全部博文（200）
分类：
2013-01-07 15:10:08
原文地址：Zigbee网络设备启动流程—协调器(自启动模式) 作者：xn_liu
使用的协议栈版本信息: ZigBee2006\ZStack-1.4.3-1.2.1
Zigbee网络设备启动流程—协调器(自启动模式)—以SampleApp的协调器为例.
1、协调器预编译信息
通过project->options->c/c++compiler->extraOptions可以看到协调器所带的配置文件为：
-f $PROJ_DIR$\..\..\..\Tools\CC2430DB\f8wCoord.cfg
-f $PROJ_DIR$\..\..\..\Tools\CC2430DB\f8wConfig.cfg
即编译了ZDO_COORDINATOR和RTR_NWK.
通过project->options->c/c++compiler->Preprocessor->Defined symbols可以看到协调器预编译包含了：
CC2430EB; ZTOOL_P1; MT_TASK; LCD_SUPPORTED=DEBUG; MANAGED_SCAN
没有编译HOLD_AUTO_START和SOFT_START.
2、具体流程
main()->osal_init_system()->osalInitTasks()->ZDApp_Init()
进入ZDApp_Init()函数:
**************************************
void ZDApp_Init( byte task_id )
{
uint8 capabilities;
// Save the task ID
ZDAppTaskID = task_id;
// Initialize the ZDO global device short address storage
ZDAppNwkAddr.addrMode = Addr16Bit;
ZDAppNwkAddr.addr.shortAddr = INVALID_NODE_ADDR; //0xFFFE
(void)NLME_GetExtAddr(); // Load the saveExtAddr pointer.
// Check for manual"Hold Auto Start"
//检测到有手工设置SW_1则会设置devState = DEV_HOLD,从而避开网络初始化
ZDAppCheckForHoldKey();
// Initialize ZDO items and setup the device - type of device to create.
ZDO_Init(); //通过判断预编译来开启一些函数功能
// Register the endpoint description with the AF
// This task doesn't have a Simple description, but we still need
// to register the endpoint.
afRegister( (endPointDesc_t *)&ZDApp_epDesc );
#if defined( ZDO_USERDESC_RESPONSE )
ZDApp_InitUserDesc();
#endif // ZDO_USERDESC_RESPONSE
// set broadcast address mask to support broadcast filtering
NLME_GetRequest(nwkCapabilityInfo, 0, &capabilities);
NLME_SetBroadcastFilter( capabilities );
// Start the device?
if ( devState != DEV_HOLD )
{
ZDOInitDevice( 0 );
}
/*如果devState=DEV_HOLD,则不会调用ZDOInitDevice()来初始化网络
即不组网也不进网.LED4闪烁等待应用程序来开启设备并初始化网络
*/
else
{
// Blink LED to indicate HOLD_START
HalLedBlink ( HAL_LED_4, 0, 50, 500 );
}
ZDApp_RegisterCBs();
}
**************************************
协调器没有编译HOLD_AUTO_START,也没有手工设置SW_1,初始化devState = DEV_INIT(参见基本问题说明3).因此直接在ZDApp_Init()中进入ZDOInitDevice( 0 )开启设备.
**************************************
uint8 ZDOInitDevice( uint16 startDelay )
{
//初始化设备网络状态为ZDO_INITDEV_NEW_NETWORK_STATE:新的网络状态.
//可能意味着ZCD_NV_STARTUP_OPTION不能恢复，或没有任何网络状态恢复
uint8 networkStateNV = ZDO_INITDEV_NEW_NETWORK_STATE;
uint16 extendedDelay = 0;
devState = DEV_INIT; // Remove the Hold state
// Initialize leave control logic
//函数读取NV项目ZCD_NV_LEAVE_CTRL的值,ZDApp_LeaveCtrl指向这个值
ZDApp_LeaveCtrlInit();
// Check leave control reset settings
ZDApp_LeaveCtrlStartup( &devState, &startDelay );
// Leave may make the hold state come back
//以上两个函数设置了对设备离开时的控制,如果有延时则延时,没有则
//把设备状态设为DEV_HOLD
if ( devState == DEV_HOLD )
//ZDO_INITDEV_LEAVE_NOT_STARTED:该设备没有在网络中，下次调用才启用.
return ( ZDO_INITDEV_LEAVE_NOT_STARTED ); // Don't join - (on
#if defined ( NV_RESTORE )
// Get Keypad directly to see if a reset nv is needed.
// Hold down the SW_BYPASS_NV key (defined in On
// while booting(引导) to skip past NV Restore.
if ( HalKeyRead() == SW_BYPASS_NV )
//SW_BYPASS_NV按键处于按下状态时,则避开网络层的NV存储
networkStateNV = ZDO_INITDEV_NEW_NETWORK_STATE; //设备网络状态为新的网络状态
else
{
// Determine if NV should be restored
//函数返回的设备网络状态要么是新的网络状态;要么是恢复的网络状态;以此
//来确定要不要读取NV里相应条目来恢复网络先前状态
networkStateNV = ZDApp_ReadNetworkRestoreState();
}
//如果设备的网络状态为恢复的网络状态
if ( networkStateNV == ZDO_INITDEV_RESTORED_NETWORK_STATE )
{
//恢复设备先前的网络状态参数并且
//设置devStartMode = MODE_RESUME!!!!
networkStateNV = ZDApp_RestoreNetworkState();
}
else //如果设备的网络状态为新的网络状态,在下面进行处理
{
// Wipe out(清除) the network state in NV
NLME_InitNV();
NLME_SetDefaultNV(); //设置默认NV条目
}
#endif
//如果设备的网络状态为新的网络状态
if ( networkStateNV == ZDO_INITDEV_NEW_NETWORK_STATE )
{
//根据预编译来设置设备新的网络状态参数
ZDAppDetermineDeviceType();/*!!!!*/
// On
extendedDelay = (uint16)((NWK_START_DELAY + startDelay)
+ (osal_rand() & EXTENDED_JOINING_RANDOM_MASK));
}
// Initialize device security
ZDApp_SecInit( networkStateNV );
// Trigger the network start
ZDApp_NetworkInit( extendedDelay );
return ( networkStateNV );
}
**************************************
分两种情况:
(1)如果协调器预编译了NV_RESTORE,且函数ZDApp_ReadNetworkRestoreState()返回值为ZDO_INITDEV_RESTORED_NETWORK_STATE,则进入ZDApp_RestoreNetworkState()里设置ZDO_Config_Node_Descriptor.LogicalType = NODETYPE_COORDINATOR和devStartMode = MODE_RESUME.
****************
uint8 ZDApp_RestoreNetworkState( void )
{
…………
// Are we a coordinator
//设备的网络状态为恢复的网络状态.则进入这个函数进行恢复
//先判断如果短地址为0则设置设备逻辑类型为协调器且devStartMode = MODE_RESUME
//否则设置devStartMode = MODE_RESUME
ZDAppNwkAddr.addr.shortAddr = NLME_GetShortAddr();
if ( ZDAppNwkAddr.addr.shortAddr == 0 ) //如果短地址是0,即协调器
{
ZDO_Config_Node_Descriptor.LogicalType = NODETYPE_COORDINATOR; //!!!!!
}
devStartMode = MODE_RESUME; //MODE_RESUME!!!!!!!!
…………
}
****************
(2)如果协调器没有预编译NV_RESTORE,networkStateNV ==ZDO_INITDEV_NEW_NETWORK_STATE,但由于协调器编译了ZDO_COORDINATOR而没有编译SOFT_START,因此ZDAppDetermineDeviceType()不起作用.因此ZDO_Config_Node_Descriptor.LogicalType和devStartMode这两个关键参数保持初始化时的值:
ZDO_Config_Node_Descriptor.LogicalType = NODETYPE_COORDINATOR(见基本问题说明6)
devStartMode = MODE_HARD(见基本问题说明4)
对于协调器,这两种情况最终都是确定两个关键设备网络状态参数的值.对本例的SampleApp的协调器,没有编译NV_RESTORE,因此属于情况(2).
然后调用ZDApp_NetworkInit()启动网络:
****************
void ZDApp_NetworkInit( uint16 delay )
{
if ( delay )
{
// Wait awhile before starting the device
osal_start_timerEx( ZDAppTaskID, ZDO_NETWORK_INIT, delay );
}
else
{
osal_set_event( ZDAppTaskID, ZDO_NETWORK_INIT );
}
}
****************
通过触发ZDAppTaskID的ZDO_NETWORK_INIT事件.来看下对ZDO_NETWORK_INIT 事件的处理:
****************
UINT16 ZDApp_event_loop( byte task_id, UINT16 events )
{
…………
if ( events & ZDO_NETWORK_INIT )
{
// Initialize apps and start the network
devState = DEV_INIT;
ZDO_StartDevice( (uint8)ZDO_Config_Node_Descriptor.LogicalType, devStartMode,
DEFAULT_BEACON_ORDER, DEFAULT_SUPERFRAME_ORDER );
// Return unprocessed events
return (events ^ ZDO_NETWORK_INIT);
}
…………
}
****************
可以看到调用了ZDO_StartDevice( (uint8)ZDO_Config_Node_Descriptor.LogicalType, devStartMode,DEFAULT_BEACON_ORDER, DEFAULT_SUPERFRAME_ORDER );
这里设备网络状态参数:
ZDO_Config_Node_Descriptor.LogicalType = NODETYPE_COORDINATOR
devStartMode = MODE_HARD
且协调器编译了ZDO_COORDINATOR
****************
void ZDO_StartDevice( byte logicalType, devStartModes_t startMode, byte beaconOrder, byte superframeOrder )
{
ZStatus_t ret;
ret = ZUnsupportedMode;
#if defined(ZDO_COORDINATOR)
if ( logicalType == NODETYPE_COORDINATOR )
{
if ( startMode == MODE_HARD ) //MODE_HARD
{
devState = DEV_COORD_STARTING; //Started as Zigbee Coordinator
//建网
ret = NLME_NetworkFormationRequest( zgConfigPANID, zgDefaultChannelList,
zgDefaultStartingScanDuration, beaconOrder,
superframeOrder, false );
}
else if ( startMode == MODE_RESUME ) //MODE_RESUME
{
// Just start the coordinator
devState = DEV_COORD_STARTING;
ret = NLME_StartRouterRequest( beaconOrder, beaconOrder, false );
}
else //错误，未知启动模式
{
#if defined( LCD_SUPPORTED )
//HalLcdWriteScreen( "StartDevice ERR", "MODE unknown" );
ClearScreen();
Print8(HAL_LCD_LINE_1,10,"StartDevice ERR",1);
Print8(HAL_LCD_LINE_2,10,"MODE unknown",1);
#endif
}
}
#endif // !ZDO_COORDINATOR
//#if !defined ( ZDO_COORDINATOR ) || defined( SOFT_START )
if ( logicalType == NODETYPE_ROUTER || logicalType == NODETYPE_DEVICE )
{
if ( (startMode == MODE_JOIN) || (startMode == MODE_REJOIN) )
{
devState = DEV_NWK_DISC; //Discovering PAN's to join
#if defined( MANAGED_SCAN )
ZDOManagedScan_Next();
ret = NLME_NetworkDiscoveryRequest( managedScanChannelMask, BEACON_ORDER_15_MSEC );
#else
ret = NLME_NetworkDiscoveryRequest( zgDefaultChannelList, zgDefaultStartingScanDuration );
#endif
}
else if ( startMode == MODE_RESUME ) //MODE_RESUME 恢复
{
if ( logicalType == NODETYPE_ROUTER )
{
ZMacScanCnf_t scanCnf;
devState = DEV_NWK_ORPHAN;
/* if router and nvram is available, fake successful orphan scan */
scanCnf.hdr.Status = ZSUCCESS;
scanCnf.ScanType = ZMAC_ORPHAN_SCAN;
scanCnf.UnscannedChannels = 0;
scanCnf.ResultListSize = 0;
nwk_ScanJoiningOrphan(&scanCnf);
ret = ZSuccess;
}
else
{
devState = DEV_NWK_ORPHAN; //孤儿
ret = NLME_OrphanJoinRequest( zgDefaultChannelList,
zgDefaultStartingScanDuration );
}
}
else
{
#if defined( LCD_SUPPORTED )
// HalLcdWriteScreen( "StartDevice ERR", "MODE unknown" );
Print8(HAL_LCD_LINE_1,10,"StartDevice ERR",1);
Print8(HAL_LCD_LINE_2,10,"MODE unknown",1);
#endif
}
}
//#endif //!ZDO COORDINATOR || SOFT_START
if ( ret != ZSuccess )
osal_start_timerEx(ZDAppTaskID, ZDO_NETWORK_INIT, NWK_RETRY_DELAY );
}
****************
通过参数可知协调器调用NLME_NetworkFormationRequest( zgConfigPANID, zgDefaultChannelList,
zgDefaultStartingScanDuration, beaconOrder,
superframeOrder, false )
进行网络的组建.
而对NLME_NetworkFormationRequest()的调用会产生一个回调函数ZDO_NetworkFormationConfirmCB()(见主要函数说明3),来看下：
****************
void ZDO_NetworkFormationConfirmCB( ZStatus_t Status )
{
#if defined(ZDO_COORDINATOR)
nwkStatus = (byte)Status;
if ( Status == ZSUCCESS )
{
// LED on shows Coordinator started
HalLedSet ( HAL_LED_3, HAL_LED_MODE_ON );
// LED off forgets HOLD_AUTO_START
HalLedSet (HAL_LED_4, HAL_LED_MODE_OFF);
#if defined ( ZBIT )
SIM_SetColor(0xd0ffd0);
#endif
if ( devState == DEV_HOLD )
{
// Began with HOLD_AUTO_START
devState = DEV_COORD_STARTING;
}
}
#if defined(BLINK_LEDS)
else
HalLedSet ( HAL_LED_3, HAL_LED_MODE_FLASH ); // Flash LED to show failure
#endif
osal_set_event( ZDAppTaskID, ZDO_NETWORK_START );
#endif //ZDO_COORDINATOR
}
****************
如果Status返回ZSUCCESS,建立网络成功,通过一些灯亮来来指示;不成功则通过闪烁灯来指示.最后触发任务ZDAppTaskID的ZDO_NETWORK_START事件,看下对ZDO_NETWORK_START的处理:
****************
#if defined (RTR_NWK)
if ( events & ZDO_NETWORK_START )
{
ZDApp_NetworkStartEvt();
// Return unprocessed events
return (events ^ ZDO_NETWORK_START);
}
****************
调用了ZDApp_NetworkStartEvt()
****************
void ZDApp_NetworkStartEvt( void )
{
if ( nwkStatus == ZSuccess )//网络建立成功
{
// Successfully started a ZigBee network
if ( devState == DEV_COORD_STARTING )
{
devState = DEV_ZB_COORD;
}
osal_pwrmgr_device( PWRMGR_ALWAYS_ON );
osal_set_event( ZDAppTaskID, ZDO_STATE_CHANGE_EVT );
}
else //网络建立不成功,则增加能量阀值重新建网.
{
// Try again with a higher energy threshold !!
if ( ( NLME_GetEnergyThreshold() + ENERGY_SCAN_INCREMENT ) < 0xff )
{
NLME_SetEnergyThreshold( (uint8)(NLME_GetEnergyThreshold() + ENERGY_SCAN_INCREMENT) );
osal_set_event( ZDAppTaskID, ZDO_NETWORK_INIT ); //重新初始化建立网络
}
else
{
// Failed to start network. Enter a dormant state (until user intervenes)
devState = DEV_INIT;
osal_set_event( ZDAppTaskID, ZDO_STATE_CHANGE_EVT );
}
}
}
****************
如果协调器建立网络成功,则触发ZDAppTaskID的ZDO_STATE_CHANGE_EVT事件.看下对 ZDO_STATE_CHANGE_EVT的处理:
****************
if ( events & ZDO_STATE_CHANGE_EVT )
{
ZDO_UpdateNwkStatus( devState );
// Return unprocessed events
return (events ^ ZDO_STATE_CHANGE_EVT);
}
****************
调用了ZDO_UpdateNwkStatus( devState ),网络状态改变,这个函数会更新和发送信息通知每个注册登记过的应用终端.
****************
void ZDO_UpdateNwkStatus( devStates_t state )
{
// Endpoint/Interface descriptor list.
epList_t *epDesc = epList;
byte bufLen = sizeof(osal_event_hdr_t);
osal_event_hdr_t *msgPtr;
ZDAppNwkAddr.addr.shortAddr = NLME_GetShortAddr();
(void)NLME_GetExtAddr(); // Load the saveExtAddr pointer.
while ( epDesc )
{
if ( epDesc->epDesc->endPoint != ZDO_EP )
{
msgPtr = (osal_event_hdr_t *)osal_msg_allocate( bufLen );
if ( msgPtr )
{
msgPtr->event = ZDO_STATE_CHANGE; // Command ID
msgPtr->status = (byte)state;
osal_msg_send( *(epDesc->epDesc->task_id), (byte *)msgPtr ); //发往应用任务
}
}
epDesc = epDesc->nextDesc;
}
}
****************
对SampleApp的协调器来说，这里触发应用任务SampleApp_TaskID的ZDO_STATE_CHANGE事件,看下对ZDO_STATE_CHANGE的处理:
****************
case ZDO_STATE_CHANGE:
SampleApp_NwkState = (devStates_t)(MSGpkt->hdr.status); //获取设备当前状态
if ( (SampleApp_NwkState == DEV_ZB_COORD)
|| (SampleApp_NwkState == DEV_ROUTER)
|| (SampleApp_NwkState == DEV_END_DEVICE) )
{
// Start sending the periodic message in a regular interval.
osal_start_timerEx( SampleApp_TaskID,
SAMPLEAPP_SEND_PERIODIC_MSG_EVT,
SAMPLEAPP_SEND_PERIODIC_MSG_TIMEOUT );
}
else
{
// Device is no longer in the network
}
break;
****************
可以看到当协调器建立网络成功,通过回调函数触发应用任务的ZDO_STATE_CHANGE事件,最终开启定时器发送周期信息.
3、
协调器(自启动模式)—以SampleApp的协调器为例,并假设初始化成功,网络建立成功.
程序大致流程:
main()->osal_init_system()->osalInitTasks()->ZDApp_Init()->ZDOInitDevice()->ZDApp_NetworkInit->触发ZDAppTaskID的ZDO_NETWORK_INIT->ZDO_StartDevice()->NLME_NetworkFormationRequest()->网络建立成功ZDO_NetworkFormationConfirmCB->触发ZDAppTaskID的ZDO_NETWORK_START->ZDApp_NetworkStartEvt()->触发ZDAppTaskID的ZDO_STATE_CHANGE_EVT->ZDO_UpdateNwkStatus()->触发SampleApp_TaskID的ZDO_STATE_CHANGE->开户周期信息发送的定时器.
4、注:
(1)自启动模式下SampleApp的终端和路由器总体流程基本一致.
(2)
以SampleApp为例,ZDO_StartDevice()函数的两个重要参数比较:
终端:
ZDO_Config_Node_Descriptor.LogicalType = NODETYPE_DEVICE
devStartMode = MODE_JOIN
路由器:
ZDO_Config_Node_Descriptor.LogicalType = NODETYPE_ROUTER
devStartMode = MODE_JOIN
协调器:
ZDO_Config_Node_Descriptor.LogicalType = NODETYPE_COORDINATOR
devStartMode = MODE_HARD
***************************************
***************************************
说明：
1、本文为个人学习笔记,纯属个人理解,错误不可避免,仅供参考.随时更新
2、细节基本不管,遇到问题再作分析,程序注释为个人原始注释内容,记录有些仓促.
3、欢迎交流,转载请注明出处,谢谢！
2010.7.09 ~XF
