)
#define POLLACK (2)
#define RDDATA (3)
#define SETRDADDR (4)
#define IICBUFSIZE 0x20
static U8 _iicData[IICBUFSIZE];
static volatile int _iicDataCount;
static volatile int _iicStatus;
static volatile int _iicMode;
static int _iicPt;
//====================================================
// 函数定义区
//====================================================
void __irq IicInt(void);
void Wr24C04(U32 slvAddr,U32 addr,U8 data);
void Rd24C04(U32 slvAddr,U32 addr,U8 *data);
//====================================================================
// 功 能 : S3C2440 IIC-bus Master Tx/Rx mode Test Program
// (Interrupt / Non Interrupt (Polling))
//====================================================================
//******************[ Test_Iic ]**************************************
void Test_Iic(void)
{
unsigned int i,j,save_E,save_PE;
static U8 data[256];
Uart_Printf("[ IIC Test(Interrupt) using AT24C04 ]\n");
save_E = rGPECON;
save_PE = rGPEUP;
rGPEUP |= 0xc000; //Pull-up disable
rGPECON |= 0xa0000000; //GPE15:IICSDA , GPE14:IICSCL
pISR_IIC = (unsigned)IicInt;
rINTMSK &= ~(BIT_IIC);
//Enable ACK, Prescaler IICCLK=PCLK/16, Enable interrupt, Transmit clock value Tx clock=IICCLK/16
// If PCLK 50.7MHz, IICCLK = 3.17MHz, Tx Clock = 0.198MHz
rIICCON = (1<<7) | (0<<6) | (1<<5) | (0xf);
rIICADD = 0x10; //2440 slave address = [7:1]
rIICSTAT = 0x10; //IIC bus data output enable(Rx/Tx)
rIICLC = (1<<2)|(1); // Filter enable, 15 clocks SDA output delay added by junon
Uart_Printf("Write test data into AT24C04\n");
for(i=0;i<256;i++)
Wr24C04(0xa0,(U8)i,i);
for(i=0;i<256;i++)
data[i] = 0;
Uart_Printf("Read test data from AT24C04\n");
for(i=0;i<256;i++)
Rd24C04(0xa0,(U8)i,&(data[i]));
//Line changed 0 ~ f
for(i=0;i<16;i++)
{
for(j=0;j<16;j++)
Uart_Printf("%2x ",data[i*16+j]);
Uart_Printf("\n");
}
rINTMSK |= BIT_IIC;
rGPEUP = save_PE;
rGPECON = save_E;
}
//*************************[ Wr24C04 ]****************************
void Wr24C04(U32 slvAddr,U32 addr,U8 data)
{
_iicMode = WRDATA;
_iicPt = 0;
_iicData[0] = (U8)addr;
_iicData[1] = data;
_iicDataCount = 2;
rIICDS = slvAddr; //0xa0
rIICSTAT = 0xf0; //MasTx,Start
//Clearing the pending bit isn't needed because the pending bit has been cleared.
while(_iicDataCount!=-1);
_iicMode = POLLACK;
while(1)
{
rIICDS = slvAddr;
_iicStatus = 0x100;
rIICSTAT = 0xf0; //MasTx,Start
rIICCON = 0xaf; //Resumes IIC operation.
while(_iicStatus==0x100);
if(!(_iicStatus&0x1))
break; //When ACK is received
}
rIICSTAT = 0xd0; //Stop MasTx condition
rIICCON = 0xaf; //Resumes IIC operation.
Delay(1); //Wait until stop condtion is in effect.
//Write is completed.
}
//**********************[ Rd24C04 ] ***********************************
void Rd24C04(U32 slvAddr,U32 addr,U8 *data)
{
_iicMode = SETRDADDR;
_iicPt = 0;
_iicData[0] = (U8)addr;
_iicDataCount = 1;
rIICDS = slvAddr;
rIICSTAT = 0xf0; //MasTx,Start
//Clearing the pending bit isn't needed because the pending bit has been cleared.
while(_iicDataCount!=-1);
_iicMode = RDDATA;
_iicPt = 0;
_iicDataCount = 1;
rIICDS = slvAddr;
rIICSTAT = 0xb0; //MasRx,Start
rIICCON = 0xaf; //Resumes IIC operation.
while(_iicDataCount!=-1);
*data = _iicData[1];
}
//-------------------------------------------------------------------------
void __irq IicInt(void)
{
U32 iicSt,i;
rSRCPND = BIT_IIC; //Clear pending bit
rINTPND = BIT_IIC;
iicSt = rIICSTAT;
if(iicSt & 0x8){} //When bus arbitration is failed.
if(iicSt & 0x4){} //When a slave address is matched with IICADD
if(iicSt & 0x2){} //When a slave address is 0000000b
if(iicSt & 0x1){} //When ACK isn't received
switch(_iicMode)
{
case POLLACK:
_iicStatus = iicSt;
break;
case RDDATA:
if((_iicDataCount--)==0)
{
_iicData[_iicPt++] = rIICDS;
rIICSTAT = 0x90; //Stop MasRx condition
rIICCON = 0xaf; //Resumes IIC operation.
Delay(1); //Wait until stop condtion is in effect.
//Too long time...
//The pending bit will not be set after issuing stop condition.
break;
}
_iicData[_iicPt++] = rIICDS; //The last data has to be read with no ack.
if((_iicDataCount)==0)
rIICCON = 0x2f; //Resumes IIC operation with NOACK.
else
rIICCON = 0xaf; //Resumes IIC operation with ACK
break;
case WRDATA:
if((_iicDataCount--)==0)
{
rIICSTAT = 0xd0; //Stop MasTx condition
rIICCON = 0xaf; //Resumes IIC operation.
Delay(1); //Wait until stop condtion is in effect.
//The pending bit will not be set after issuing stop condition.
break;
}
rIICDS = _iicData[_iicPt++]; //_iicData[0] has dummy.
for(i=0;i<10;i++); //for setup time until rising edge of IICSCL
rIICCON = 0xaf; //resumes IIC operation.
break;
case SETRDADDR:
// Uart_Printf("[ S%d ]",_iicDataCount);
if((_iicDataCount--)==0)
break; //IIC operation is stopped because of IICCON[4]
rIICDS = _iicData[_iicPt++];
for(i=0;i<10;i++); //For setup time until rising edge of IICSCL
rIICCON = 0xaf; //Resumes IIC operation.
break;
default:
break;
}
}
void Main(void)
{
memcpy((unsigned char *)0x0,(unsigned char *)0x30000000,0x1000);
SetSysFclk(FCLK_400M); //设置系统时钟 400M
ChangeClockDivider(2, 1); //设置分频 1：4：8
CalcBusClk(); //计算总线频
Uart_Select(0);
Uart_Init(0, 115200);
Test_Iic();
while(1);
}
s3c2440的IIC 读写AT24C04驱动源码
IIC.rar
