分类： LINUX
2007-11-21 23:57:54
|
MikroTik RouteOS 2.9.27无线设置手册 |
|
一、MikroTik RouteOS 2.9.27无线支持模式 1、station模式：客户端 2、bridge模式：无线桥（作用跟ap-bridge类似，但仅支持一个客户端） 3、ap-bridge模式：无线接入点 4、alignment-only模式：天线定位模式（测试用） 5、nstreme模式：MikroTik专有无线模式，用于远距离传输 6、station-wds模式：工作在客户端模式，但能与无线分布系统（WDS）通信 7、wds-slave模式：工作在无线接入点（ap-bridge）模式，但如果WDS的频率改变能自动适应 二、配置WDS 1、配置AP及主WDS [admin@WDS_AP] > interface bridge [admin@WDS_AP] interface bridge> add [admin@WDS_AP] interface bridge> print Flags: X - disabled, R - running 0 R name="bridge1" mtu=1500 arp=enabled mac-address=B0:62:0D:08:FF:FF stp=no priority=32768 ageing-time=5m forward-delay=15s garbage-collection-interval=4s hello-time=2s max-message-age=20s [admin@WDS_AP] interface bridge> port [admin@WDS_AP] interface bridge port> print # INTERFACE BRIDGE PRIORITY PATH-COST 0 Public none 128 10 1 wlan1 none 128 10 [admin@WDS_AP] interface bridge port> set 0 bridge=bridge1 [admin@WDS_AP] interface bridge port> /in wireless [admin@WDS_AP] interface wireless> set wlan1 mode=ap-bridge ssid=wds-sta-test \ wds-mode=dynamic wds-default-bridge=bridge1 disabled=no band=2.4ghz-b/g \ frequency=2437 [admin@WDS_AP] interface wireless> print Flags: X - disabled, R - running 0 name="wlan1" mtu=1500 mac-address=00:0C:42:05:00:22 arp=enabled disable-running-check=no interface-type=Atheros AR5413 radio-name="000C42050022" mode=ap-bridge ssid="wds-sta-test" area="" frequency-mode=superchannel country=no_country_set antenna-gain=0 frequency=2437 band=2.4ghz-b/g scan-list=default rate-set=default supported-rates-b=1Mbps,2Mbps,5.5Mbps,11Mbps supported-rates-a/g=6Mbps,9Mbps,12Mbps,18Mbps,24Mbps,36Mbps,48Mbps, 54Mbps basic-rates-b=1Mbps basic-rates-a/g=6Mbps max-station-count=2007 ack-timeout=dynamic tx-power=default tx-power-mode=default noise-floor-threshold=default periodic-calibration=default burst-time=disabled fast-frames=no dfs-mode=none antenna-mode=ant-a wds-mode=dynamic wds-default-bridge=bridge1 wds-ignore-ssid=no update-stats-interval=disabled default-authentication=yes default-forwarding=yes default-ap-tx-limit=0 default-client-tx-limit=0 hide-ssid=no security-profile=default disconnect-timeout=3s on-fail-retry-time=100ms preamble-mode=both [admin@WDS_AP] interface wireless> 2、配置基站及辅WDS [admin@WDS_Station] > interface bridge [admin@WDS_Station] interface bridge> add [admin@WDS_Station] interface bridge> print Flags: X - disabled, R - running 0 R name="bridge1" mtu=1500 arp=enabled mac-address=11:05:00:00:02:00 stp=no priority=32768 ageing-time=5m forward-delay=15s garbage-collection-interval=4s hello-time=2s max-message-age=20s [admin@WDS_Station] interface bridge> port [admin@WDS_Station] interface bridge port> print # INTERFACE BRIDGE PRIORITY PATH-COST 0 Local none 128 10 1 wlan1 none 128 10 [admin@WDS_Station] interface bridge port> set 0,1 bridge=bridge1 [admin@WDS_Station] interface bridge port> /interface wireless [admin@WDS_Station] interface wireless> set wlan1 mode=station-wds disabled=no \ \... ssid=wds-sta-test band=2.4ghz-b/g [admin@WDS_Station] interface wireless> print Flags: X - disabled, R - running 0 R name="wlan1" mtu=1500 mac-address=00:0B:6B:34:5A:91 arp=enabled disable-running-check=no interface-type=Atheros AR5213 radio-name="000B6B345A91" mode=station-wds ssid="wds-sta-test" area="" frequency-mode=superchannel country=no_country_set antenna-gain=0 frequency=2412 band=2.4ghz-b/g scan-list=default rate-set=default supported-rates-b=1Mbps,2Mbps,5.5Mbps,11Mbps supported-rates-a/g=6Mbps,9Mbps,12Mbps,18Mbps,24Mbps,36Mbps,48Mbps, 54Mbps basic-rates-b=1Mbps basic-rates-a/g=6Mbps max-station-count=2007 ack-timeout=dynamic tx-power=default tx-power-mode=default noise-floor-threshold=default periodic-calibration=default burst-time=disabled fast-frames=no dfs-mode=none antenna-mode=ant-a wds-mode=disabled wds-default-bridge=none wds-ignore-ssid=no update-stats-interval=disabled default-authentication=yes default-forwarding=yes default-ap-tx-limit=0 default-client-tx-limit=0 hide-ssid=no security-profile=default disconnect-timeout=3s on-fail-retry-time=100ms preamble-mode=both [admin@WDS_Station] interface wireless> 注意：一定要记得做个bridge把wlan1和ether1连起来。 玩到这里，感觉MikroTik Route OS功能超强啊。 不知哪能找好远的天线？:D Update:配置无线AP时，需要先给wlan1接口配置IP地址，再在该接口上配置DHCP才能生效 |
