全部博文（395）
分类：
2011-05-08 15:48:49
Switch>enable //进入特权模式
Switch#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#
Switch(config)#
Switch(config)#
Switch(config)#
%SYS-5-CONFIG_I: Configured from console by console
Switch#
Switch con0 is now available
Press RETURN to get started.
Switch>enable
Switch#configure terminal //进入全局模式
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#exit
%SYS-5-CONFIG_I: Configured from console by console
Switch#?
Exec commands:
<1-99> Session number to resume
clear Reset functions
clock Manage the system clock
configure Enter configuration mode
connect Open a terminal connection
copy Copy from one file to another
debug Debugging functions (see also 'undebug')
delete Delete a file
dir List files on a filesystem
disable Turn off privileged commands
disconnect Disconnect an existing network connection
enable Turn on privileged commands
erase Erase a filesystem
exit Exit from the EXEC
logout Exit from the EXEC
more Display the contents of a file
no Disable debugging informations
ping Send echo messages
reload Halt and perform a cold restart
resume Resume an active network connection
setup Run the SETUP command facility
show Show running system information
telnet Open a telnet connection
terminal Set terminal line parameters
traceroute Trace route to destination
undebug Disable debugging functions (see also 'debug')
vlan Configure VLAN parameters
write Write running configuration to memory, network, or terminal
Switch#exit
Switch>?
Exec commands:
<1-99> Session number to resume
connect Open a terminal connection
disconnect Disconnect an existing network connection
enable Turn on privileged commands
exit Exit from the EXEC
logout Exit from the EXEC
ping Send echo messages
resume Resume an active network connection
show Show running system information
telnet Open a telnet connection
terminal Set terminal line parameters
traceroute Trace route to destination
Switch>e
Switch>en
Switch>enable
Switch#?
Exec commands:
<1-99> Session number to resume
clear Reset functions
clock Manage the system clock
configure Enter configuration mode
connect Open a terminal connection
copy Copy from one file to another
debug Debugging functions (see also 'undebug')
delete Delete a file
dir List files on a filesystem
disable Turn off privileged commands
disconnect Disconnect an existing network connection
enable Turn on privileged commands
erase Erase a filesystem
exit Exit from the EXEC
logout Exit from the EXEC
more Display the contents of a file
no Disable debugging informations
ping Send echo messages
reload Halt and perform a cold restart
resume Resume an active network connection
setup Run the SETUP command facility
Switch#config t
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#?
Configure commands:
banner Define a login banner
boot Boot Commands
cdp Global CDP configuration subcommands
clock Configure time-of-day clock
do To run exec commands in config mode
enable Modify enable password parameters
end Exit from configure mode
exit Exit from configure mode
hostname Set system's network name
interface Select an interface to configure
ip Global IP configuration subcommands
line Configure a terminal line
mac-address-table Configure the MAC address table
no Negate a command or set its defaults
service Modify use of network based services
spanning-tree Spanning Tree Subsystem
username Establish User Name Authentication
vlan Vlan commands
vtp Configure global VTP state
Switch(config)#interface
Switch(config)#interface ?
Ethernet IEEE 802.3
FastEthernet FastEthernet IEEE 802.3
GigabitEthernet GigabitEthernet IEEE 802.3z
Vlan Catalyst Vlans
range interface range command
Switch(config)#interface
% Incomplete command.
Switch(config)#interface FastEnternet
^
% Invalid input detected at '^' marker.
Switch(config)#
Switch(config)#interface FastEthernet
% Incomplete command.
Switch(config)#interface Fast0/1
Switch(config-if)#exit
Switch(config)#?
Configure commands:
banner Define a login banner
boot Boot Commands
cdp Global CDP configuration subcommands
clock Configure time-of-day clock
do To run exec commands in config mode
enable Modify enable password parameters
end Exit from configure mode
exit Exit from configure mode
hostname Set system's network name
interface Select an interface to configure
ip Global IP configuration subcommands
line Configure a terminal line
mac-address-table Configure the MAC address table
no Negate a command or set its defaults
service Modify use of network based services
spanning-tree Spanning Tree Subsystem
username Establish User Name Authentication
vlan Vlan commands
vtp Configure global VTP state
Switch(config)#hostname CoreSW //对交换机进行重命名
CoreSW(config)#?
Configure commands:
banner Define a login banner
boot Boot Commands
cdp Global CDP configuration subcommands
clock Configure time-of-day clock
do To run exec commands in config mode
enable Modify enable password parameters
end Exit from configure mode
exit Exit from configure mode
hostname Set system's network name
interface Select an interface to configure
ip Global IP configuration subcommands
line Configure a terminal line
mac-address-table Configure the MAC address table
no Negate a command or set its defaults
service Modify use of network based services
spanning-tree Spanning Tree Subsystem
username Establish User Name Authentication
vlan Vlan commands
vtp Configure global VTP state
CoreSW(config)#vlan 10 //全局模式下进行vlan的设置
CoreSW(config-vlan)#name Math
CoreSW(config-vlan)#exit
CoreSW(config)#exit
%SYS-5-CONFIG_I: Configured from console by console
CoreSW#?
Exec commands:
<1-99> Session number to resume
clear Reset functions
clock Manage the system clock
configure Enter configuration mode
connect Open a terminal connection
copy Copy from one file to another
debug Debugging functions (see also 'undebug')
delete Delete a file
dir List files on a filesystem
disable Turn off privileged commands
disconnect Disconnect an existing network connection
enable Turn on privileged commands
erase Erase a filesystem
exit Exit from the EXEC
logout Exit from the EXEC
more Display the contents of a file
no Disable debugging informations
ping Send echo messages
reload Halt and perform a cold restart
resume Resume an active network connection
setup Run the SETUP command facility
show Show running system information
telnet Open a telnet connection
terminal Set terminal line parameters
traceroute Trace route to destination
undebug Disable debugging functions (see also 'debug')
vlan Configure VLAN parameters
write Write running configuration to memory, network, or terminal
CoreSW#vlan database
% Warning: It is recommended to configure VLAN from config mode,
as VLAN database mode is being deprecated. Please consult user
documentation for configuring VTP/VLAN in config mode.
CoreSW(vlan)#
%SYS-5-CONFIG_I: Configured from console by console
CoreSW#
CoreSW#
CoreSW#
CoreSW#
CoreSW#valan database //database模式下进行vlan的设置
^
% Invalid input detected at '^' marker.
CoreSW#vlan database
% Warning: It is recommended to configure VLAN from config mode,
as VLAN database mode is being deprecated. Please consult user
documentation for configuring VTP/VLAN in config mode.
CoreSW(vlan)#vlan 20 name Chinese
VLAN 20 added:
Name: Chinese
CoreSW(vlan)#vlan 30 name OtherO
VLAN 30 added:
Name: Other
CoreSW(vlan)#exit
APPLY completed.
Exiting....
CoreSW#en
CoreSW#conf t
Enter configuration commands, one per line. End with CNTL/Z.
CoreSW>en
CoreSW#conf t
Enter configuration commands, one per line. End with CNTL/Z.
CoreSW(config)#interface fa0/1
CoreSW(config-if)#?
cdp Global CDP configuration subcommands
description Interface specific description
duplex Configure duplex operation.
exit Exit from interface configuration mode
mac-address Manually set interface MAC address
no Negate a command or set its defaults
shutdown Shutdown the selected interface
spanning-tree Spanning Tree Subsystem
speed Configure speed operation.
switchport Set switching mode characteristics
CoreSW(config-if)#
CoreSW>en
CoreSW#show interface
CoreSW#show interfaces ?
Ethernet IEEE 802.3
FastEthernet FastEthernet IEEE 802.3
GigabitEthernet GigabitEthernet IEEE 802.3z
Vlan Catalyst Vlans
switchport Show interface switchport information
trunk Show interface trunk information
CoreSW#show interfaces summ
CoreSW#show interfaces summ
CoreSW#show interfaces summary vlan
^
% Invalid input detected at '^' marker.
CoreSW#dis cu
% Ambiguous command: "dis cu"
CoreSW#?
Exec commands:
<1-99> Session number to resume
clear Reset functions
clock Manage the system clock
configure Enter configuration mode
connect Open a terminal connection
copy Copy from one file to another
debug Debugging functions (see also 'undebug')
delete Delete a file
dir List files on a filesystem
disable Turn off privileged commands
disconnect Disconnect an existing network connection
enable Turn on privileged commands
erase Erase a filesystem
exit Exit from the EXEC
logout Exit from the EXEC
more Display the contents of a file
no Disable debugging informations
ping Send echo messages
reload Halt and perform a cold restart
resume Resume an active network connection
setup Run the SETUP command facility
show Show running system information
telnet Open a telnet connection
terminal Set terminal line parameters
traceroute Trace route to destination
undebug Disable debugging functions (see also 'debug')
vlan Configure VLAN parameters
write Write running configuration to memory, network, or terminal
CoreSW#show ?
arp Arp table
boot show boot attributes
cdp CDP information
clock Display the system clock
dtp DTP information
flash: display information about flash: file system
history Display the session command history
hosts IP domain-name, lookup style, nameservers, and host table
interfaces Interface status and configuration
ip IP information
mac-address-table MAC forwarding table
port-security Show secure port information
processes Active process statistics
running-config Current operating configuration
sessions Information about Telnet connections
spanning-tree Spanning tree topology
startup-config Contents of startup configuration
tcp Status of TCP connections
terminal Display terminal configuration parameters
users Display information about terminal lines
version System hardware and software status
vlan VTP VLAN status
vtp VTP information
CoreSW#show vlan ?
brief VTP all VLAN status in brief
id VTP VLAN status by VLAN id
name VTP VLAN status by VLAN name
CoreSW#show vlan //显示当前的vlan信息
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Fa0/1, Fa0/2, Fa0/3, Fa0/4
Fa0/5, Fa0/6, Fa0/7, Fa0/8
Fa0/9, Fa0/10, Fa0/11, Fa0/12
Fa0/13, Fa0/14, Fa0/15, Fa0/16
Fa0/17, Fa0/18, Fa0/19, Fa0/20
Fa0/21, Fa0/22, Fa0/23, Fa0/24
Gig1/1, Gig1/2
10 Math active
20 Chinese active
30 Other active
1002 fddi-default active
1003 token-ring-default active
1004 fddinet-default active
1005 trnet-default active
VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
1 enet 100001 1500 - - - - - 0 0
10 enet 100010 1500 - - - - - 0 0
20 enet 100020 1500 - - - - - 0 0
30 enet 100030 1500 - - - - - 0 0
1002 enet 101002 1500 - - - - - 0 0
1003 enet 101003 1500 - - - - - 0 0
1004 enet 101004 1500 - - - - - 0 0
1005 enet 101005 1500 - - - - - 0 0
CoreSW#show vlan ?
brief VTP all VLAN status in brief
id VTP VLAN status by VLAN id
name VTP VLAN status by VLAN name
CoreSW#show vlan id
% Incomplete command.
CoreSW#show vlan brief
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Fa0/1, Fa0/2, Fa0/3, Fa0/4
Fa0/5, Fa0/6, Fa0/7, Fa0/8
Fa0/9, Fa0/10, Fa0/11, Fa0/12
Fa0/13, Fa0/14, Fa0/15, Fa0/16
Fa0/17, Fa0/18, Fa0/19, Fa0/20
Fa0/21, Fa0/22, Fa0/23, Fa0/24
Gig1/1, Gig1/2
10 Math active
20 Chinese active
30 Other active
1002 fddi-default active
1003 token-ring-default active
1004 fddinet-default active
1005 trnet-default active
CoreSW#en
CoreSW#conf t
Enter configuration commands, one per line. End with CNTL/Z.
CoreSW(config)#interface fa0/1 //设置某个接口在某个vlan下
CoreSW(config-if)#?
cdp Global CDP configuration subcommands
description Interface specific description
duplex Configure duplex operation.
exit Exit from interface configuration mode
mac-address Manually set interface MAC address
no Negate a command or set its defaults
shutdown Shutdown the selected interface
spanning-tree Spanning Tree Subsystem
speed Configure speed operation.
switchport Set switching mode characteristics
CoreSW(config-if)#switchport mode access //这下面两句是一起使用的，这一句是说明在access模式下进行配置
CoreSW(config-if)#switchport access vlan 10 //把当前接口配置在vlan id为10下
CoreSW(config-if)#int
% Incomplete command.
CoreSW(config)#?
Configure commands:
banner Define a login banner
boot Boot Commands
cdp Global CDP configuration subcommands
clock Configure time-of-day clock
do To run exec commands in config mode
enable Modify enable password parameters
end Exit from configure mode
exit Exit from configure mode
hostname Set system's network name
interface Select an interface to configure
ip Global IP configuration subcommands
line Configure a terminal line
mac-address-table Configure the MAC address table
no Negate a command or set its defaults
service Modify use of network based services
spanning-tree Spanning Tree Subsystem
username Establish User Name Authentication
vlan Vlan commands
vtp Configure global VTP state
CoreSW(config)#interface fa0/7
CoreSW(config-if)#switchport
CoreSW(config-if)#switchport
CoreSW(config-if)#switchport mod
CoreSW(config-if)#switchport ?
access Set access mode characteristics of the interface
mode Set trunking mode of the interface
native Set trunking native characteristics when interface is in
trunking mode
nonegotiate Device will not engage in negotiation protocol on this
interface
port-security Security related command
trunk Set trunking characteristics of the interface
voice Voice appliance attributes
CoreSW(config-if)#switchport mode access
CoreSW(config-if)#switchport access vlan 10
CoreSW(config-if)#?
cdp Global CDP configuration subcommands
description Interface specific description
duplex Configure duplex operation.
exit Exit from interface configuration mode
mac-address Manually set interface MAC address
no Negate a command or set its defaults
shutdown Shutdown the selected interface
spanning-tree Spanning Tree Subsystem
speed Configure speed operation.
switchport Set switching mode characteristics
CoreSW(config-if)#interface ?
% Unrecognized command
CoreSW(config-if)#interface
% Incomplete command.
CoreSW(config)#?
Configure commands:
banner Define a login banner
boot Boot Commands
cdp Global CDP configuration subcommands
clock Configure time-of-day clock
do To run exec commands in config mode
enable Modify enable password parameters
end Exit from configure mode
exit Exit from configure mode
hostname Set system's network name
interface Select an interface to configure
ip Global IP configuration subcommands
line Configure a terminal line
mac-address-table Configure the MAC address table
no Negate a command or set its defaults
service Modify use of network based services
spanning-tree Spanning Tree Subsystem
username Establish User Name Authentication
vlan Vlan commands
vtp Configure global VTP state
CoreSW(config)#interface ?
Ethernet IEEE 802.3
FastEthernet FastEthernet IEEE 802.3
GigabitEthernet GigabitEthernet IEEE 802.3z
Vlan Catalyst Vlans
range interface range command
CoreSW(config)#interface rang fa0/2-4
^
% Invalid input detected at '^' marker.
CoreSW(config)#interface rang fa0/2?
. <0-24>
CoreSW(config)#interface rang fa0/2 – 4 //使用rang进行 配置，更加便捷
CoreSW(config-if-range)#switchport mode access
CoreSW(config-if-range)#switchport access vlan 20
CoreSW(config-if-range)#interface rang fa0/5 - 6
CoreSW(config-if-range)#switchport mode access
CoreSW(config-if-range)#switch
CoreSW(config-if-range)#switchport a
CoreSW(config-if-range)#switchport access vlan 30
CoreSW(config-if-range)#show vlan
^
% Invalid input detected at '^' marker.
CoreSW(config-if-range)#exit
CoreSW(config)#exit
%SYS-5-CONFIG_I: Configured from console by console
CoreSW#show vlan
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Fa0/8, Fa0/9, Fa0/10, Fa0/11
Fa0/12, Fa0/13, Fa0/14, Fa0/15
Fa0/16, Fa0/17, Fa0/18, Fa0/19
Fa0/20, Fa0/21, Fa0/22, Fa0/23
Fa0/24, Gig1/1, Gig1/2
10 Math active Fa0/1, Fa0/7
20 Chinese active Fa0/2, Fa0/3, Fa0/4
30 Other active Fa0/5, Fa0/6
//上面显示了当前配置的vlan和对应接口下所有的信息
1002 fddi-default active
1003 token-ring-default active
1004 fddinet-default active
1005 trnet-default active
VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
1 enet 100001 1500 - - - - - 0 0
10 enet 100010 1500 - - - - - 0 0
20 enet 100020 1500 - - - - - 0 0
30 enet 100030 1500 - - - - - 0 0
CoreSW#
CoreSW#show vlan brief
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Fa0/8, Fa0/9, Fa0/10, Fa0/11
Fa0/12, Fa0/13, Fa0/14, Fa0/15
Fa0/16, Fa0/17, Fa0/18, Fa0/19
Fa0/20, Fa0/21, Fa0/22, Fa0/23
Fa0/24, Gig1/1, Gig1/2
10 Math active Fa0/1, Fa0/7
20 Chinese active Fa0/2, Fa0/3, Fa0/4
30 Other active Fa0/5, Fa0/6
1002 fddi-default active
1003 token-ring-default active
1004 fddinet-default active
1005 trnet-default active
CoreSW#
CoreSW#show vlan id 10
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
10 Math active Fa0/1, Fa0/7
VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
10 enet 100010 1500 - - - - - 0 0
CoreSW#show vlan id 30
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
30 Other active Fa0/5, Fa0/6
VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
30 enet 100030 1500 - - - - - 0 0
CoreSW#vlan name Match
^
% Invalid input detected at '^' marker.
CoreSW#show vlan Math
^
% Invalid input detected at '^' marker.
CoreSW#
CoreSW#show vlan Math
^
% Invalid input detected at '^' marker.
CoreSW#show vlan name Math
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
10 Math active Fa0/1, Fa0/7
VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
10 enet 100010 1500 - - - - - 0 0
CoreSW#show vlan name Other
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
30 Other active Fa0/5, Fa0/6
VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
30 enet 100030 1500 - - - - - 0 0
CoreSW#show vlan name Chinese
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
20 Chinese active Fa0/2, Fa0/3, Fa0/4
VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
20 enet 100020 1500 - - - - - 0 0
CoreSW#show vlan
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Fa0/8, Fa0/9, Fa0/10, Fa0/11
Fa0/12, Fa0/13, Fa0/14, Fa0/15
Fa0/16, Fa0/17, Fa0/18, Fa0/19
Fa0/20, Fa0/21, Fa0/22, Fa0/23
Fa0/24, Gig1/1, Gig1/2
10 Math active Fa0/1, Fa0/7
20 Chinese active Fa0/2, Fa0/3, Fa0/4
30 Other active Fa0/5, Fa0/6
1002 fddi-default active
1003 token-ring-default active
1004 fddinet-default active
1005 trnet-default active
VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
1 enet 100001 1500 - - - - - 0 0
10 enet 100010 1500 - - - - - 0 0
20 enet 100020 1500 - - - - - 0 0
30 enet 100030 1500 - - - - - 0 0
1002 enet 101002 1500 - - - - - 0 0
1003 enet 101003 1500 - - - - - 0 0
1004 enet 101004 1500 - - - - - 0 0
1005 enet 101005 1500 - - - - - 0 0
CoreSW#
CoreSW#show vlan
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Fa0/8, Fa0/9, Fa0/10, Fa0/11
Fa0/12, Fa0/13, Fa0/14, Fa0/15
Fa0/16, Fa0/17, Fa0/18, Fa0/19
Fa0/20, Fa0/21, Fa0/22, Fa0/23
Fa0/24, Gig1/1, Gig1/2
10 Math active Fa0/1, Fa0/7
20 Chinese active Fa0/2, Fa0/3, Fa0/4
30 Other active Fa0/5, Fa0/6
1002 fddi-default active
1003 token-ring-default active
1004 fddinet-default active
1005 trnet-default active
VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
1 enet 100001 1500 - - - - - 0 0
10 enet 100010 1500 - - - - - 0 0
20 enet 100020 1500 - - - - - 0 0
30 enet 100030 1500 - - - - - 0 0
CoreSW#interface fa0/1
^
% Invalid input detected at '^' marker.
CoreSW#show vlan
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Fa0/8, Fa0/9, Fa0/10, Fa0/11
Fa0/12, Fa0/13, Fa0/14, Fa0/15
Fa0/16, Fa0/17, Fa0/18, Fa0/19
Fa0/20, Fa0/21, Fa0/22, Fa0/23
Fa0/24, Gig1/1, Gig1/2
10 Math active Fa0/1, Fa0/7
20 Chinese active Fa0/2, Fa0/3, Fa0/4
30 Other active Fa0/5, Fa0/6
1002 fddi-default active
1003 token-ring-default active
1004 fddinet-default active
1005 trnet-default active
VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
1 enet 100001 1500 - - - - - 0 0
10 enet 100010 1500 - - - - - 0 0
20 enet 100020 1500 - - - - - 0 0
30 enet 100030 1500 - - - - - 0 0
1002 enet 101002 1500 - - - - - 0 0
1003 enet 101003 1500 - - - - - 0 0
1004 enet 101004 1500 - - - - - 0 0
1005 enet 101005 1500 - - - - - 0 0
CoreSW#?
Exec commands:
<1-99> Session number to resume
clear Reset functions
clock Manage the system clock
configure Enter configuration mode
connect Open a terminal connection
copy Copy from one file to another
debug Debugging functions (see also 'undebug')
delete Delete a file
dir List files on a filesystem
disable Turn off privileged commands
disconnect Disconnect an existing network connection
enable Turn on privileged commands
erase Erase a filesystem
exit Exit from the EXEC
logout Exit from the EXEC
more Display the contents of a file
no Disable debugging informations
ping Send echo messages
reload Halt and perform a cold restart
resume Resume an active network connection
setup Run the SETUP command facility
show Show running system information
telnet Open a telnet connection
terminal Set terminal line parameters
traceroute Trace route to destination
undebug Disable debugging functions (see also 'debug')
vlan Configure VLAN parameters
write Write running configuration to memory, network, or terminal
CoreSW#confi t
Enter configuration commands, one per line. End with CNTL/Z.
CoreSW(config)#?
Configure commands:
banner Define a login banner
boot Boot Commands
cdp Global CDP configuration subcommands
clock Configure time-of-day clock
do To run exec commands in config mode
enable Modify enable password parameters
end Exit from configure mode
exit Exit from configure mode
hostname Set system's network name
interface Select an interface to configure
ip Global IP configuration subcommands
line Configure a terminal line
mac-address-table Configure the MAC address table
no Negate a command or set its defaults
service Modify use of network based services
spanning-tree Spanning Tree Subsystem
username Establish User Name Authentication
vlan Vlan commands
vtp Configure global VTP state
CoreSW(config)#show vlan
^
% Invalid input detected at '^' marker.
CoreSW(config)#show vlan
^
% Invalid input detected at '^' marker.
//以下是删除某个接口对应的vlan和删除整个id的vlan
CoreSW(config)#interface fa0/1
CoreSW(config-if)#no swithport access vlan 10
^
% Invalid input detected at '^' marker.
CoreSW(config-if)#no switchport access vlan 10
CoreSW(config-if)#exit
CoreSW(config)#exit
%SYS-5-CONFIG_I: Configured from console by console
CoreSW#show vlan
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Fa0/1, Fa0/8, Fa0/9, Fa0/10
Fa0/11, Fa0/12, Fa0/13, Fa0/14
Fa0/15, Fa0/16, Fa0/17, Fa0/18
Fa0/19, Fa0/20, Fa0/21, Fa0/22
Fa0/23, Fa0/24, Gig1/1, Gig1/2
10 Math active Fa0/7
20 Chinese active Fa0/2, Fa0/3, Fa0/4
30 Other active Fa0/5, Fa0/6
1002 fddi-default active
1003 token-ring-default active
1004 fddinet-default active
1005 trnet-default active
VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
1 enet 100001 1500 - - - - - 0 0
10 enet 100010 1500 - - - - - 0 0
20 enet 100020 1500 - - - - - 0 0
30 enet 100030 1500 - - - - - 0 0
1002 enet 101002 1500 - - - - - 0 0
1003 enet 101003 1500 - - - - - 0 0
1004 enet 101004 1500 - - - - - 0 0
1005 enet 101005 1500 - - - - - 0 0
CoreSW#config t
Enter configuration commands, one per line. End with CNTL/Z.
CoreSW(config)#?
Configure commands:
banner Define a login banner
boot Boot Commands
cdp Global CDP configuration subcommands
clock Configure time-of-day clock
do To run exec commands in config mode
enable Modify enable password parameters
end Exit from configure mode
exit Exit from configure mode
hostname Set system's network name
interface Select an interface to configure
ip Global IP configuration subcommands
line Configure a terminal line
mac-address-table Configure the MAC address table
no Negate a command or set its defaults
service Modify use of network based services
spanning-tree Spanning Tree Subsystem
username Establish User Name Authentication
vlan Vlan commands
vtp Configure global VTP state
CoreSW(config)#no vlan 20
CoreSW(config)#exit
%SYS-5-CONFIG_I: Configured from console by console
CoreSW#show vlan
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Fa0/1, Fa0/8, Fa0/9, Fa0/10
Fa0/11, Fa0/12, Fa0/13, Fa0/14
Fa0/15, Fa0/16, Fa0/17, Fa0/18
Fa0/19, Fa0/20, Fa0/21, Fa0/22
Fa0/23, Fa0/24, Gig1/1, Gig1/2
10 Math active Fa0/7
30 Other active Fa0/5, Fa0/6
1002 fddi-default active
1003 token-ring-default active
1004 fddinet-default active
1005 trnet-default active
VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
1 enet 100001 1500 - - - - - 0 0
10 enet 100010 1500 - - - - - 0 0
30 enet 100030 1500 - - - - - 0 0
1002 enet 101002 1500 - - - - - 0 0
1003 enet 101003 1500 - - - - - 0 0
1004 enet 101004 1500 - - - - - 0 0
1005 enet 101005 1500 - - - - - 0 0
