Chinaunix首页 | 论坛 | 博客
  • 博客访问: 1734042
  • 博文数量: 163
  • 博客积分: 10591
  • 博客等级: 上将
  • 技术积分: 1980
  • 用 户 组: 普通用户
  • 注册时间: 2006-08-08 18:17
文章分类

全部博文(163)

文章存档

2018年(1)

2012年(1)

2011年(47)

2010年(58)

2009年(21)

2008年(35)

分类: LINUX

2008-08-01 11:18:05

很久都没有操作都忘的差不多了,重新练练,加深点印象。
这些操作都是在VMWare虚拟机上进行的。首先把RHEL5安装在/dev/sda上。安装完后从添加了四块硬盘,分别是/dev/sdb、/dev/sdc、/dev/sdd、/dev/sde
以root进入系统,首先看一下磁盘的情况:
 

[root@TSM54-Test ~]# fdisk -l


Disk /dev/sda: 15.0 GB, 15032385536 bytes
255 heads, 63 sectors/track, 1827 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes

   Device Boot Start End Blocks Id System
/dev/sda1 * 1 13 104391 83 Linux
/dev/sda2 14 1827 14570955 8e Linux LVM

Disk /dev/sdb: 8589 MB, 8589934592 bytes
255 heads, 63 sectors/track, 1044 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes

   Device Boot Start End Blocks Id System

Disk /dev/sdc: 8589 MB, 8589934592 bytes
255 heads, 63 sectors/track, 1044 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes

   Device Boot Start End Blocks Id System

Disk /dev/sdd: 8589 MB, 8589934592 bytes
255 heads, 63 sectors/track, 1044 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes

   Device Boot Start End Blocks Id System

Disk /dev/sde: 8589 MB, 8589934592 bytes
255 heads, 63 sectors/track, 1044 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes

   Device Boot Start End Blocks Id System

一.创建Soft RAID

1.创建raid分区

[root@TSM54-Test ~]# fdisk /dev/sdb

The number of cylinders for this disk is set to 1044.
There is nothing wrong with that, but this is larger than 1024,
and could in certain setups cause problems with:
1) software that runs at boot time (e.g., old versions of LILO)
2) booting and partitioning software from other OSs
   (e.g., DOS FDISK, OS/2 FDISK)

Command (m for help): n
Command action
   e extended
   p  primary partition (1-4)
p
Partition number (1-4): 1
First cylinder (1-1044, default 1):
Using default value 1
Last cylinder or +size or +sizeM or +sizeK (1-1044, default 1044):
Using default value 1044

Command (m for help): t
Selected partition 1
Hex code (type L to list codes): L

 0  Empty           1e  Hidden W95 FAT1 80  Old Minix       be  Solaris boot
 1  FAT12           24  NEC DOS         81  Minix / old Lin bf  Solaris
 2  XENIX root      39  Plan 9          82  Linux swap / So c1  DRDOS/sec (FAT-
 3  XENIX usr       3c  PartitionMagic  83  Linux           c4  DRDOS/sec (FAT-
 4  FAT16 <32M      40  Venix 80286     84  OS/2 hidden C:  c6  DRDOS/sec (FAT-
 5  Extended        41  PPC PReP Boot   85  Linux extended  c7  Syrinx
 6  FAT16           42  SFS             86  NTFS volume set da  Non-FS data
 7  HPFS/NTFS       4d  QNX4.x          87  NTFS volume set db  CP/M / CTOS / .
 8  AIX             4e  QNX4.x 2nd part 88  Linux plaintext de  Dell Utility
 9  AIX bootable    4f  QNX4.x 3rd part 8e  Linux LVM       df  BootIt
 a  OS/2 Boot Manag 50  OnTrack DM      93  Amoeba          e1  DOS access
 b  W95 FAT32       51  OnTrack DM6 Aux 94  Amoeba BBT      e3  DOS R/O
 c  W95 FAT32 (LBA) 52  CP/M            9f  BSD/OS          e4  SpeedStor
 e  W95 FAT16 (LBA) 53  OnTrack DM6 Aux a0  IBM Thinkpad hi eb  BeOS fs
 f  W95 Ext'd (LBA) 54  OnTrackDM6      a5  FreeBSD         ee  EFI GPT
10  OPUS            55  EZ-Drive        a6  OpenBSD         ef  EFI (FAT-12/16/
11  Hidden FAT12    56  Golden Bow      a7  NeXTSTEP        f0  Linux/PA-RISC b
12  Compaq diagnost 5c  Priam Edisk     a8  Darwin UFS      f1  SpeedStor
14  Hidden FAT16 <3 61  SpeedStor       a9  NetBSD          f4  SpeedStor
16  Hidden FAT16    63  GNU HURD or Sys ab  Darwin boot     f2  DOS secondary
17  Hidden HPFS/NTF 64  Novell Netware  b7  BSDI fs         fd  Linux raid auto
18  AST SmartSleep  65  Novell Netware  b8  BSDI swap       fe  LANstep
1b  Hidden W95 FAT3 70  DiskSecure Mult bb  Boot Wizard hid ff  BBT
1c  Hidden W95 FAT3 75  PC/IX

Hex code (type L to list codes): fd
Changed system type of partition 1 to fd (Linux raid autodetect)

Command (m for help): p

Disk /dev/sdb: 8589 MB, 8589934592 bytes
255 heads, 63 sectors/track, 1044 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes

   Device Boot      Start         End      Blocks   Id  System
/dev/sdb1               1        1044     8385898+  fd  Linux raid autodetect

Command (m for help): w
The partition table has been altered!

Calling ioctl() to re-read partition table.
Syncing disks.

按照上面的方法分别把/dev/sdc,/dev/sdd/也创建raid分区。完成后,用fdisk -l查看                

[root@TSM54-Test ~]# fdisk -l


Disk /dev/sda: 15.0 GB, 15032385536 bytes
255 heads, 63 sectors/track, 1827 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes

   Device Boot Start End Blocks Id System
/dev/sda1 * 1 13 104391 83 Linux
/dev/sda2 14 1827 14570955 8e Linux LVM

Disk /dev/sdb: 8589 MB, 8589934592 bytes
255 heads, 63 sectors/track, 1044 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes

   Device Boot Start End Blocks Id System
/dev/sdb1 1 1044 8385898+ fd Linux raid autodetect

Disk /dev/sdc: 8589 MB, 8589934592 bytes
255 heads, 63 sectors/track, 1044 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes

   Device Boot Start End Blocks Id System

/dev/sdc1 1 1044 8385898+ fd Linux raid autodetect

Disk /dev/sdd: 8589 MB, 8589934592 bytes
255 heads, 63 sectors/track, 1044 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes

   Device Boot Start End Blocks Id System
/dev/sdd1 1 1044 8385898+ fd Linux raid autodetect

Disk /dev/sde: 8589 MB, 8589934592 bytes
255 heads, 63 sectors/track, 1044 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes

   Device Boot Start End Blocks Id System

2.创建阵列

mdadm可以支持LINEAR、RAID0  (striping)、 RAID1(mirroring)、 RAID4、RAID5、RAID6和MULTIPATH的阵列模式。

命令格式:

mdadm --create device -chunk=X --level=Y --raid-devices=Z devices

[root@TSM54-Test ~]# mdadm --create /dev/md0 --level=5 --raid-devices=3 /dev/sdb /dev/sdc /dev/sdd

mdadm: array /dev/md0 started.

--level表示创建的阵列模式,--raid-devices表示参与阵列的磁盘数量

3.配置文件

[root@TSM54-Test ~]#cp /usr/share/doc/mdadm-2.5.4/mdadm.conf-example /etc/mdadm.conf

[root@TSM54-Test ~]#echo DEVICE /dev/sd[bcd]1 >>/etc/mdadm.conf

[root@TSM54-Test ~]#mdadm -Ds >>/etc/mdadm.conf

4.格式化Raid

接下来,只要把/dev/md0作为一个单独的磁盘设备进行操作就可以:

[root@TSM54-Test ~]# mkfs.ext3 /dev/md0

mke2fs 1.39 (29-May-2006)
Filesystem label=
OS type: Linux
Block size=4096 (log=2)
Fragment size=4096 (log=2)

2097152 inodes, 4194272 blocks
209713 blocks (5.00%) reserved for the super user
First data block=0
Maximum filesystem blocks=0
128 block groups
32768 blocks per group, 32768 fragments per group
16384 inodes per group
Superblock backups stored on blocks:
        32768, 98304, 163840, 229376, 294912, 819200, 884736, 1605632, 2654208,
        4096000

Writing inode tables: done
Creating journal (32768 blocks): done
Writing superblocks and filesystem accounting information: done

This filesystem will be automatically checked every 36 mounts or
180 days, whichever comes first. Use tune2fs -c or -i to override.
[root@TSM54-Test ~]# mkdir /mnt/software

[root@TSM54-Test ~]# mount /dev/md0 /mnt/software

5. 开机自动挂载

更改/etc/fstab文件,添加一行

/dev/md0 /mnt/software ext3 defaults 0 0

 
二. 其他的操作
 
mdadm有7中模式,下面列出了7种模式的命令格式,详细的选项,请参考man手册。
ASSEMBLE MODE :madam --assemble md-device options-and-component-devices
               mdadm --assembel --scan md-devices-and-options
               mdamd --assembel --scan options
BUILD MODE:    mdadm --build device --chunk=X --level=Y --raid-devices=Z devices
CREATE MODE:   mdadm --create device --chunk=X --level=Y --raid-devices=Z devices
MANAGE MODE:   mdadm device options devices
MISC MODE:     mdadm options ... devices ...
MONITOR MODE:  mdadm --monitor options... devices...
GROW MODE:    
 
1.查看
MISC模式

#mdadm --detail /dev/md0
#mdadm -D /dev/md0

2.停止

MISC模式

#mdadm -S /dev/md0

3.启动

ASSEMBLE模式

#mdadm -A /dev/md0 /dev/sd[bcd]1

启动指定的RAID,可以理解为将一个raid重新装配到系统中。
如果在前面已经配置了/etc/mdadm.conf文件,可以使用:
#mdadm -As /dev/md0

4.添加删除磁盘

mdadm可以在Manage模式下,对运行中的阵列进行添加及删除磁盘。常用于标识failed磁盘,增加spare(冗余)磁盘,以及替换磁盘等。

[root@TSM54-Test ~]# mdadm /dev/md0 --fail /dev/sdd --remove /dev/sdd

mdadm: set /dev/sdd faulty in /dev/md0
mdadm: hot removed /dev/sdd
[root@TSM54-Test ~]# mdadm -D /dev/md0

/dev/md0:
        Version : 00.90.03
  Creation Time : Fri Aug 1 21:35:31 2008
     Raid Level : raid5
     Array Size : 16777088 (16.00 GiB 17.18 GB)
    Device Size : 8388544 (8.00 GiB 8.59 GB)
   Raid Devices : 3
  Total Devices : 2
Preferred Minor : 0
    Persistence : Superblock is persistent

    Update Time : Fri Aug 1 23:34:12 2008
          State : clean, degraded
 Active Devices : 2
Working Devices : 2
 Failed Devices : 0
  Spare Devices : 0

         Layout : left-symmetric
     Chunk Size : 64K

           UUID : 28a22990:eac5c231:3fe907f1:1145e264
         Events : 0.6

    Number Major Minor RaidDevice State
       0 8 16 0 active sync /dev/sdb
       1 8 32 1 active sync /dev/sdc
       2 0 0 2 removed
[root@TSM54-Test ~]# mdadm /dev/md0 --add /dev/sdd

mdadm: re-added /dev/sdd
[root@TSM54-Test ~]# mdadm -D /dev/md0

/dev/md0:
        Version : 00.90.03
  Creation Time : Fri Aug 1 21:35:31 2008
     Raid Level : raid5
     Array Size : 16777088 (16.00 GiB 17.18 GB)
    Device Size : 8388544 (8.00 GiB 8.59 GB)
   Raid Devices : 3
  Total Devices : 3
Preferred Minor : 0
    Persistence : Superblock is persistent

    Update Time : Fri Aug 1 23:34:12 2008
          State : clean, degraded, recovering
 Active Devices : 2
Working Devices : 3
 Failed Devices : 0
  Spare Devices : 1

         Layout : left-symmetric
     Chunk Size : 64K

 Rebuild Status : 0% complete

           UUID : 28a22990:eac5c231:3fe907f1:1145e264
         Events : 0.6

    Number Major Minor RaidDevice State
       0 8 16 0 active sync /dev/sdb
       1 8 32 1 active sync /dev/sdc
       2 8 48 2 spare rebuilding /dev/sdd

--fail指定坏磁盘,--remove移走。

需要注意的是,对于某些RAID级别,如RAID0,是不能用--fail --remove --add的。

5.监控

MONITOR模式

# nohup mdadm --monitor --mail root --delay 200 /dev/md0 &

每200秒监控一次,当RAID出现错误时,发送邮件给root用户。

6.增加spare磁盘

可以通过在创建的时候指定冗余磁盘

#mdadm --create --verbose /dev/md0 --level=3 --raid-devices=3 -x1 /dev/sdb1 /dev/sdc1 /dev/sdd1 /dev/sde1

-x(--spare-devices=)参数指定冗余磁盘的数量。另外,对于full的阵列(例如已经有2个磁盘的RAID1),则直接使用-add参数,mdadm会自动把冗余的磁盘作为spare disk。

7.删除RAID

#mdadm -S /dev/md0

#rm /dev/md0
删除/etc/mdadm.conf文件;去除/etc/fstab文件中相关的行。
最后,用fdisk对磁盘进行重新分区。

 

三 RAID之上建立LVM
 
1.前面还有一个/dev/sde没有处理,下面先把它建立成一个RAID1
 

[root@TSM54-Test ~]# fdisk /dev/sde

The number of cylinders for this disk is set to 1044.
There is nothing wrong with that, but this is larger than 1024,
and could in certain setups cause problems with:
1) software that runs at boot time (e.g., old versions of LILO)
2) booting and partitioning software from other OSs
   (e.g., DOS FDISK, OS/2 FDISK)

Command (m for help): p

Disk /dev/sde: 8589 MB, 8589934592 bytes
255 heads, 63 sectors/track, 1044 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes

   Device Boot Start End Blocks Id System

Command (m for help): n
Command action
   e extended
   p primary partition (1-4)
p
Partition number (1-4): 1
First cylinder (1-1044, default 1):
Using default value 1
Last cylinder or +size or +sizeM or +sizeK (1-1044, default 1044): +5000M
Command (m for help): n
Command action
   e extended
   p primary partition (1-4)
p
Partition number (1-4): 2
First cylinder (610-1044, default 610):
Using default value 610
Last cylinder or +size or +sizeM or +sizeK (610-1044, default 1044):
Using default value 1044

Command (m for help): p

Disk /dev/sde: 8589 MB, 8589934592 bytes
255 heads, 63 sectors/track, 1044 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes

   Device Boot Start End Blocks Id System
/dev/sde1 1 609 4891761 83 Linux
/dev/sde2 610 1044 3494137+ 83 Linux

Command (m for help): t
Partition number (1-4): 1
Hex code (type L to list codes): fd
Changed System type of partition 1 to fd (Linux raid autodetect)

Command (m for help): t
Partition number (1-4): 2
Hex code (type L to list codes): fd
Changed System type of partition 2 to fd (Linux raid autodetect)

Command (m for help): p

Disk /dev/sde: 8589 MB, 8589934592 bytes
255 heads, 63 sectors/track, 1044 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes

   Device Boot Start End Blocks Id System

/dev/sde1 1 609 4891761 fd Linux raid autodetect
/dev/sde2 610 1044 3494137+ fd Linux raid autodetect

Command (m for help): w
The partition table has been

Calling ioctl() to re-read partition table.
Syncing disks.

完成分区后,执行:

[root@TSM54-Test dev]# cd /dev/
[root@TSM54-Test dev]# ls -l md0
brw-r----- 1 root disk 9, 0 Aug 1 21:58 md0
[root@TSM54-Test dev]# mknod md1 b 9 1
[root@TSM54-Test dev]# mdadm --create /dev/md1 --level=1 --raid-devices=2 /dev/sde1 /dev/sde2
mdadm: largest drive (/dev/sde1) exceed size (3494016K) by more than 1%
Continue creating array? y
mdadm: array /dev/md1 started.

好了,RAID1也做完了,验证一下

[root@TSM54-Test dev]# mdadm -Ds
ARRAY /dev/md0 level=raid5 num-devices=3 UUID=28a22990:eac5c231:3fe907f1:1145e264
ARRAY /dev/md1 level=raid1 num-devices=2 UUID=57f24dd1:aed3606c:d467132e:a6b3a010

2. 开始建立LVM

首先确保/dev/md0已经卸载,使用#umount /mnt/software

(1)创建PV

[root@TSM54-Test ~]# pvcreate /dev/md0
  Physical volume "/dev/md0" successfully created
[root@TSM54-Test ~]# pvcreate /dev/md1
  Physical volume "/dev/md1" successfully created
[root@TSM54-Test ~]# pvdisplay
  --- Physical volume ---
  PV Name /dev/sda2
  VG Name VolGroup00
  PV Size 13.90 GB / not usable 21.45 MB
  Allocatable yes (but full)
  PE Size (KByte) 32768
  Total PE 444
  Free PE 0
  Allocated PE 444
  PV UUID BntsgG-UJLv-agT2-lZ7C-dXY2-51FB-Jxd5tA

  --- NEW Physical volume ---
  PV Name /dev/md0
  VG Name
  PV Size 16.00 GB
  Allocatable NO
  PE Size (KByte) 0
  Total PE 0
  Free PE 0
  Allocated PE 0
  PV UUID GriJk2-wyfl-o0CI-NY7t-g75X-zIx3-FJHf1u

  --- NEW Physical volume ---
  PV Name /dev/md1
  VG Name
  PV Size 3.33 GB
  Allocatable NO
  PE Size (KByte) 0
  Total PE 0
  Free PE 0
  Allocated PE 0
  PV UUID SImCO1-RmvK-OgfZ-dCFZ-LJNC-8wun-Bd9qzS

(2)创建VG

[root@TSM54-Test ~]# vgcreate LVMonRaid /dev/md0 /dev/md1

  Volume group "LVMonRaid" successfully created
[root@TSM54-Test ~]# vgscan
  Reading all physical volumes. This may take a while...
  Found volume group "VolGroup00" using metadata type lvm2
  Found volume group "LVMonRaid" using metadata type lvm2

创建了一个LVMonRaid的卷组。

(3)创建LV

[root@TSM54-Test ~]# lvcreate --size 5000M --name LogicLV1 LVMonRaid
  Logical volume "LogicLV1" created
[root@TSM54-Test ~]# lvcreate --size 5000M --name LogicLV2 LVMonRaid
  Logical volume "LogicLV2" created
[root@TSM54-Test ~]# lvscan
  ACTIVE '/dev/VolGroup00/LogVol00' [12.88 GB] inherit
  ACTIVE '/dev/VolGroup00/LogVol01' [1.00 GB] inherit
  ACTIVE '/dev/LVMonRaid/LogicLV1' [4.88 GB] inherit
  ACTIVE '/dev/LVMonRaid/LogicLV2' [4.88 GB] inherit

注:上面两条记录是装系统时默认创建的。

(4)格式化创建文件系统,并挂载使用

[root@TSM54-Test ~]# mkfs.ext3 /dev/LVMonRaid/LogicLV1
mke2fs 1.39 (29-May-2006)
Filesystem label=
OS type: Linux
Block size=4096 (log=2)
Fragment size=4096 (log=2)
640000 inodes, 1280000 blocks
64000 blocks (5.00%) reserved for the super user
First data block=0
Maximum filesystem blocks=1312817152
40 block groups
32768 blocks per group, 32768 fragments per group
16000 inodes per group
Superblock backups stored on blocks:
        32768, 98304, 163840, 229376, 294912, 819200, 884736

Writing inode tables: done
Creating journal (32768 blocks): done
Writing superblocks and filesystem accounting information: done

This filesystem will be automatically checked every 35 mounts or
180 days, whichever comes first. Use tune2fs -c or -i to override.

[root@TSM54-Test ~]# mkfs.ext3 /dev/LVMonRaid/LogicLV2
mke2fs 1.39 (29-May-2006)
Filesystem label=
OS type: Linux
Block size=4096 (log=2)
Fragment size=4096 (log=2)
640000 inodes, 1280000 blocks
64000 blocks (5.00%) reserved for the super user
First data block=0
Maximum filesystem blocks=1312817152
40 block groups
32768 blocks per group, 32768 fragments per group
16000 inodes per group
Superblock backups stored on blocks:
        32768, 98304, 163840, 229376, 294912, 819200, 884736

Writing inode tables: done
Creating journal (32768 blocks): done
Writing superblocks and filesystem accounting information: done

This filesystem will be automatically checked every 33 mounts or
180 days, whichever comes first. Use tune2fs -c or -i to override.

[root@TSM54-Test ~]# mkdir /mnt/doc
[root@TSM54-Test ~]# mkdir /mnt/music
[root@TSM54-Test ~]# mount -t ext3 /dev/LVMonRaid/LogicLV1 /mnt/doc
[root@TSM54-Test ~]# mount -t ext3 /dev/LVMonRaid/LogicLV2 /mnt/music

 

如果要开机自动挂载,更改/etc/fstab文件,添加如下两行:

/dev/LVMonRaid/LogicLV1     /mnt/doc   ext3   defaults     0    0

/dev/LVMonRaid/LogicLV2     /mnt/music  ext3   defaults    0    0

阅读(1957) | 评论(2) | 转发(0) |
给主人留下些什么吧!~~

benxiong2008-09-05 11:31:26

在vmware里安装完操作系统后,关闭新安装的rhel5。在RHEL5的标签下有一个“Edit virtual machine settings",点击进入hardware配置页面,点击”Add”,接下来添加一个新的虚拟硬盘。重复上面的步骤四次,就添加了四块虚拟硬盘。:)

vcdog2008-08-22 09:30:17

安装完后从添加了四块硬盘,分别是/dev/sdb、/dev/sdc、/dev/sdd、/dev/sde 。这一点有点不明白,怎么添加四块硬盘,也是虚拟的硬盘吗??