Debian 4 GDM Root问题

Submitted by xmasfox on Wed, 2007-05-30 21:56.

in

在下从FC来不久，用Debian 太菜
是这样：
我想在GDM 时有Root登陆，就进了 /etc/gdm/ 改 gdm.conf 把AllowRoot＝true 加上
可没反映，（在GDM登陆界面下 ctrl＋alt＋F2，用VI改，，ALT＋F2退出）如下

# GDM Configuration Customization file.
#
# This file is the appropriate place for specifying your customizations to the
# GDM configuration. If you run gdmsetup, it will automatically edit this
# file for you and will cause the daemon and any running GDM GUI programs to
# automatically update with the new configuration. Not all configuration
# options are supported by gdmsetup, so to modify some values it may be
# necessary to modify this file directly by hand.
#
# Older versions of GDM used the "gdm.conf" file for configuration. If your
# system has an old gdm.conf file on the system, it will be used instead of
# this file - so changes made to this file will not take effect. Consider
# migrating your configuration to this file and removing the gdm.conf file.
#
# To hand-edit this file, simply add or modify the key=value combination in
# the appropriate section in the template below. Refer to the comments in the
# /usr/share/gdm/defaults.conf file for information about each option. Also
# refer to the reference documentation.
#
# If you hand edit a GDM configuration file, you should run the following
# command to get the GDM daemon to notice the change. Any running GDM GUI
# programs will also be notified to update with the new configuration.
#
# gdmflexiserver --command="UPDATE_CONFIG "
#
# e.g, the "Enable" key in the "[debug]" section would be "debug/Enable".
#
# You can also run gdm-restart or gdm-safe-restart to cause GDM to restart and
# re-read the new configuration settings. You can also restart GDM by sending
# a HUP or USR1 signal to the daemon. HUP behaves like gdm-restart and causes
# any user session started by GDM to exit immediately while USR1 behaves like
# gdm-safe-restart and will wait until all users log out before restarting GDM.
#
# For full reference documentation see the gnome help browser under
# GNOME|System category. You can also find the docs in HTML form on
#
#
# NOTE: Lines that begin with "#" are considered comments.
#
# Have fun!

[daemon]

[security]
AllowRoot=true －－－－加了这行
[xdmcp]

[gui]

[greeter]

[chooser]

[debug]

# Note that to disable servers defined in the defaults.conf file (such as
# 0=Standard, you must put a line in this file that says 0=inactive, as
# described in the Configuration section of the GDM documentation.
#
[servers]

# Also note, that if you redefine a [server-foo] section, then GDM will
# use the definition in this file, not the defaults.conf file. It is
# currently not possible to disable a [server-foo] section defined
# in the defaults.conf file.

—————————————————————————————————————————

然后 又进 /usr/share/gdm/ 改 defaults。conf 还没反映

何解 如下

# This determines whether GDM will send notifications to the console.
#ConsoleNotify=true

# How long gdm should wait before it assumes a started Xserver is defunct and
# kills it. 10 seconds should be long enough for X, but Xgl may need 20 or 25.
GdmXserverTimeout=10

[security]
# Allow root to login. It makes sense to turn this off for kiosk use, when
# you want to minimize the possibility of break in.
AllowRoot=true ——————————修改这行
# Allow login as root via XDMCP. This value will be overridden and set to
# false if the /etc/default/login file exists and contains
# "CONSOLE=/dev/login", and set to true if the /etc/default/login file exists
# and contains any other value or no value for CONSOLE.
AllowRemoteRoot=false
# This will allow remote timed login.
AllowRemoteAutoLogin=false

sudo gdmsetup
把允许系统管理员登录选上