音频uda1341驱动移植

      1、将s3c2410_uda1341.c拷贝到sound/oss下

      2、修改sound/oss/Kconfig

       添加

       config S3C2410_SND_UDA1341

       tristate "S3C2410 UDA1341 driver(S3C2410)"

       depends on SOUND_PRIME!=n && SOUND && ARM && ARCH_SMDK2410

       3、修改sound/oss/Makefile

       添加

       obj-$(CONFIG_S3C2410_SND_UDA1341) += s3c2410-uda1341.o

       4、修改arch/arm/plat-s3c24xx/dma.c

       将函数s3c2410_dma_enqueue中

       s3c2410_dma_ctrl(chan->number, S3C2410_DMAOP_START);

       修改为

       s3c2410_dma_ctrl(channel, S3C2410_DMAOP_START);

       或

       s3c2410_dma_ctrl(chan->number ｜ DMACH_LOW_LEVEL, S3C2410_DMAOP_START);

       5、make menuconfig 配置支持音频驱动

       Device Drivers  ---> 

              Sound  --->

                     <*> Sound card support 

                            Open Sound System  --->

                                   <*> Open Sound System (DEPRECATED)

                                   <*>   S3C2410 UDA1341 driver(S3C2410)

       6、然后make zImage。

       7、拷贝zImage到tftpboot下

       8、系统启动以后会在dev目录下产生dsp设备节点

       文件系统没有支持udev或mdev的话就必须进行下面步骤

       mknod dev/dsp c 14 3

注：在此给出s3c2410_uda1341.c源码：

/*
 *this program suit for linux kernel 2.6.22 20090310
 */
#include
#include
#include
#include
#include
#include
#include
#include
/* add by lfc */
#include
#include
/* end add */
#include

#include
#include
#include
#include

#include
#include
#include

//这里我自己改的
//#include
#include

#define PFX "s3c2410-uda1341-superlp: "

#define RESSIZE(ressource) (((ressource)->end - (ressource)->start)+1)

#define MAX_DMA_CHANNELS 0

/* The S3C2410 has four internal DMA channels. */

#define MAX_S3C2410_DMA_CHANNELS S3C2410_DMA_CHANNELS

#define DMA_CH1 DMACH_I2S_IN
#define DMA_CH2 DMACH_I2S_OUT

#define DMA_BUF_WR 1
#define DMA_BUF_RD 0

#define dma_wrreg(chan, reg, val) writel((val), (chan)->regs + (reg))

/************************* add by lfc **************************/
#define fIISPSR_A Fld(5, 5) /* Prescaler Control A */
#define IISPSR_A(x) FInsrt((x), fIISPSR_A)
#define fIISPSR_B Fld(5, 0) /* Prescaler Control B */
#define IISPSR_B(x) FInsrt((x), fIISPSR_B)
/**************************** end add **************************/

static struct clk *iis_clock;
static void __iomem *iis_base;

static struct s3c2410_dma_client s3c2410iis_dma_out= {
.name = "I2SSDO",
};

static struct s3c2410_dma_client s3c2410iis_dma_in = {
.name = "I2SSDI",
};

//#define DEBUG

#ifdef DEBUG
#define DPRINTK printk
#else
#define DPRINTK( x... )
#endif

static void init_s3c2410_iis_bus_rx(void);
static void init_s3c2410_iis_bus_tx(void);

#define DEF_VOLUME 80

/* UDA1341 Register bits */
#define UDA1341_ADDR 0x14

#define UDA1341_REG_DATA0 (UDA1341_ADDR + 0)
#define UDA1341_REG_STATUS (UDA1341_ADDR + 2)

/* status control */
#define STAT0 (0x00)
#define STAT0_RST (1 << 6)
#define STAT0_SC_MASK (3 << 4)
#define STAT0_SC_512FS (0 << 4)
#define STAT0_SC_384FS (1 << 4)
#define STAT0_SC_256FS (2 << 4)
#define STAT0_IF_MASK (7 << 1)
#define STAT0_IF_I2S (0 << 1)
#define STAT0_IF_LSB16 (1 << 1)
#define STAT0_IF_LSB18 (2 << 1)
#define STAT0_IF_LSB20 (3 << 1)
#define STAT0_IF_MSB (4 << 1)
#define STAT0_IF_LSB16MSB (5 << 1)
#define STAT0_IF_LSB18MSB (6 << 1)
#define STAT0_IF_LSB20MSB (7 << 1)
#define STAT0_DC_FILTER (1 << 0)
#define STAT0_DC_NO_FILTER (0 << 0)

#define STAT1 (0x80)
#define STAT1_DAC_GAIN (1 << 6) /* gain of DAC */
#define STAT1_ADC_GAIN (1 << 5) /* gain of ADC */
#define STAT1_ADC_POL (1 << 4) /* polarity of ADC */
#define STAT1_DAC_POL (1 << 3) /* polarity of DAC */
#define STAT1_DBL_SPD (1 << 2) /* double speed playback */
#define STAT1_ADC_ON (1 << 1) /* ADC powered */
#define STAT1_DAC_ON (1 << 0) /* DAC powered */

/* data0 direct control */
#define DATA0 (0x00)
#define DATA0_VOLUME_MASK (0x3f)
#define DATA0_VOLUME(x) (x)

#define DATA1 (0x40)
#define DATA1_BASS(x) ((x) << 2)
#define DATA1_BASS_MASK (15 << 2)
#define DATA1_TREBLE(x) ((x))
#define DATA1_TREBLE_MASK (3)

#define DATA2 (0x80)
#define DATA2_PEAKAFTER (0x1 << 5)
#define DATA2_DEEMP_NONE (0x0 << 3)
#define DATA2_DEEMP_32KHz (0x1 << 3)
#define DATA2_DEEMP_44KHz (0x2 << 3)
#define DATA2_DEEMP_48KHz (0x3 << 3)
#define DATA2_MUTE (0x1 << 2)
#define DATA2_FILTER_FLAT (0x0 << 0)
#define DATA2_FILTER_MIN (0x1 << 0)
#define DATA2_FILTER_MAX (0x3 << 0)
/* data0 extend control */
#define EXTADDR(n) (0xc0 | (n))
#define EXTDATA(d) (0xe0 | (d))

#define EXT0 0
#define EXT0_CH1_GAIN(x) (x)
#define EXT1 1
#define EXT1_CH2_GAIN(x) (x)
#define EXT2 2
#define EXT2_MIC_GAIN_MASK (7 << 2)
#define EXT2_MIC_GAIN(x) ((x) << 2)
#define EXT2_MIXMODE_DOUBLEDIFF (0)
#define EXT2_MIXMODE_CH1 (1)
#define EXT2_MIXMODE_CH2 (2)
#define EXT2_MIXMODE_MIX (3)
#define EXT4 4
#define EXT4_AGC_ENABLE (1 << 4)
#define EXT4_INPUT_GAIN_MASK (3)
#define EXT4_INPUT_GAIN(x) ((x) & 3)
#define EXT5 5
#define EXT5_INPUT_GAIN(x) ((x) >> 2)
#define EXT6 6
#define EXT6_AGC_CONSTANT_MASK (7 << 2)
#define EXT6_AGC_CONSTANT(x) ((x) << 2)
#define EXT6_AGC_LEVEL_MASK (3)
#define EXT6_AGC_LEVEL(x) (x)

#define AUDIO_NAME "UDA1341"
#define AUDIO_NAME_VERBOSE "UDA1341 audio driver"

#define AUDIO_FMT_MASK (AFMT_S16_LE)
#define AUDIO_FMT_DEFAULT (AFMT_S16_LE)

#define AUDIO_CHANNELS_DEFAULT 2
#define AUDIO_RATE_DEFAULT 44100

#define AUDIO_NBFRAGS_DEFAULT 8
#define AUDIO_FRAGSIZE_DEFAULT 8192

#define S_CLOCK_FREQ 384
#define PCM_ABS(a) (a < 0 ? -a : a)

typedef struct {
int size; /* buffer size */
char *start; /* point to actual buffer */
dma_addr_t dma_addr; /* physical buffer address */
struct semaphore sem; /* down before touching the buffer */
int master; /* owner for buffer allocation, contain size when true */
} audio_buf_t;

typedef struct {
audio_buf_t *buffers; /* pointer to audio buffer structures */
audio_buf_t *buf; /* current buffer used by read/write */
u_int buf_idx; /* index for the pointer above */
u_int fragsize; /* fragment i.e. buffer size */
u_int nbfrags; /* nbr of fragments */
dmach_t dma_ch; /* DMA channel (channel2 for audio) */
u_int dma_ok;
} audio_stream_t;

/*
* 驱动对于内存是这样使用的：
* 把buffers所指向的内存分成nbfragsxfragsize的空间(每一块的大小为fragsize，供分成nbfrags块)
* buf指向当前所使用的内存块，buf_idx只是内存块序号
*/

static audio_stream_t output_stream;
static audio_stream_t input_stream; /* input */

#define NEXT_BUF(_s_,_b_) { \
(_s_)->_b_##_idx++; \
(_s_)->_b_##_idx %= (_s_)->nbfrags; \
(_s_)->_b_ = (_s_)->buffers + (_s_)->_b_##_idx; }

static u_int audio_rate;
static int audio_channels;
static int audio_fmt;
static u_int audio_fragsize;
static u_int audio_nbfrags;

static int audio_rd_refcount;
static int audio_wr_refcount;
#define audio_active (audio_rd_refcount | audio_wr_refcount)

static int audio_dev_dsp;
static int audio_dev_mixer;
static int audio_mix_modcnt;

static int uda1341_volume;
//static u8 uda_sampling;
static int uda1341_boost;
static int mixer_igain=0x4; /* -6db*/

static void uda1341_l3_address(u8 data)
{
int i;
unsigned long flags;

local_irq_save(flags);

// write_gpio_bit(GPIO_L3MODE, 0);
s3c2410_gpio_setpin(S3C2410_GPB2,0);
// write_gpio_bit(GPIO_L3CLOCK, 1);
s3c2410_gpio_setpin(S3C2410_GPB4,1);
udelay(1);

for (i = 0; i < 8; i++) {
if (data & 0x1) {
s3c2410_gpio_setpin(S3C2410_GPB4,0);
s3c2410_gpio_setpin(S3C2410_GPB3,1);
udelay(1);
s3c2410_gpio_setpin(S3C2410_GPB4,1);
} else {
s3c2410_gpio_setpin(S3C2410_GPB4,0);
s3c2410_gpio_setpin(S3C2410_GPB3,0);
udelay(1);
s3c2410_gpio_setpin(S3C2410_GPB4,1);
}
data >>= 1;
}

s3c2410_gpio_setpin(S3C2410_GPB2,1);
s3c2410_gpio_setpin(S3C2410_GPB4,1);
local_irq_restore(flags);
}

static void uda1341_l3_data(u8 data)
{
int i;
unsigned long flags;

local_irq_save(flags);
udelay(1);

for (i = 0; i < 8; i++) {
if (data & 0x1) {
s3c2410_gpio_setpin(S3C2410_GPB4,0);
s3c2410_gpio_setpin(S3C2410_GPB3,1);
udelay(1);
s3c2410_gpio_setpin(S3C2410_GPB4,1);
} else {
s3c2410_gpio_setpin(S3C2410_GPB4,0);
s3c2410_gpio_setpin(S3C2410_GPB3,0);
udelay(1);
s3c2410_gpio_setpin(S3C2410_GPB4,1);
}

data >>= 1;
}

local_irq_restore(flags);
}

static void audio_clear_buf(audio_stream_t * s)
{
DPRINTK("audio_clear_buf\n");

if(s->dma_ok)
s3c2410_dma_ctrl(s->dma_ch, S3C2410_DMAOP_FLUSH);

if (s->buffers) {
int frag;

for (frag = 0; frag < s->nbfrags; frag++) {
if (!s->buffers[frag].master)
continue;
dma_free_coherent(NULL,
s->buffers[frag].master,
s->buffers[frag].start,
s->buffers[frag].dma_addr);
}
kfree(s->buffers);
s->buffers = NULL;
}

s->buf_idx = 0;
s->buf = NULL;
}

static int audio_setup_buf(audio_stream_t * s)
{
int frag;
int dmasize = 0;
char *dmabuf = 0;
dma_addr_t dmaphys = 0;

DPRINTK("audio_setup_buf\n");
if (s->buffers)
return -EBUSY;

s->nbfrags = audio_nbfrags;
s->fragsize = audio_fragsize;

s->buffers = (audio_buf_t *)
kmalloc(sizeof(audio_buf_t) * s->nbfrags, GFP_KERNEL);
if (!s->buffers)
goto err;
memset(s->buffers, 0, sizeof(audio_buf_t) * s->nbfrags);

for (frag = 0; frag < s->nbfrags; frag++) {
audio_buf_t *b = &s->buffers[frag];

if (!dmasize) {
dmasize = (s->nbfrags - frag) * s->fragsize;
do {
dmabuf = dma_alloc_coherent(NULL, dmasize, &dmaphys, GFP_KERNEL|GFP_DMA);
if (!dmabuf)
dmasize -= s->fragsize;
} while (!dmabuf && dmasize);
if (!dmabuf)
goto err;
b->master = dmasize;
}

b->start = dmabuf;
b->dma_addr = dmaphys;
sema_init(&b->sem, 1);
DPRINTK("buf %d: start %p dma %d\n", frag, b->start, b->dma_addr);

dmabuf += s->fragsize;
dmaphys += s->fragsize;
dmasize -= s->fragsize;
}

s->buf_idx = 0;
s->buf = &s->buffers[0];
return 0;

err:
printk(AUDIO_NAME ": unable to allocate audio memory\n ");
audio_clear_buf(s);
return -ENOMEM;
}

static void audio_dmaout_done_callback(struct s3c2410_dma_chan *ch, void *buf, int size,
enum s3c2410_dma_buffresult result)
{
audio_buf_t *b = (audio_buf_t *) buf;

DPRINTK("audio_dmaout_done_callback\n");

up(&b->sem);
wake_up(&b->sem.wait);
}

static void audio_dmain_done_callback(struct s3c2410_dma_chan *ch, void *buf, int size,
enum s3c2410_dma_buffresult result)
{
audio_buf_t *b = (audio_buf_t *) buf;

DPRINTK("audio_dmain_done_callback\n");

b->size = size;
up(&b->sem);
wake_up(&b->sem.wait);
}

/* using when write */
static int audio_sync(struct file *file)
{
audio_stream_t *s = &output_stream;
audio_buf_t *b = s->buf;

DPRINTK("audio_sync\n");

if (!s->buffers)
return 0;

if (b->size != 0) {
down(&b->sem);
s3c2410_dma_enqueue(s->dma_ch, (void *) b, b->dma_addr, b->size);
b->size = 0;
NEXT_BUF(s, buf);
}

b = s->buffers + ((s->nbfrags + s->buf_idx - 1) % s->nbfrags);
if (down_interruptible(&b->sem))
return -EINTR;
up(&b->sem);

return 0;
}

static inline int copy_from_user_mono_stereo(char *to, const char *from, int count)
{
u_int *dst = (u_int *)to;
const char *end = from + count;

DPRINTK("copy_from_user_mono_stereo\n");

if (access_ok(VERIFY_READ, from, count))
return -EFAULT;

if ((int)from & 0x2) {
u_int v;
__get_user(v, (const u_short *)from); from += 2;
*dst++ = v | (v << 16);
}

while (from < end-2) {
u_int v, x, y;
__get_user(v, (const u_int *)from); from += 4;
x = v << 16;
x |= x >> 16;
y = v >> 16;
y |= y << 16;
*dst++ = x;
*dst++ = y;
}

if (from < end) {
u_int v;
__get_user(v, (const u_short *)from);
*dst = v | (v << 16);
}

return 0;
}

static ssize_t smdk2410_audio_write(struct file *file, const char *buffer,
size_t count, loff_t * ppos)
{
const char *buffer0 = buffer;
audio_stream_t *s = &output_stream;
int chunksize, ret = 0;

DPRINTK("audio_write : start count=%d\n", count);

switch (file->f_flags & O_ACCMODE) {
case O_WRONLY:
case O_RDWR:
break;
default:
DPRINTK("EPERM\n");
return -EPERM;
}

if (!s->buffers && audio_setup_buf(s)){
DPRINTK("ENOMEM\n");
return -ENOMEM;
}

count &= ~0x03;

while (count > 0) {
audio_buf_t *b = s->buf;

if (file->f_flags & O_NONBLOCK) {
ret = -EAGAIN;
if (down_trylock(&b->sem)){
DPRINTK("down_trylock error\n");
break;
}
} else {
ret = -ERESTARTSYS;
if (down_interruptible(&b->sem)){
DPRINTK("down_interruptible error\n");
break;
}
}

if (audio_channels == 2) {
chunksize = s->fragsize - b->size;//当前内存块可供使用空间
if (chunksize > count)
chunksize = count;
DPRINTK("write %d to %d\n", chunksize, s->buf_idx);
if (copy_from_user(b->start + b->size, buffer, chunksize)) {
DPRINTK("copy_from_user error\n");
up(&b->sem);
return -EFAULT;
}
b->size += chunksize;//更新当前内存块的使用情况
} else {
chunksize = (s->fragsize - b->size) >> 1;

if (chunksize > count)
chunksize = count;
DPRINTK("write %d to %d\n", chunksize*2, s->buf_idx);
if (copy_from_user_mono_stereo(b->start + b->size, buffer, chunksize)) {
DPRINTK("copy_from_user_mono_stereo error\n");
up(&b->sem);
return -EFAULT;
}
b->size += chunksize*2;
}

buffer += chunksize;
count -= chunksize;
if (b->size < s->fragsize) {
up(&b->sem);
break;
}
/* 填满一块内存就交给dma去处理 */
if((ret = s3c2410_dma_enqueue(s->dma_ch, (void *) b, b->dma_addr, b->size))) {
printk("dma enqueue failed.\n");
return ret;
}
/* 把内存块加入dma队列后继续填写下一内存块 */
b->size = 0;
NEXT_BUF(s, buf);
}

if ((buffer - buffer0))
ret = buffer - buffer0;//返回已传输的字节数

DPRINTK("audio_write : end count=%d\n\n", ret);

return ret;
}

static ssize_t smdk2410_audio_read(struct file *file, char *buffer,
size_t count, loff_t * ppos)
{
const char *buffer0 = buffer;
audio_stream_t *s = &input_stream;
int chunksize, ret = 0;

DPRINTK("audio_read: count=%d\n", count);
/*
if (ppos != &file->f_pos)
return -ESPIPE;
*/
if (!s->buffers) {
int i;

if (audio_setup_buf(s))
return -ENOMEM;

for (i = 0; i < s->nbfrags; i++) {
audio_buf_t *b = s->buf;
down(&b->sem);
s3c2410_dma_enqueue(s->dma_ch, (void *) b, b->dma_addr, s->fragsize);
NEXT_BUF(s, buf);
}
}

while (count > 0) {
audio_buf_t *b = s->buf;

/* Wait for a buffer to become full */
if (file->f_flags & O_NONBLOCK) {
ret = -EAGAIN;
if (down_trylock(&b->sem))
break;
} else {
ret = -ERESTARTSYS;
if (down_interruptible(&b->sem))
break;
}

chunksize = b->size;
if (chunksize > count)
chunksize = count;
DPRINTK("read %d from %d\n", chunksize, s->buf_idx);
if (copy_to_user(buffer, b->start + s->fragsize - b->size,
chunksize)) {
up(&b->sem);
return -EFAULT;
}

b->size -= chunksize;

buffer += chunksize;
count -= chunksize;
if (b->size > 0) {
up(&b->sem);
break;
}

/* Make current buffer available for DMA again */
s3c2410_dma_enqueue(s->dma_ch, (void *) b, b->dma_addr, s->fragsize);

NEXT_BUF(s, buf);
}

if ((buffer - buffer0))
ret = buffer - buffer0;

// DPRINTK("audio_read: return=%d\n", ret);

return ret;
}

static unsigned int smdk2410_audio_poll(struct file *file,struct poll_table_struct *wait)
{
unsigned int mask = 0;
int i;

DPRINTK("audio_poll(): mode=%s\n",
(file->f_mode & FMODE_WRITE) ? "w" : "");

if (file->f_mode & FMODE_READ) {
if (!input_stream.buffers && audio_setup_buf(&input_stream))
return -ENOMEM;
poll_wait(file, &input_stream.buf->sem.wait, wait);

for (i = 0; i < input_stream.nbfrags; i++) {
if (atomic_read(&input_stream.buffers[i].sem.count) > 0){
mask |= POLLIN | POLLWRNORM;
break;
}
}
}

if (file->f_mode & FMODE_WRITE) {
if (!output_stream.buffers && audio_setup_buf(&output_stream))
return -ENOMEM;
poll_wait(file, &output_stream.buf->sem.wait, wait);

for (i = 0; i < output_stream.nbfrags; i++) {
if (atomic_read(&output_stream.buffers[i].sem.count) > 0){
mask |= POLLOUT | POLLWRNORM;
break;
}
}
}

DPRINTK("audio_poll() returned mask of %s\n",(mask & POLLOUT) ? "w" : "");

return mask;
}

static loff_t smdk2410_audio_llseek(struct file *file, loff_t offset,
int origin)
{
DPRINTK("smdk2410_audio_llseek\n");
return -ESPIPE;
}

static int smdk2410_mixer_ioctl(struct inode *inode, struct file *file,
unsigned int cmd, unsigned long arg)
{
int ret;
long val = 0;

DPRINTK("smdk2410_mixer_ioctl\n");

switch (cmd) {
case SOUND_MIXER_INFO:
{
mixer_info info;
strncpy(info.id, "UDA1341", sizeof(info.id));
strncpy(info.name,"Philips UDA1341", sizeof(info.name));
info.modify_counter = audio_mix_modcnt;
return copy_to_user((void *)arg, &info, sizeof(info));
}

case SOUND_OLD_MIXER_INFO:
{
_old_mixer_info info;
strncpy(info.id, "UDA1341", sizeof(info.id));
strncpy(info.name,"Philips UDA1341", sizeof(info.name));
return copy_to_user((void *)arg, &info, sizeof(info));
}

case SOUND_MIXER_READ_STEREODEVS:
return put_user(0, (long *) arg);

case SOUND_MIXER_READ_CAPS:
val = SOUND_CAP_EXCL_INPUT;
return put_user(val, (long *) arg);

case SOUND_MIXER_WRITE_VOLUME:
ret = get_user(val, (long *) arg);
if (ret)
return ret;
uda1341_volume = 63 - (((val & 0xff) + 1) * 63) / 100;
uda1341_l3_address(UDA1341_REG_DATA0);
uda1341_l3_data(uda1341_volume);
break;

case SOUND_MIXER_READ_VOLUME:
val = ((63 - uda1341_volume) * 100) / 63;
val |= val << 8;
return put_user(val, (long *) arg);

case SOUND_MIXER_READ_IGAIN:
val = ((31- mixer_igain) * 100) / 31;
return put_user(val, (int *) arg);

case SOUND_MIXER_WRITE_IGAIN:
ret = get_user(val, (int *) arg);
if (ret)
return ret;
mixer_igain = 31 - (val * 31 / 100);
/* use mixer gain channel 1*/
uda1341_l3_address(UDA1341_REG_DATA0);
uda1341_l3_data(EXTADDR(EXT0));
uda1341_l3_data(EXTDATA(EXT0_CH1_GAIN(mixer_igain)));
break;

default:
DPRINTK("mixer ioctl %u unknown\n", cmd);
return -ENOSYS;
}

audio_mix_modcnt++;
return 0;
}

static int iispsr_value(int s_bit_clock, int sample_rate)
{
int i, prescaler = 0;
unsigned long tmpval;
unsigned long tmpval384;
unsigned long tmpval384min = 0xffff;

tmpval384 = clk_get_rate(iis_clock) / s_bit_clock;

for (i = 0; i < 32; i++) {
tmpval = tmpval384/(i+1);
if (PCM_ABS((sample_rate - tmpval)) < tmpval384min) {
tmpval384min = PCM_ABS((sample_rate - tmpval));
prescaler = i;
}
}

DPRINTK("prescaler = %d\n", prescaler);

return prescaler;
}

static long audio_set_dsp_speed(long val)
{
unsigned int prescaler;
prescaler=(IISPSR_A(iispsr_value(S_CLOCK_FREQ, val))
| IISPSR_B(iispsr_value(S_CLOCK_FREQ, val)));
writel(prescaler, iis_base + S3C2410_IISPSR);

printk(PFX "audio_set_dsp_speed:%ld prescaler:%i\n",val,prescaler);
return (audio_rate = val);
}

static int smdk2410_audio_ioctl(struct inode *inode, struct file *file,
uint cmd, ulong arg)
{
long val;

DPRINTK("smdk2410_audio_ioctl\n");

switch (cmd) {
case SNDCTL_DSP_SETFMT:
get_user(val, (long *) arg);
if (val & AUDIO_FMT_MASK) {
audio_fmt = val;
break;
} else
return -EINVAL;

case SNDCTL_DSP_CHANNELS:
case SNDCTL_DSP_STEREO:
get_user(val, (long *) arg);
if (cmd == SNDCTL_DSP_STEREO)
val = val ? 2 : 1;
if (val != 1 && val != 2)
return -EINVAL;
DPRINTK("audio_channels set to %d\n", val);
audio_channels = val;
break;

case SOUND_PCM_READ_CHANNELS:
DPRINTK("audio_channels is %d\n", audio_channels);
put_user(audio_channels, (long *) arg);
break;

case SNDCTL_DSP_SPEED:
get_user(val, (long *) arg);
val = audio_set_dsp_speed(val);
if (val < 0)
return -EINVAL;
put_user(val, (long *) arg);
break;

case SOUND_PCM_READ_RATE:
put_user(audio_rate, (long *) arg);
break;

case SNDCTL_DSP_GETFMTS:
put_user(AUDIO_FMT_MASK, (long *) arg);
break;

case SNDCTL_DSP_GETBLKSIZE:
if(file->f_mode & FMODE_WRITE)
return put_user(audio_fragsize, (long *) arg);
else
return put_user(audio_fragsize, (int *) arg);

case SNDCTL_DSP_SETFRAGMENT:
if (file->f_mode & FMODE_WRITE) {
if (output_stream.buffers)
return -EBUSY;
get_user(val, (long *) arg);
audio_fragsize = 1 << (val & 0xFFFF);
if (audio_fragsize < 16)
audio_fragsize = 16;
if (audio_fragsize > 16384)
audio_fragsize = 16384;
audio_nbfrags = (val >> 16) & 0x7FFF;
if (audio_nbfrags < 2)
audio_nbfrags = 2;
if (audio_nbfrags * audio_fragsize > 128 * 1024)
audio_nbfrags = 128 * 1024 / audio_fragsize;
if (audio_setup_buf(&output_stream))
return -ENOMEM;

}
if (file->f_mode & FMODE_READ) {
if (input_stream.buffers)
return -EBUSY;
get_user(val, (int *) arg);
audio_fragsize = 1 << (val & 0xFFFF);
if (audio_fragsize < 16)
audio_fragsize = 16;
if (audio_fragsize > 16384)
audio_fragsize = 16384;
audio_nbfrags = (val >> 16) & 0x7FFF;
if (audio_nbfrags < 2)
audio_nbfrags = 2;
if (audio_nbfrags * audio_fragsize > 128 * 1024)
audio_nbfrags = 128 * 1024 / audio_fragsize;
if (audio_setup_buf(&input_stream))
return -ENOMEM;

}
break;

case SNDCTL_DSP_SYNC:
return audio_sync(file);

case SNDCTL_DSP_GETOSPACE:
{
audio_stream_t *s = &output_stream;
audio_buf_info *inf = (audio_buf_info *) arg;
int err = access_ok(VERIFY_WRITE, inf, sizeof(*inf));
int i;
int frags = 0, bytes = 0;

if (err)
return err;
for (i = 0; i < s->nbfrags; i++) {
if (atomic_read(&s->buffers[i].sem.count) > 0) {
if (s->buffers[i].size == 0) frags++;
bytes += s->fragsize - s->buffers[i].size;
}
}
put_user(frags, &inf->fragments);
put_user(s->nbfrags, &inf->fragstotal);
put_user(s->fragsize, &inf->fragsize);
put_user(bytes, &inf->bytes);
break;
}

case SNDCTL_DSP_GETISPACE:
{
audio_stream_t *s = &input_stream;
audio_buf_info *inf = (audio_buf_info *) arg;
int err = access_ok(VERIFY_WRITE, inf, sizeof(*inf));
int i;
int frags = 0, bytes = 0;

if (!(file->f_mode & FMODE_READ))
return -EINVAL;

if (err)
return err;
for(i = 0; i < s->nbfrags; i++){
if (atomic_read(&s->buffers[i].sem.count) > 0)
{
if (s->buffers[i].size == s->fragsize)
frags++;
bytes += s->buffers[i].size;
}
}
put_user(frags, &inf->fragments);
put_user(s->nbfrags, &inf->fragstotal);
put_user(s->fragsize, &inf->fragsize);
put_user(bytes, &inf->bytes);
break;
}

case SNDCTL_DSP_RESET:
if (file->f_mode & FMODE_READ) {
audio_clear_buf(&input_stream);
}
if (file->f_mode & FMODE_WRITE) {
audio_clear_buf(&output_stream);
}
return 0;

case SNDCTL_DSP_NONBLOCK:
file->f_flags |= O_NONBLOCK;
return 0;

case SNDCTL_DSP_POST:
case SNDCTL_DSP_SUBDIVIDE:
case SNDCTL_DSP_GETCAPS:
case SNDCTL_DSP_GETTRIGGER:
case SNDCTL_DSP_SETTRIGGER:
case SNDCTL_DSP_GETIPTR:
case SNDCTL_DSP_GETOPTR:
case SNDCTL_DSP_MAPINBUF:
case SNDCTL_DSP_MAPOUTBUF:
case SNDCTL_DSP_SETSYNCRO:
case SNDCTL_DSP_SETDUPLEX:
return -ENOSYS;
default:
return smdk2410_mixer_ioctl(inode, file, cmd, arg);
}

return 0;
}

static int smdk2410_audio_open(struct inode *inode, struct file *file)
{
int cold = !audio_active;

DPRINTK("audio_open\n");
if ((file->f_flags & O_ACCMODE) == O_RDONLY) {
if (audio_rd_refcount || audio_wr_refcount)
return -EBUSY;
audio_rd_refcount++;
} else if ((file->f_flags & O_ACCMODE) == O_WRONLY) {
if (audio_wr_refcount)
return -EBUSY;
audio_wr_refcount++;
} else if ((file->f_flags & O_ACCMODE) == O_RDWR) {
if (audio_rd_refcount || audio_wr_refcount)
return -EBUSY;
audio_rd_refcount++;
audio_wr_refcount++;
} else
return -EINVAL;

if (cold) {
audio_rate = AUDIO_RATE_DEFAULT;
audio_channels = AUDIO_CHANNELS_DEFAULT;
audio_fragsize = AUDIO_FRAGSIZE_DEFAULT;
audio_nbfrags = AUDIO_NBFRAGS_DEFAULT;
if ((file->f_mode & FMODE_WRITE)){
init_s3c2410_iis_bus_tx();
audio_clear_buf(&output_stream);
}
if ((file->f_mode & FMODE_READ)){
init_s3c2410_iis_bus_rx();
audio_clear_buf(&input_stream);
}
}
return 0;
}

static int smdk2410_mixer_open(struct inode *inode, struct file *file)
{
DPRINTK("smdk2410_mixer_open\n");
return 0;
}

static int smdk2410_audio_release(struct inode *inode, struct file *file)
{
DPRINTK("audio_release\n");

if (file->f_mode & FMODE_READ) {
if (audio_rd_refcount == 1)
audio_clear_buf(&input_stream);
audio_rd_refcount = 0;
}

if(file->f_mode & FMODE_WRITE) {
if (audio_wr_refcount == 1) {
audio_sync(file);
audio_clear_buf(&output_stream);
audio_wr_refcount = 0;
}
}

return 0;
}

static int smdk2410_mixer_release(struct inode *inode, struct file *file)
{
DPRINTK("smdk2410_mixer_release\n");
return 0;
}

static struct file_operations smdk2410_audio_fops = {
llseek: smdk2410_audio_llseek,
write: smdk2410_audio_write,
read: smdk2410_audio_read,
poll: smdk2410_audio_poll,
ioctl: smdk2410_audio_ioctl,
open: smdk2410_audio_open,
release: smdk2410_audio_release
};

static struct file_operations smdk2410_mixer_fops = {
ioctl: smdk2410_mixer_ioctl,
open: smdk2410_mixer_open,
release: smdk2410_mixer_release
};

static void init_uda1341(void)
{

/* GPB 4: L3CLOCK */
/* GPB 3: L3DATA */
/* GPB 2: L3MODE */

unsigned long flags;

DPRINTK("init_uda1341\n");

uda1341_volume = 62 - ((DEF_VOLUME * 61) / 100);
uda1341_boost = 0;
// uda_sampling = DATA2_DEEMP_NONE;
// uda_sampling &= ~(DATA2_MUTE);

local_irq_save(flags);

s3c2410_gpio_setpin(S3C2410_GPB2,1);//L3MODE=1
s3c2410_gpio_setpin(S3C2410_GPB4,1);//L3CLOCK=1
local_irq_restore(flags);

uda1341_l3_address(UDA1341_REG_STATUS);
uda1341_l3_data(0x40 | STAT0_SC_384FS | STAT0_IF_MSB|STAT0_DC_FILTER); // reset uda1341
uda1341_l3_data(STAT1 | STAT1_ADC_ON | STAT1_DAC_ON);

uda1341_l3_address(UDA1341_REG_DATA0);
// uda1341_l3_data(DATA0 |DATA0_VOLUME(0x0)); // maximum volume
uda1341_l3_data(DATA0 | DATA0_VOLUME(uda1341_volume));//lfc
uda1341_l3_data(DATA1 |DATA1_BASS(uda1341_boost)| DATA1_TREBLE(0));
uda1341_l3_data((DATA2 |DATA2_DEEMP_NONE) &~(DATA2_MUTE));
uda1341_l3_data(EXTADDR(EXT2));
uda1341_l3_data(EXTDATA(EXT2_MIC_GAIN(0x6)) | EXT2_MIXMODE_CH1);//input channel 1 select(input channel 2 off)

}

static void init_s3c2410_iis_bus(void){
DPRINTK("init_s3c2410_iis_bus\n");
writel(0, iis_base + S3C2410_IISPSR);
writel(0, iis_base + S3C2410_IISCON);
writel(0, iis_base + S3C2410_IISMOD);
writel(0, iis_base + S3C2410_IISFCON);
clk_disable(iis_clock);
}

static void init_s3c2410_iis_bus_rx(void)
{
unsigned int iiscon, iismod, iisfcon;
char *dstr;

DPRINTK("init_s3c2410_iis_bus_rx\n");
//Kill everything...
writel(0, iis_base + S3C2410_IISPSR);
writel(0, iis_base + S3C2410_IISCON);
writel(0, iis_base + S3C2410_IISMOD);
writel(0, iis_base + S3C2410_IISFCON);

clk_enable(iis_clock);

iiscon = iismod = iisfcon = 0;

//Setup basic stuff
iiscon |= S3C2410_IISCON_PSCEN; // Enable prescaler

//iismod |= S3C2410_IISMOD_MASTER; // Set interface to Master Mode
iismod |= S3C2410_IISMOD_LR_LLOW; // Low for left channel
iismod |= S3C2410_IISMOD_MSB; // IIS format
iismod |= S3C2410_IISMOD_16BIT; // Serial data bit/channel is 16 bit
iismod |= S3C2410_IISMOD_384FS; // Master clock freq = 384 fs
iismod |= S3C2410_IISMOD_32FS; // 32 fs

iisfcon|= S3C2410_IISFCON_RXDMA | S3C2410_IISFCON_RXENABLE; //Set RX FIFO acces mode to DMA
//iisfcon|= S3C2410_IISFCON_TXDMA; //Set RX FIFO acces mode to DMA

iiscon |= S3C2410_IISCON_RXDMAEN | S3C2410_IISCON_IISEN; //Enable RX DMA service request
//iiscon |= S3C2410_IISCON_TXIDLE; //Set TX channel idle
iiscon &= (~S3C2410_IISCON_RXIDLE);

iismod |= S3C2410_IISMOD_RXMODE; //Set RX Mode
iismod |= S3C2410_IISMOD_TXMODE;
dstr="RX";
//setup the prescaler
audio_set_dsp_speed(audio_rate);

//iiscon has to be set last - it enables the interface
writel(iismod, iis_base + S3C2410_IISMOD);
writel(iisfcon, iis_base + S3C2410_IISFCON);
writel(iiscon, iis_base + S3C2410_IISCON);
}

static void init_s3c2410_iis_bus_tx(void)
{
unsigned int iiscon, iismod, iisfcon;
char *dstr;

DPRINTK("init_s3c2410_iis_bus_tx\n");
//Kill everything...
writel(0, iis_base + S3C2410_IISPSR);
writel(0, iis_base + S3C2410_IISCON);
writel(0, iis_base + S3C2410_IISMOD);
writel(0, iis_base + S3C2410_IISFCON);

clk_enable(iis_clock);

iiscon = iismod = iisfcon = 0;

//Setup basic stuff
iiscon |= S3C2410_IISCON_PSCEN; // Enable prescaler

//iismod |= S3C2410_IISMOD_MASTER; // Set interface to Master Mode
iismod |= S3C2410_IISMOD_LR_LLOW; // Low for left channel
iismod |= S3C2410_IISMOD_MSB; // MSB format
iismod |= S3C2410_IISMOD_16BIT; // Serial data bit/channel is 16 bit
iismod |= S3C2410_IISMOD_384FS; // Master clock freq = 384 fs
iismod |= S3C2410_IISMOD_32FS; // 32 fs

iisfcon|= S3C2410_IISFCON_RXDMA; //Set RX FIFO acces mode to DMA
iisfcon|= S3C2410_IISFCON_TXDMA; //Set TX FIFO acces mode to DMA

iiscon |= S3C2410_IISCON_TXDMAEN | S3C2410_IISCON_IISEN; //Enable TX DMA service request
//iiscon |= S3C2410_IISCON_RXIDLE; //Set RX channel idle
iiscon &= ~S3C2410_IISCON_TXIDLE;
iismod |= S3C2410_IISMOD_TXMODE; //Set TX Mode
iismod |= S3C2410_IISMOD_RXMODE;
iisfcon|= S3C2410_IISFCON_TXENABLE; //Enable TX Fifo
dstr="TX";

//setup the prescaler
audio_set_dsp_speed(audio_rate);

//iiscon has to be set last - it enables the interface
writel(iismod, iis_base + S3C2410_IISMOD);
writel(iisfcon, iis_base + S3C2410_IISFCON);
writel(iiscon, iis_base + S3C2410_IISCON);
}

static int __init audio_init_dma(audio_stream_t * s, char *desc)
{
int ret ;
enum s3c2410_dmasrc source;
int hwcfg;
unsigned long devaddr;
int dcon;
unsigned int flags = 0;

DPRINTK("audio_init_dma\n");

if(s->dma_ch == DMA_CH2){
source = S3C2410_DMASRC_MEM;
hwcfg = 3;
devaddr = 0x55000010;
dcon = (1<<31) | (0<<30) | (0<<24);
flags = S3C2410_DMAF_AUTOSTART;

ret = s3c2410_dma_request(s->dma_ch, &s3c2410iis_dma_out, NULL);
if (ret) {
printk(KERN_ERR "failed to get dma channel\n");
return ret;
}

s3c2410_dma_devconfig(s->dma_ch, source, hwcfg, devaddr);
s3c2410_dma_config(s->dma_ch, 2, dcon);
s3c2410_dma_set_buffdone_fn(s->dma_ch, audio_dmaout_done_callback);
s3c2410_dma_setflags(s->dma_ch, flags);
s->dma_ok = 1;
return ret;
}
else if(s->dma_ch == DMA_CH1){
source =S3C2410_DMASRC_HW;
hwcfg =3;
devaddr = 0x55000010;
dcon = (1<<31) | (1<<23) | (2<<24);
flags = S3C2410_DMAF_AUTOSTART;

ret = s3c2410_dma_request(s->dma_ch, &s3c2410iis_dma_in, NULL);
if (ret) {
printk(KERN_ERR "failed to get dma channel\n");
return ret;
}

s3c2410_dma_devconfig(s->dma_ch, source, hwcfg, devaddr);
s3c2410_dma_config(s->dma_ch, 2, dcon);
s3c2410_dma_set_buffdone_fn(s->dma_ch, audio_dmain_done_callback);
s3c2410_dma_setflags(s->dma_ch, flags);
s->dma_ok =1;
return ret ;
}
else
return 1;
}

static int audio_clear_dma(audio_stream_t * s,struct s3c2410_dma_client *client)
{
DPRINTK("audio_clear_dma\n");
s3c2410_dma_set_buffdone_fn(s->dma_ch, NULL);
s3c2410_dma_free(s->dma_ch, client);
return 0;
}

static int s3c2410iis_probe(struct platform_device *pdev) {

struct resource *res;
unsigned long flags;
int ret;

DPRINTK("s3c2410iis_probe\n");

res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
if (res == NULL) {
printk(KERN_INFO PFX "failed to get memory region resouce\n");
return -ENOENT;
}

res = request_mem_region(res->start, RESSIZE(res), pdev->name);
if(res == 0){
printk(KERN_INFO PFX "failed to request io memory region.\n");
return -ENOENT;
}

iis_base = ioremap(res->start, RESSIZE(res));
if(iis_base == 0){
printk(KERN_INFO PFX "failed to ioremap() io memory region.\n"); ret = -EINVAL;
goto free_mem_region;
}

iis_clock = clk_get(&pdev->dev, "iis");
if (iis_clock == NULL) {
printk(KERN_INFO PFX "failed to find clock source\n");
return -ENOENT;
}
/**************************modify by lfc*****************************/
clk_enable(iis_clock);
/*****************************end add********************************/
local_irq_save(flags);

/* GPB 4: L3CLOCK, OUTPUT */
s3c2410_gpio_cfgpin(S3C2410_GPB4, S3C2410_GPB4_OUTP);
s3c2410_gpio_pullup(S3C2410_GPB4,1);
/* GPB 3: L3DATA, OUTPUT */
s3c2410_gpio_cfgpin(S3C2410_GPB3,S3C2410_GPB3_OUTP);
/* GPB 2: L3MODE, OUTPUT */
s3c2410_gpio_cfgpin(S3C2410_GPB2,S3C2410_GPB2_OUTP);
s3c2410_gpio_pullup(S3C2410_GPB2,1);
/* GPE 3: I2SSDI */
s3c2410_gpio_cfgpin(S3C2410_GPE3,S3C2410_GPE3_I2SSDI);
s3c2410_gpio_pullup(S3C2410_GPE3,1);
/* GPE 0: I2SLRCK */
s3c2410_gpio_cfgpin(S3C2410_GPE0,S3C2410_GPE0_I2SLRCK);
s3c2410_gpio_pullup(S3C2410_GPE0,1);
/* GPE 1: I2SSCLK */
s3c2410_gpio_cfgpin(S3C2410_GPE1,S3C2410_GPE1_I2SSCLK);
s3c2410_gpio_pullup(S3C2410_GPE1,1);
/* GPE 2: CDCLK */
s3c2410_gpio_cfgpin(S3C2410_GPE2,S3C2410_GPE2_CDCLK);
s3c2410_gpio_pullup(S3C2410_GPE2,1);
/* GPE 4: I2SSDO */
s3c2410_gpio_cfgpin(S3C2410_GPE4,S3C2410_GPE4_I2SSDO);
s3c2410_gpio_pullup(S3C2410_GPE4,1);

local_irq_restore(flags);

init_s3c2410_iis_bus();

init_uda1341();

output_stream.dma_ch = DMA_CH2;

if (audio_init_dma(&output_stream, "UDA1341 out")) {
audio_clear_dma(&output_stream,&s3c2410iis_dma_out);
printk( KERN_WARNING AUDIO_NAME_VERBOSE
": unable to get DMA channels\n" );
return -EBUSY;
}

input_stream.dma_ch = DMA_CH1;

if (audio_init_dma(&input_stream, "UDA1341 in")) {
audio_clear_dma(&input_stream,&s3c2410iis_dma_in);
printk( KERN_WARNING AUDIO_NAME_VERBOSE
": unable to get DMA channels\n" );
return -EBUSY;
}

audio_dev_dsp = register_sound_dsp(&smdk2410_audio_fops, -1);
audio_dev_mixer = register_sound_mixer(&smdk2410_mixer_fops, -1);

printk(AUDIO_NAME_VERBOSE " initialized\n");

free_mem_region:
release_mem_region(res->start, RESSIZE(res));

return 0;
}

static int s3c2410iis_remove(struct platform_device *dev) {
DPRINTK("s3c2410iis_remove\n");

if (iis_clock != NULL){
clk_disable(iis_clock);
clk_put(iis_clock);
iis_clock = NULL;
}

unregister_sound_dsp(audio_dev_dsp);
unregister_sound_mixer(audio_dev_mixer);
audio_clear_dma(&output_stream,&s3c2410iis_dma_out);
audio_clear_dma(&input_stream,&s3c2410iis_dma_in); /* input */
printk(AUDIO_NAME_VERBOSE " unloaded\n");

return 0;
}

static struct platform_driver s3c2410iis_driver = {
.probe = s3c2410iis_probe,
.remove = s3c2410iis_remove,
.driver = {
.name = "s3c2410-iis",
.owner = THIS_MODULE,
},
};

static int __init s3c2410_uda1341_init(void) {
memzero(&input_stream, sizeof(audio_stream_t));
memzero(&output_stream, sizeof(audio_stream_t));
return platform_driver_register(&s3c2410iis_driver);
}

static void __exit s3c2410_uda1341_exit(void) {
platform_driver_unregister(&s3c2410iis_driver);
}

module_init(s3c2410_uda1341_init);
module_exit(s3c2410_uda1341_exit);

MODULE_LICENSE("GPL");
MODULE_AUTHOR("superlp<>");
MODULE_DESCRIPTION("S3C2410 uda1341 sound driver");

文件:	s3c2410-uda1341.zip
大小:	8KB
下载:	下载