Chinaunix首页 | 论坛 | 博客
  • 博客访问: 871472
  • 博文数量: 275
  • 博客积分: 3904
  • 博客等级: 中校
  • 技术积分: 4605
  • 用 户 组: 普通用户
  • 注册时间: 2012-04-17 21:10
文章分类

全部博文(275)

文章存档

2014年(9)

2013年(124)

2012年(142)

分类:

2012-07-31 14:12:36

做服务时碰见一问题,一共20多台4503都有这问题4503的机箱,4013+ts引擎.

问题:设备时没有加载IOS而是直接进入rommon模式,开始发现寄存器的值是0x2000就改成了0x2102,反复出现重启多次,还是进入了rommon模式,只有敲入boot的命令才能正常。

提示信息:----------------------------------------------------------------------------------------------------------------
**********************************************************
*                                                        *
* Welcome Rom Monir for   WS-X4013+TS System.       *
* Copyright (c) 2003-2007 by Cisco Systems, Inc.         *
* All rights reserved.                                   *
*                                                        *
**********************************************************

Rom Monitor Program Version 12.2(31r)SGA1
Supervisor: WS-X4013+TS Chassis: WS-C4503
Hardware Revisions - Board: 7.4 CPLD: 4 Dagobah: 226

MAC Address : 00-16-46-c2-14-2b
Ip Address   : Not set.
Netmask      : Not set.
Gateway      : Not set.
TftpServer   : Not set.
Main Memory : 256 MBytes

rommon 1 >

解决方法1:

在ios 的配置里指定启动ios镜像文件的位置,但是一定要注意格式;

     boot system flash bootflash:cat4000-is-mz.121-11b.EW  

“ bootflash:”在系统里没有提示容易忽视,如果不加系统还是不能正常启动。

解决方法2:按照如下步骤来操作:

rommon 1 >?
alias              set and display aliases command
boot               boot up an external process
clear              clear configurations, use 'clear help' for more info
confreg            configuration register utility
dev                list device table with physical device information
dir                list filesystem information
help               monitor builtin command help
history            monitor command history
macstats           print management port MAC statistics counters
meminfo            main memory information
ping               ping utility to determine network connectivity
repeat             repeat a monitor command
reset              system reset
set                show/set environment vars, use 'set help' for more info
sprom              serial eprom operations
sysret             print out info from last system return
unalias            unset an alias
unset              unset a monitor variable
version            display Rom Monitor version information
rommon 2 >confreg

Configuration Summary :
=> load rom after netboot fails
=> break/abort has effect
=> console baud: 9600
=> autoboot from: the first file from internal flash device

do you wish to change the configuration? y/n [n]: y
enable "diagnostic mode"? y/n [n]: n
enable "use net in IP bcast address"? y/n [n]: n
disable "load rom after netboot fails"? y/n [n]: n
enable "use all zero broadcast"? y/n [n]: n
disable "break/abort has effect"? y/n [n]: n
enable "ignore system config info"? y/n [n]: n

change console baud rate? y/n [n]: n

change the boot characteristics? y/n [n]: y

enter to boot:
0 = disable autoboot
1 = the first file from internal flash device
2 = commands specified in 'BOOT' environment variable
[1]: 1

Configuration Summary :
=> load rom after netboot fails
=> break/abort has effect
=> console baud: 9600
=> autoboot from: the first file from internal flash device

do you wish to save this configuration? y/n [n]: y
You must reset or power cycle for new configuration to take effect


rommon 3 >reset

Resetting .......


rommon 4 >

问题解决!

阅读(1238) | 评论(0) | 转发(0) |
给主人留下些什么吧!~~