Chinaunix首页 | 论坛 | 博客
  • 博客访问: 133788
  • 博文数量: 51
  • 博客积分: 3010
  • 博客等级: 中校
  • 技术积分: 400
  • 用 户 组: 普通用户
  • 注册时间: 2007-05-22 14:47
文章分类

全部博文(51)

文章存档

2009年(8)

2008年(43)

我的朋友

分类: 系统运维

2008-09-02 03:31:16

现在手里有一个无线路由器(TP-LINK), 家里有2台电脑,都有无线网卡. 以下是2台电脑通过无线路由器上网的配置过程.

电脑,modem, TP-LINK无线路由器,都上电.

电脑和modem用网线连接好. 从电脑这边能用ping 192.168.1.1 的命令 ping 通modem默认的IP,通常是192.168.1.1.

打开一个IE 窗口,输入 ,进入配置窗口,准备对modem进行配置.

配置目的: 把 modem从 PPPoE 改为 Bridge 模式.
步骤:
Step 1: logging into the modem and go to the advanced tab.

Step 2: Choosing “quickstart”

Step 3:Choosing bridge mode

Step 4: in Bridge mode menu change the "quickstart" to "bridge"

Step 5:Go to Lan Configuration Menu

Step 6: highlight the name “bridge” in the interfaces menu and click add on the right hand side under the “LAN group 1” menu, then click apply.

Step 7: After that is complete go back to the “LAN group 1” menu and highlight “bridge” once again and click configure.

Step 8: Once that page is loaded goto the bottom of the page and choose the opition “Server and Relay off” and click apply.

Step 9:After these steps are complete make sure to save your settings by going to the top left hand side and clicking save settings.
这里基本对modem的配置上就OK了. 以上步骤可以到 网址去查看,我写得太乱,呵呵...

然后是对无线路由器的配置.

用网线把电脑和无线路由器连接起来. 通常是接到路由器的lan 口. 一般路由器都有4个port,随便一个都行.

从电脑这边能用ping 的命令 ping 通路由器默认的IP,通常是192.168.1.1.

打开一个IE 窗口,输入 ,进入配置窗口,准备对路由器进行配置.

在无线路由里面, 通常有三种方式给你选择, 你只要选PPPoE 即可.
然后输入上网的账号和密码,并配置启用无线功能.
这里账号和密码是internet 服务提供商给你的,你可以在附送的安装手册和modem里面找到它们.
保存对路由器的配置,退出.

重新连线. 用网线把modem和路由器连接起来. 路由器这边接口是WAN port. modem这边接口是ETHERNET port.

在电脑里查找你的wireless network, 找到后点击进行connect, 连上后,呵呵...

现在就可以开始多台电脑无线上网了.

注意的地方:
1.注意在无线路由器里面,有一个连接的设置,最好选“断线后自动连接”;否则,如果断线了而无线路由器不自动重新连接,就比较麻烦。
2.请认真检查输入的账号和密码,万一不小心输错了,而你又不知道,那么查起问题来就没有方向了,呵呵... 经验啊!
阅读(1115) | 评论(0) | 转发(0) |
给主人留下些什么吧!~~