Chinaunix首页 | 论坛 | 博客
  • 博客访问: 522342
  • 博文数量: 184
  • 博客积分: 0
  • 博客等级: 民兵
  • 技术积分: 1172
  • 用 户 组: 普通用户
  • 注册时间: 2016-06-21 13:40
个人简介

技术改变命运

文章分类

全部博文(184)

文章存档

2020年(16)

2017年(12)

2016年(156)

我的朋友

分类: LINUX

2017-01-10 14:48:02

 

安装环境:
       操作系统:redhat 12.0
       OpenSSL Version:openssl-0.9.8l

Download

  • 安装包(Linux source) : openssl-0.9.8l.tar.gzor the latest version of openssl
      下载地址:
  • 在linux下解压缩下载到的安装包,命令如下.....
    tar -xzf openssl-xxx.tar.gz

Our Configuration

  • Install to : /usr/local/ssl
  • Module type : dynamically and staticly loaded modules, *.so *.a

Build Instructions

Configure

.../openssl-0.9.8l]# ./config --prefix=/usr/local/ssl-0.9.8l shared zlib-dynamic enable-camellia

  • --prefix=/usr/local/ssl-0.9.8l
    [this is the installation location; default is '/usr/local/ssl' -- which we will symlink]
  • shared
    [in addition to the usual static libraries, create shared libraries]
  • zlib-dynamic
    [like "zlib", but has OpenSSL load the zlib library dynamically when needed]
  • enable-camellia
    [enables the symmetric cipher 'Camellia' (128-bit, 192-bit, 256-bit key versions), which is now available for royalty-free use]

display guess on system made by './config'...

.../openssl-0.9.8l]# ./config -t

Build and Install

  • .../openssl-0.9.8l]# make depend
    [step required since extra cipher was enabled]
  • .../openssl-0.9.8l]# make
  • .../openssl-0.9.8l]# make test
  • .../openssl-0.9.8l]# make install

Symlink

Form symlink from '/usr/local/ssl-0.9.8l' to '/usr/local/ssl'...]代表“/usr/local/

  • ...]# cd /usr/local
  • /usr/local]# ln -s ssl-0.9.8l ssl

Update the Run-time Linker

ld.so.cache will need to be updated with the location of the new OpenSSL shared libs: libcrypto.so.0.9.8 and libssl.so.0.9.8

Sometimes it is sufficient to just symlink or copy these two files to /lib, but we recommend you follow these instructions instead.

Edit /etc/ld.so.conf, add to paths...(修改效果如下图1,当然也可以直接在/etc/ld.so.conf.d文件夹下再创建一个.conf文件,把/usr/local/ssl/lib拷贝到里面,另外也可以在现有的.conf文件中添加这个路径,反正ld.so.conf中包含了这个文件夹下的所有.conf文件)

1

/usr/local/ssl/lib

Update the run-time linker...

...]# ldconfig

Update the PATH

Edit /root/.bash_profile, add to PATH variable...

(若原来没有安装openssl的旧版本,则放在PATH中的任何位置都可以,但是记住要用冒号分隔开,而不是分号分隔,详见后面的截图,若想查看当前的PATH环境变量都设置了什么,可以使用如下的命令实现:

[root@localhost local]# echo $PATH

/usr/local/ssl/bin:/usr/lib/qt-3.3/bin:/usr/kerberos/sbin:/usr/kerberos/bin:/usr/local/sbin:/usr/local/bin:/sbin:/bin:/usr/sbin:/usr/bin:/usr/X11R6/bin:/root/bin

NOTE:一般在root下直接是看不见.bash_profile(一般为隐藏文件)的,可以在该目录下使用ls –a 命令来显示隐藏了的文件。然后用VIemacs编辑器来修改其中的内容。编译完成后若要立刻看到效果,可以用命令:source .bash_profile ,若要长期起作用,需要重新登录(当我首次安装的时候是出现的情况是这样的~~~

/usr/local/ssl/bin

Re-login.

[sanity check] OpenSSL

Verify that binary 'openssl' is linking against the correct ssl libraries...

  • [root@localhost /]# cd /usr/local
  • [root@localhost local]# ldd /usr/local/ssl/bin/openssl
  •         linux-gate.so.1 =>  (0x00c4b000)
  •         libssl.so.0.9.8 => /usr/local/ssl-0.9.8l/lib/libssl.so.0.9.8 (0x00d5b000)
  •         libcrypto.so.0.9.8 => /usr/local/ssl-0.9.8l/lib/libcrypto.so.0.9.8 (0x00110000)
  •         libdl.so.2 => /lib/libdl.so.2 (0x005b2000)
  •         libc.so.6 => /lib/libc.so.6 (0x00447000)
  •         /lib/ld-linux.so.2 (0x0042a000)

...]# which openssl

/usr/local/ssl/bin/openssl

...]# openssl version

OpenSSL 0.9.8l 5 Nov 2009

If another path, or an older version is shown, your system contains a previously installed OpenSSL that is first [relative to the newer openssl] in the path.

Repeate the steps in section 'Update the PATH', except place the specified location at the start of the PATH variable.(/root/.bash_profile中将PATH设置为如下的顺序,即把当前安装上的openssl的版本放在环境变量的前面,这样优先使用的就是新安装的最新的版本的OpenSSL了)

2

Note that the older openssl, on most systems, is located under /usr/bin

The location of 'openssl' can be found with...(用下面的命令你就可以查到你的openssl的安装目录了~~~

...]# which openssl

以上只是我在刚开始学习的时候的安装过程,若有不对的地方或还有更好的方法,欢迎大家批评指正~~~


阅读(3121) | 评论(0) | 转发(0) |
给主人留下些什么吧!~~