The USBD_STATUS data type defines USB status values for USB requests.
typedef LONG USBD_STATUS;
The most significant 4 bits of USB status values are defined in the following table.
| Value | Meaning |
|---|---|
|
00 (USBD_STATUS_SUCCESS) |
Request was completed with success. |
|
01 (USBD_STATUS_PENDING) |
Request is pending. |
|
10 or 11 (USBD_STATUS_ERROR) |
Request was completed with an error. |
The least significant 28 bits of USB status values are defined in the following table.
| Value | Code | Meaning |
|---|---|---|
|
USBD_STATUS_CRC |
0xC0000001 |
CRC error (defined for backward compatibility with the USB 1.0). |
|
USBD_STATUS_BTSTUFF |
0xC0000002 |
BTS error (defined for backward compatibility with the USB 1.0). |
|
USBD_STATUS_DATA_TOGGLE_MISMATCH |
0xC0000003 |
Data toggle mismatch. |
|
USBD_STATUS_STALL_PID |
0xC0000004 |
The device returned a stall packet identifier (defined for backward compatibility with the USB 1.0) |
|
USBD_STATUS_DEV_NOT_RESPONDING |
0xC0000005 |
The device is not responding (defined for backward compatibility with the USB 1.0). |
|
USBD_STATUS_PID_CHECK_FAILURE |
0xC0000006 |
The device returned a packet identifier check failure (defined for backward compatibility with the USB 1.0). |
|
USBD_STATUS_UNEXPECTED_PID |
0xC0000007 |
The device returned an unexpected packet identifier error (defined for backward compatibility with the USB 1.0). |
|
USBD_STATUS_DATA_OVERRUN |
0xC0000008 |
The device returned a data overrun error (defined for backward compatibility with the USB 1.0). |
|
USBD_STATUS_DATA_UNDERRUN |
0xC0000009 |
The device returned a data underrun error (defined for backward compatibility with the USB 1.0). |
|
USBD_STATUS_RESERVED1 |
0xC000000A |
Reserved. |
|
USBD_STATUS_RESERVED2 |
0xC000000B |
Reserved. |
|
USBD_STATUS_BUFFER_OVERRUN |
0xC000000C |
The device returned a buffer overrun error (defined for backward compatibility with the USB 1.0). |
|
USBD_STATUS_BUFFER_UNDERRUN |
0xC000000D |
The device returned a buffer underrun error (defined for backward compatibility with the USB 1.0). |
|
USBD_STATUS_NOT_ACCESSED |
0xC000000F |
The USB stack could not access the device (defined for backward compatibility with the USB 1.0). |
|
USBD_STATUS_FIFO |
0xC0000010 |
The device returned a FIFO error (defined for backward compatibility with the USB 1.0). |
|
USBD_STATUS_XACT_ERROR |
0xC0000011 |
The device returned a transaction error (defined for backward compatibility with the USB 1.0). |
|
USBD_STATUS_BABBLE_DETECTED |
0xC0000012 |
The device returned a babble detected error (defined for backward compatibility with the USB 1.0). |
|
USBD_STATUS_DATA_BUFFER_ERROR |
0xC0000013 |
Hardware status codes that range from 0x00000001 to 0x000000FF (defined for backward compatibility with the USB 1.0 stack). |
|
USBD_STATUS_NO_PING_RESPONSE |
0xC0000014 | No response was received from the device for a ping packet sent by the host. |
|
USBD_STATUS_INVALID_STREAM_TYPE |
0xC0000015 | The stream type is invalid for the endpoint. |
|
USBD_STATUS_INVALID_STREAM_ID |
0xC0000016 | The stream identifier is invalid. |
|
USBD_STATUS_ENDPOINT_HALTED |
0xC0000030 |
A transfer was submitted to an endpoint that is stalled. |
|
USBD_STATUS_INVALID_URB_FUNCTION |
0x80000200 |
Invalid URB function. |
|
USBD_STATUS_INVALID_PARAMETER |
0x80000300 |
Invalid parameter. |
|
USBD_STATUS_ERROR_BUSY |
0x80000400 |
The client driver caused an error by attempting to close an endpoint, interface, or configuration handle with outstanding transfers. |
|
USBD_STATUS_REQUEST_FAILED |
0x80000500 |
The hub driver cannot complete a URB request. |
|
USBD_STATUS_INVALID_PIPE_HANDLE |
0x80000600 |
Invalid pipe handle. |
|
USBD_STATUS_NO_BANDWIDTH |
0x80000700 |
There was not enough bandwidth to open a requested endpoint. |
|
USBD_STATUS_INTERNAL_HC_ERROR |
0x80000900 |
Unspecified host controller error. |
|
USBD_STATUS_ERROR_SHORT_TRANSFER |
0x80000900 |
The transfer ended with a short packet, but the USBD_SHORT_TRANSFER_OK bit is not set for the pipe. |
|
USBD_STATUS_BAD_START_FRAME |
0xC0000A00 |
The requested start frame is not within a range of USBD_ISO_START_FRAME_RANGE frames of the current USB frame. Whenever this error occurs, the system sets the stall bit on the pipe. |
|
USBD_STATUS_ISOCH_REQUEST_FAILED |
0xC0000B00 |
The host controller returns this error whenever all packets in an isochronous transfer complete with an error. |
|
USBD_STATUS_FRAME_CONTROL_OWNED |
0xC0000C00 |
The hub driver returns this error whenever the frame length control for the host controller is being used by a driver other than the host controller driver. |
|
USBD_STATUS_FRAME_CONTROL_NOT_OWNED |
0xC0000D00 |
The hub driver returns this error if the caller does not own frame length control and attempts to release or modify the host controller frame length. |
|
USBD_STATUS_NOT_SUPPORTED |
0xC0000E00 |
The request was not supported. |
|
USBD_STATUS_INAVLID_CONFIGURATION_DESCRIPTOR |
0xC0000F00 |
Invalid configuration descriptor. |
|
USBD_STATUS_INSUFFICIENT_RESOURCES |
0xC0001000 |
Insufficient resources. |
|
USBD_STATUS_SET_CONFIG_FAILED |
0xC0002000 |
An attempt to change the device configuration failed. |
|
USBD_STATUS_BUFFER_TOO_SMALL |
0xC0003000 |
The buffer is too small. |
|
USBD_STATUS_INTERFACE_NOT_FOUND |
0xC0004000 |
The interface was not found. |
|
USBD_STATUS_INAVLID_PIPE_FLAGS |
0xC0005000 |
Invalid pipe flags. |
|
USBD_STATUS_TIMEOUT |
0xC0006000 |
The request timed out. |
|
USBD_STATUS_DEVICE_GONE |
0xC0007000 |
The device is no longer present in the system. |
|
USBD_STATUS_STATUS_NOT_MAPPED |
0xC0008000 |
The device bus address is not mapped to system memory. |
|
USBD_STATUS_HUB_INTERNAL_ERROR |
0xC0009000 |
The hub driver returns this error whenever it intercepted a URB that was targeted at some other device. |
|
USBD_STATUS_CANCELED |
0xC0010000 |
The USB stack reports this error whenever it completed a transfer because of an AbortPipe request from the client driver. |
|
USBD_STATUS_ISO_NOT_ACCESSED_BY_HW |
0xC0020000 |
The host controller did not access the transfer descriptor (TD) that is associated with this packet. The USB stack reports this error in the packet status field of an isochronous transfer packet. |
|
USBD_STATUS_ISO_TD_ERROR |
0xC0030000 |
The host controller reported an error in the transfer descriptor (TD). The USB stack reports this error in the packet status field of an isochronous transfer packet. |
|
USBD_STATUS_ISO_NA_LATE_USBPORT |
0xC0040000 |
The client driver submitted the packet on time, but the packet failed to reach the miniport driver on time. The USB stack reports this error in the packet status field of an isochronous transfer packet. |
|
USBD_STATUS_ISO_NOT_ACCESSED_LATE |
0xC0050000 |
The client driver did not submit the packet on time. The USB stack reports this error in the packet status field of an isochronous transfer packet. |
|
USBD_STATUS_BAD_DESCRIPTOR |
0xC0100000 |
Invalid descriptor. |
|
USBD_STATUS_BAD_DESCRIPTOR_BLEN |
0xC0100001 |
Invalid descriptor length. |
|
USBD_STATUS_BAD_DESCRIPTOR_TYPE |
0xC0100002 |
Invalid descriptor type. |
|
USBD_STATUS_BAD_INTERFACE_DESCRIPTOR |
0xC0100003 |
Invalid interface descriptor. |
|
USBD_STATUS_BAD_ENDPOINT_DESCRIPTOR |
0xC0100004 |
Invalid endpoint descriptor. |
|
USBD_STATUS_BAD_INTERFACE_ASSOC_DESCRIPTOR |
0xC0100005 |
Invalid interface association descriptor. |
|
USBD_STATUS_BAD_CONFIG_DESC_LENGTH |
0xC0100006 |
Invalid configuration descriptor length. |
|
USBD_STATUS_BAD_NUMBER_OF_INTERFACES |
0xC0100007 |
Invalid number of interfaces. |
|
USBD_STATUS_BAD_NUMBER_OF_ENDPOINTS |
0xC0100008 |
Invalid number of endpoints. |
|
USBD_STATUS_BAD_ENDPOINT_ADDRESS |
0xC0100009 |
Invalid endpoint address. |