分类： 服务器与存储
2015-01-29 15:14:50
资料都是惠普网站上能公开下载到的，如果有啥涉及到泄密的地方请联系我，我会及时删除的。
接线示意图
To verify that the resulting vPartition has the expected IO in that slot, simply install and boot HP-UX in that partition and then run ioscan -m resourcepath, searching for the ioslot number (Note: you really have to spell out “-m resourcepath,” it is not a place holder for a number):
# ioscan -m resourcepath | grep 9/1/3
48/0/0/2/0/0 0x90001000203ff85 ioslot-9/1/3
This result can be used in a second call to ioscan to get the IO details:
# ioscan -kf -H 48/0/0/2/0
Class I H/W Path Driver S/W State H/W Type Description
============================================================================
ba 30 48/0/0/2/0 PCItoPCI CLAIMED BUS_NEXUS PCItoPCI Bridge
slot 18 48/0/0/2/0/0 pci_slot CLAIMED SLOT PCI Slot
ba 31 48/0/0/2/0/0/0 PCItoPCI CLAIMED BUS_NEXUS PCItoPCI Bridge
Power supply units
1. Verify which power supply you will need using the show enclosure power supply all
command:
wtec-lc-sd-oa1> show enclosure powersupply all
Power Supply #4 Information:
Status: OK
AC Input Status: OK
Capacity: 2400 Watts
Current Power Output: 837 Watts
Serial Number: 5AGUD0AHLZD25E
Product Name: HP 2400W HE PSU
Part Number: 499253-B21
Spare Part Number: 500242-001
Product Ver: 01
Diagnostic Status:
Internal Data OK
Device Failure OK
Power Cord OK
Indicted OK
CAUTION: Do not mix 92% efficient power supplies (spare part number 500242-001) and
94% efficient power supplies (spare part number 588733-001) in the same compute enclosure.
When adding or replacing a power supply, always verify which power supply you will need.
If the system contains a mixed configuration, a syslog entry, level 3 IPMI event and WS-MAN
alert will be generated.
Power on and boot
1. Power on and boot as a Superdome 2 – 32s system (“Powering up the complex and cable connections” (page 65)).
2. Check the status and configuration with using the following commands:
a. From the OA on Enclosure 1:
show complex status:
show complex info
show topology
show iox list
show hr
show indict
connect exit
b. From the OA of Enclosure 1 and Enclosure 2
show blade list
show xfm list
c. From the OA of Enclosure 2:
set enclosure name
set OA name
d. Run diagnostics from Enclosure 1 with these commands:
OA> show hr
HR> show indict
Acquit any existing indictments.
HR> test fabric
Verify that both xfabric and CAMnet cabling is correct.
DIMM
sd-oa1> show xfm status all
Bay 4 XFM Status:
Health: OK
Power: On
Unit Identification LED: Off
Diagnostic Status:
Internal Data OK
Management Processor OK
Thermal Warning OK
Thermal Danger OK
Power OK <<<<
Firmware Mismatch OK
Indicted OK
Link 1: OK
Link 2: OK
Link 3: OK
Link 4: OK
Link 5: OK
Link 6: OK
Link 7: OK
Link 8: OK
sd-oa1> show blade status all
Blade #1 Status:
Power: On
Current Wattage used: 1325 Watts
Health: OK
Unit Identification LED: Off
Diagnostic Status:
Internal Data OK
Management Processor OK
Thermal Warning OK
Thermal Danger OK
I/O Configuration OK
Power OK <<<
Cooling OK
Device Failure OK
Device Degraded OK
Device Info OK
Firmware Mismatch OK
PDHC OK
Indicted OK
sd-oa1> show interconnect status all
Interconnect Module #1 Status:
Status: OK
Thermal: OK
CPU Fault: OK
Health LED: OK
UID: Off
Powered: On
Diagnostic Status:
Internal Data OK
Management Processor OK
Thermal Warning OK
Thermal Danger OK
I/O Configuration OK
Power OK <<<
Device Failure OK
Device Degraded OK
IOX enclosures
Use the show IOX power all command to gather information on IOX enclosure power:
sd-oa1> show iox power all
IOX 5:
No IOX Installed
IOX 6:
No IOX Installed
IOX 7:
No IOX Installed
IOX 8:
No IOX Installed
IOX 9:
Present Power: 189 Watts AC
IOX 10:
Present Power: 222 Watts AC
IOX 11:
No IOX Installed
IOX 12:
No IOX Installed
To obtain information about failures recorded by the system, use the following commands:
Show cae –L (within HR, run show HR to enter the HR submenu)
sd-oa1> show cae -L
Sl.No Severity EventId EventCategory PartitionId EventTime Summary
################################################################################
71 Critical 3040 System Coo... N/A Fri May 18 06:26:34 2012 XFM air intake or exhaust
temperatur...
70 Critical 3040 System Coo... N/A Fri May 18 04:56:22 2012 XFM air intake or exhaust
temperatur...
show CAE –E -n
Use show CAE –E -n
oa1> show cae -E -n 70
Alert Number : 70
Event Identification :
Event ID : 3040
Provider Name : CPTIndicationProvider
Event Time : Fri May 18 04:56:22 2012
Indication Identifier : 8304020120518045622
Managed Entity :
OA Name : sd-oa1
System Type : 59
System Serial No. : USExxxxxS
OA IP Address : aa.bb.cc.dd
Affected Domain :
Enclosure Name : lc-sd2
RackName : sd2
RackUID : 02SGHxxxxAVY
Impacted Domain : Complex
Complex Name : SD2
Partition ID : Not Applicable
Summary :
XFM air intake or exhaust temperature is too hot
Full Description :
The air temperature measured at one of the XFM air intakes or exhausts is too hot to allow normal
operation. Measures are being taken to increase the cooling ability of the box, and to reduce heat
generation. If the temperature continues to increase, however, partitions may be shut down to prevent
hardware damage.
Probable Cause 1 :
Data center air conditioning is not functioning properly
Recommended Action 1 :
Fix the air conditioning problem
Probable Cause 2 :
The system air intake is blocked
Recommended Action 2 :
Check and unblock air intakes
Replaceable Unit(s) :
Part Manufacturer : HP
Spare Part No. : AH341-67001
Part Serial No. : MYJaaaaaWV
Part Location : 0x0100ff02ff00ff51 enclosure1/xfm2
Additional Info : Not Applicable
Additional Data :
Severity : Critical
Alert Type : Environmental Alert
Event Category : System Cooling
Event Subcategory : Unknown
Probable Cause : Temperature Unacceptable
Event Threshold : 1
Event Time Window (in minutes): 0
Actual Event Threshold : 1
Actual Event Time Window (in minutes): 0
OEM System Model : NA
Original Product Number : AH337A
Current Product Number : AH337A
OEM Serial Number : NA
Version Info :
Complex FW Version : 2.52.2
Provider Version : 3.47
Error Log Data :
Error Log Bundle : 4000000000000e41
XFM注意事项
升级firmware
All partitions update
Use the following command to update all partitions present in the system as well as any blades
that are not currently assigned to any partition:
oa> UPDATE NPARTITION ALL
NOTE: The [FORCE], [REINSTALL], and [NOEXECUTE] command modifiers still apply.
Blade update
Use the following command to update a single blade that is not currently assigned to a partition.
oa> UPDATE NPARTITION BLADE
NOTE: The blade resource path is entered as CHASSIS/SLOT [X/Y]
For example: oa> UPDATE NPARTITION BLADE 1/3 ftp://
启动npar2
poweron partition 2
Poweron request sent to partition 2. Operation initiated successfully.
Please run PARSTATUS/VPARSTATUS or SHOW SYSLOG OA to determine the completion
status of the operation.
