前提条件：
make_tape_recovery -A操作成功。
操作步骤：
1，重启系统，自检通过后在十秒中断处中断，如下所示：
Firmware Version 43.43
Duplex Console IO Dependent Code (IODC) revision 1
------------------------------------------------------------------------------
(c) Copyright 1995-2002, Hewlett-Packard Company, All rights reserved
------------------------------------------------------------------------------
Processor Speed State CoProcessor State Cache Size
Number State Inst Data
--------- -------- --------------------- ----------------- ------------
1 440 MHz Active Functional 512 KB 1 MB
3 440 MHz Idle Functional 512 KB 1 MB
5 440 MHz Idle Functional 512 KB 1 MB
7 440 MHz Idle Functional 512 KB 1 MB
Central Bus Speed (in MHz) : 120
Available Memory : 4193284 KB
Good Memory Required : 18880 KB
Primary boot path: 0/0/2/1.6
Alternate boot path: 0/0/2/0.6
Console path: 0/0/4/0.0
Keyboard path: 0/0/4/0.0
WARNING: The non-destructive test bit was set, so memory was not tested
destructively. Information only, no action required.
Processor is starting autoboot process.
To discontinue, press any key within 10 seconds.
Boot terminated.
2，通过“sea IPL”命令搜索可引导设备，找到磁带机的硬件路径地址0/0/1/0.0
3，通过磁带机引导，过程如下：
Main Menu: Enter command or menu > bo 0/0/1/0.0
Interact with IPL (Y, N, or Cancel)?> n
Booting...
Boot IO Dependent Code (IODC) revision 1
HARD Booted.
ISL Revision A.00.44 Mar 12, 2003
ISL booting hpux (;0):INSTALL
Boot
: tape(0/0/1/0.0.0.0.0.0.0;0):WINSTALL
11751424 + 1970264 + 2631464 start 0x200d68
alloc_pdc_pages: Relocating PDC from 0xffff800000 to 0x7eb00000.
4，加载内核成功后，有如下显示：
gate64: sysvec_vaddr = 0xc0002000 for 2 pages
NOTICE: nfs3_link(): File system was registered at index 4.
NOTICE: autofs_link(): File system was registered at index 6.
NOTICE: cachefs_link(): File system was registered at index 7.
td: claimed Tachyon TL/TS Fibre Channel Mass Storage card at 1/2/0/0
System Console is on the Built-In Serial Interface
Swap device table: (start & size given in 512-byte blocks)
entry 0 - auto-configured on root device; ignored - no room
WARNING: no swap device configured, so dump cannot be defaulted to primary swap.
WARNING: No dump devices are configured. Dump is disabled.
Starting the STREAMS daemons-phase 1
Create STCP device files
Starting the STREAMS daemons-phase 2
$Revision: vmunix: vw: -proj selectors: CUPI80_BL2000_1108 -c 'Vw for CUPI80_BL2000_1108 build' -- cupi80_bl2000_1108 'CUPI80_BL2000_1108' Wed Nov 8 19:24:56 PST 2000 $
Memory Information:
physical page size = 4096 bytes, logical page size = 4096 bytes
Physical: 4194304 Kbytes, lockable: 3203460 Kbytes, available: 3693540 Kbytes
======= 06/21/07 02:21:21 EDT HP-UX Installation Initialization. (Thu Jun 21
02:21:21 EDT 2007)
@(#) Ignite-UX Revision C.6.1.44
@(#) install/init (opt) $Revision: 10.303 $
* Scanning system for IO devices...
* Querying disk device: 0/0/2/1.6.0 ...
Recovery tape created from system: 4000new on Thu Jun 21 12:51:03 2007
WARNING: The configuration information calls for a non-interactive
installation.
Press within 10 seconds to cancel batch-mode installation:
* Using client directory: /var/opt/ignite/clients/0x00306E1345B1
* Checking configuration for consistency...
NOTE: Free space (4129584KB) in "/var" where /var/adm/crash is located is
less than system memory (4194304KB). This should be enough space to
capture at least a single dump (and likely more than that if the dump
is selective and/or compressed) in the event of a system crash.
Additional space may be required to uncompress the dump in order to
analyze it and to save multiple dumps. You can increase the size of
the "/var" volume on the "File System" tab when using the advanced
user interface.
WARNING: The disk at: 0/0/2/1.6.0 (HP_36.4GST336752LC) appears to contain a
file system and boot area. Continuing the installation will destroy
any existing data on this disk.
Press within 10 seconds to cancel batch-mode installation:
Really cancel non-interactive install and start the
user-interface? ([y]/n): y
* Setting keyboard language to: PS2_DIN_US_English.
NOTE:
The console firmware terminal type is currently set to "vt100". If you
are using any other type of terminal you will see "garbage" on the
screen following this message.
If this is the case, you will need to either change the terminal type
set in the firmware via GSP (if your GSP firmware version supports
this feature), or change your terminal emulation to match the
firmware. In either case you will need to restart if your terminal and
the firmware terminal type do not match.
Press the 'b' key if you want to reboot now.
Recovery tape created from system: 4000new on Thu Jun 21 12:51:03 2007
5，通过手工中断，来到和光盘引导相同的安装界面：
Welcome to the HP-UX installation/recovery process!
Use the key to navigate between fields, and the arrow keys
within fields. Use the key to select an item.
Use the or to pop-up a choices list. If the
menus are not clear, select the "Help" item for more information.
Hardware Summary: System Model: 9000/800/N4000-44
+---------------------+----------------+-------------------+ [ Scan Again ]
| Disks: 1 ( 33.9GB) | Floppies: 0 | LAN cards: 5 |
| CD/DVDs: 0 | Tapes: 1 | Memory: 4096Mb |
| Graphics Ports: 0 | IO Buses: 4 | CPUs: 4 | [ H/W Details ]
+---------------------+----------------+-------------------+
[ Install HP-UX ]
[ Run a Recovery Shell ]
[ Advanced Options ]
[ Read Sys-Admin Message ]
[ Reboot ] [ Help ]
6，按需求进行安装即可。
阅读(3593) | 评论(2) | 转发(0) |
