CentOS 5.5 更新网卡驱动

Linux* e1000e 基础驱动程序概述和安装

转自：

操作系统： release 5.5 (Final)

故障现象：网卡无故自动down掉，使用service network restart 重启后没多久又会自动down , 连接数大概在200个左右，没有arp攻击；

网卡信息：
[root@~]# cat /var/log/dmesg |grep eth0
eth0: Broadcom NetXtreme II BCM5709 1000Base-T (C0) PCI Express found at mem d6000000, IRQ 90, node addr 842b2bfac367

当前网卡驱动：
[root@~]# ethtool -i eth0
driver: bnx2
version: 2.0.2
firmware-version: 5.2.3 NCSI 2.0.10
bus-info: 0000:01:00.0 

下载最新网卡驱动：
 

安装更新驱动：
[root@~]# unzip linux-7.4.27.zip 
Archive: linux-7.4.27.zip
creating: Server/Linux/Driver/
inflating: Server/Linux/Driver/INSTALL.TXT 
inflating: Server/Linux/Driver/netxtreme2-7.4.27-1.src.rpm 
inflating: Server/Linux/Driver/netxtreme2-7.4.27.tar.gz 
inflating: Server/Linux/Driver/netxtreme2_sup-7.4.27-1.ISO.tar.gz 
inflating: Server/Linux/Driver/README.bnx2.TXT 
inflating: Server/Linux/Driver/README.bnx2fc.TXT 
inflating: Server/Linux/Driver/README.bnx2i.TXT 
inflating: Server/Linux/Driver/README.bnx2x.TXT 
inflating: Server/Linux/Driver/RELEASE.bnx2.TXT 
inflating: Server/Linux/Driver/RELEASE.bnx2fc.TXT 
inflating: Server/Linux/Driver/RELEASE.bnx2i.TXT 
inflating: Server/Linux/Driver/RELEASE.bnx2x.TXT 
inflating: Server/Linux/Driver/RELEASE.fclibs.TXT 

[root@~]# cd Server/Linux/Driver/
[root@ Driver]# rpm -ivh netxtreme2-7.4.27-1.src.rpm

重建对应系统的rpm包：

[root@ Driver]# cd /usr/src//SPECS/
[root@ SPECS]# rpmbuild -bb netxtreme2.spec

安装新的rmp包： 
[root@ SPECS]# cd /usr/src/redhat/RPMS/x86_64 
[root@ x86_64]# rpm -ivh netxtreme2-7.4.27-1.x86_64.rpm 


切换网卡驱动：
[root@~]# cat change_driver.sh 
rmmod bnx2 
rmmod bnx2x 
modprobe bnx2

modprobe bnx2x 

[root@~]# chmod u+x change_driver.sh 


后台执行脚本：

[root@~]# ./change_driver.sh & 

注意：有时候可能需要重启服务器使服务器系统重新完全加载新的驱动：

 

 

查看新的网卡驱动信息：

[root@ ~]# ethtool -i eth0

driver: bnx2
version: 2.2.3f
firmware-version: 6.2.12 bc 5.2.3 NCSI 2.0.11
bus-info: 0000:01:00.0

 

目前已没有出现自动down的情况。




注意：安装前请仔细看INSTALL.TXT 
如下：
[root@ Driver]# cat INSTALL.TXT 
Installation Notes
Broadcom NetXtremeII Linux Drivers
09/26/2011

Broadcom Corporation
5300 California Avenue,
Irvine, CA 92617

Copyright (c) 2004 - 2011 Broadcom Corporation
All rights reserved

Table of Contents
=================

Introduction
Limitations
Packaging
Installing Source RPM Package
Building Driver From TAR File
Unloading and Removing Driver

Introduction
============

This file describes the installation procedures for the following
Broadcom Linux drivers:

- bnx2 driver for the Broadcom NetXtreme II BCM5706/BCM5708/5709/5716
10/100/1000/2500/10000 Mbps PCIX/PCIE Ethernet Network Controller.

- bnx2x driver for the Broadcom NetXtremeII BCM57710/BCM57711/BCM57711E/BCM57712
10/100/1000/2500/10000 Mbps PCIE Ethernet Network Controller.

- cnic driver that supports additional features required by the bnx2i iSCSI
offload driver, and bnx2fc FCoE offload driver.

Limitations
===========

The current versions of the drivers have been tested on 2.4.x kernels starting
from 2.4.24 and all 2.6.x kernels. The driver may not compile on kernels
older than 2.4.24. Testing is concentrated on i386 and x86_64 architectures.
Only limited testing has been done on some other architectures.

Minor changes to some source files and Makefile may be needed on some
kernels.

Additionally, the Makefile will not compile the cnic driver on kernels
older than 2.6.16. iSCSI offload is only supported on 2.6.16 and newer
kernels. FCoE offload is only supported on 2.6.32 and newer kernels.

Packaging
=========

The driver is released in two packaging formats: source RPM and compressed tar
formats. The file name for the source RPM is:

netxtreme2-.src.rpm

The file name for the tar archive is:
netxtreme2-.tar.gz.

Identical source files to build the drivers are included in both packages.

Following is a list of files included -

a) netxtreme2-.src.rpm - NetXtreme II L2/cnic/bnx2fc/libfc/libfcoe
driver source RPM
b) netxtreme2-.tar.gz - tar zipped NetXtreme II
L2/cnic/bnx2fc/libfc/libfcoe driver source
c) INSTALL.TXT - This file
d) README..TXT - driver specific readme instructions, 
where driver is bnx2, bnx2x, bnx2i, bnx2fc.
e) RELEASE..TXT - release information text providing list of bug fixes
and enhancement for each driver.

Installing Source RPM Package
=============================

The following are general guidelines for installing the driver.

1. Install the source RPM package:

rpm -ivh netxtreme2-.src.rpm

2. CD to the RPM path and build the binary driver for your kernel:

cd /usr/src/{redhat,OpenLinux,turbo,packages,rpm ..}
(For RHEL 6.0 and above, cd ~/rpmbuild )

rpm -bb SPECS/netxtreme2.spec

or

rpmbuild -bb SPECS/netxtreme2.spec (for RPM version 4.x.x)

Note that the RPM path is different for different Linux distributions.

The driver will be compiled for the running kernel by default. To build
the driver for a kernel different than the running one, specify the
kernel by defining it in KVER:

rpmbuild -bb SPECS/netxtreme2.spec --define "KVER "

where in the form of 2.x.y-z is the version of another
kernel that is installed on the system.

3. Install the newly built package (driver and man page):

rpm -ivh RPMS//netxtreme2-..rpm

where is the machine architecture such as i386:

rpm -ivh RPMS/i386/netxtreme2-.i386.rpm

Note that the --force option may be needed on some Linux distributions
if conflicts are reported.

The drivers will be installed in the following path:

2.4.x kernels:

/lib/modules//kernel/drivers/net/bnx2.o
/lib/modules//kernel/drivers/net/bnx2x.o

2.6.0 kernels:

/lib/modules//kernel/drivers/net/bnx2.ko
/lib/modules//kernel/drivers/net/bnx2x.ko

2.6.16 and newer kernels:

/lib/modules//kernel/drivers/net/bnx2.ko
/lib/modules//kernel/drivers/net/bnx2x.ko
/lib/modules//kernel/drivers/net/cnic.ko

Newer RHEL and SLES distros:

/lib/modules//updates/bnx2.ko
/lib/modules//updates/cnic.ko
/lib/modules//updates/bnx2x.ko
/lib/modules//updates/bnx2i.ko
/lib/modules//updates/bnx2fc.ko

4. Unload existing driver if necessary:

rmmod bnx2
rmmod bnx2x

If the cnic driver is loaded, it should also be unloaded along with dependent
drivers:

rmmod bnx2fc
rmmod bnx2i
rmmod cnic

5. Load the bnx2 driver for the BCM5706/BCM5708/5709/5716 devices:

insmod bnx2.o
or
insmod bnx2.ko (on 2.6.x kernels)
or
modprobe bnx2

To load the bnx2x driver for the BCM57710/BCM57711/BCM57711E/BCM57712 devices:

insmod bnx2x.o
or
insmod bnx2x.ko (on 2.6.x kernels)
or
modprobe bnx2x

To load the cnic driver:

insmod cnic.ko
or
modprobe cnic

To load the bnx2i driver:

insmod bnx2i.ko
or
modprobe bnx2i
service iscsid restart (Please refer REDAME.bnx2i.txt for more details 
about iSCSI operation)

To load the bnx2fc driver for BCM57712 device:

insmod bnx2fc.ko
or
modprobe bnx2fc
service fcoe start (Please refer README.bnx2fc.txt for more details about 
FCoE operation)

Note that the inbox kernel may have an older version of bnx2, bnx2x and cnic
driver. It is important for FCoE offload user to unload these inbox versions
before attempting to load bnx2fc driver. There are 2 options to reach the
desired goal,
a) Reboot the server
OR
b) If already loaded, unload inbox bnx2, bnx2x, cnic drivers and load newly
installed version from netxtreme2-foce package using 'modprobe '

NOTE: Driver upgrade (rpm -Uvh) is not supported.
NOTE: On SLES 11, change "allow_unsupported_modules" parameter value of
/etc/modprobe.d/unsupport-modules' from 0 to 1, until bnx2fc driver
is inbox. Failing to do so will not load bnx2fc.

6. To configure network protocol and address, refer to various Linux
documentations.

Building Driver From TAR File
=============================

The following are general guidelines for installing the driver.

1. Create a directory and extract the files:

tar xvzf netxtreme2-.tar.gz

2. Build the drivers as a loadable module for the running kernel:

make

The driver will be compiled for the running kernel by default. To build
the driver for a kernel different than the running one, specify the
kernel by defining it in KVER:

make KVER=

where in the form of 2.x.y-z is the version of another
kernel that is installed on the system.

3. Test the driver by loading it (Same procedures as described in the 
Source RPM section above).

4. Install the driver and man page:

make install

See RPM instructions above for the location of the installed driver.

5. To configure network protocol and address, refer to various Linux
documentations.

Unloading and Removing Driver
=============================

If the driver was installed using rpm, do the following to remove it:

rpm -e nextreme2

Note - this will remove libfc2, libfcoe2, bnx2, bnx2x and cnic modules as well

If the driver was installed using make install from the tar file, the drivers
have to be manually deleted from the system. Refer to the section
"Installing Source RPM Package" for the location of the installed driver.

1. rmmod

2. delete .ko from location given in section "Installing Source RPM Package"

3. depmod -a

**The kernel will now be back to original state prior to instalation from tar file.
You may now reload previous module versions if necessary.

推荐阅读：

DELL PowerEdge R720 安装ESXi 5.0 U1网卡驱动问题 

RHEL6.4 安装Broadcom BCM4313无线网卡驱动 

CentOS 6.4 64位下安装BCM4313无线网卡驱动 

更多CentOS相关信息见 专题页面 

转自：http://www.cnblogs.com/JemBai/archive/2012/03/22/2412496.html

DELL的R310或是R410服务器安装centos会遇到网卡驱动问题。现象为，在网上负载较高后网上自动down掉。所以需要更新网卡驱动。

1、先确认当前驱动版本：
 bnx2  #或直接ethtool -i eth0 可以查看到固件版本

2、驱动下载

当前版本为：linux-7.0.36.

3、安装包选择
 linux-7.0.36.zip #驱动程序其中已包括源代码及rpm包
 Server/Linux/Driver
rpm -ivh netxtreme2-7.0.36-1.src.rpm #解压出包源码
   1:netxtreme2             ########################################### [100%]
cd /usr/src/redhat/SPECS/
rpmbuild -bb netxtreme2.spec #重建生产对应系统的rpm包
cd ../RPMS/i386/
rpm -ivh netxtreme2-7.0.36-1.i386.rpm #安装网卡驱动

4、网卡驱动切换：
vim change_driver.sh
mod bnx2
 bnx2
 755 change_driver.sh
./change_driver.sh  #后台执行脚本
注：正常情况网络会出现中断一会重新加载完成会自动恢复，如果出现异常未能自动恢复可能需要重启服务器使系统完成重新加载新网卡驱动

5、核实更新后当前驱动版本：
modinfo bnx2 #或直接ethtool -i eth0 可以查看到固件版本

可能遇到的问题:环境需求:

yum -y install gcc mack kernel-headers kernel-devel