BCM5892启动信息

DDR initialization...
Reset DDR Controller
Configuring DDR

mclk = 133, auto refresh = 0x3df

DDR DLL locked...!!!

Doing DDR data eye training sequence ....

DDR data eye training sequence passed...!!!

Please press ENTER to download menu...

Switching to Open mode...Done.

Micron NAND 512MiB 3,3V 8-bit device ID 0xdc

supported Mciron NAND 4G08 device.

U-Boot loading from NAND


U-Boot 1.1.4 (May 18 2012 - 09:47:20)

U-Boot code: 43A00000 -> 43A2E200 BSS: -> 43A57150
Manufacturer ID: 0000
Unknown Manufacturer ID: 0000
Flash: 0 kB
mem start 43900000 end 439fffff [Fixme]
glb data 43a51f54
NAND: 8bit WIDTH UMC_R_umc_addr_match_MEMADDR=380d30,
UMC : Address match = 0x380d30
device code=0xDC
NAND_4GB_8BIT supported
NAND ids=0x9590dc2c, nand_maf_id=0x2c, nand_dev_id=0xdc
malloc sbrk_size 536 pagesz 4096
sbrk old 43900000 new 43900218 increment 536
sbrk alloc 43900000 536
sbrk old 43900218 new 43901000 increment 3560
sbrk alloc 43900218 3560
malloc sbrk_size 12288 pagesz 4096
sbrk old 43901000 new 43904000 increment 12288
sbrk alloc 43901000 12288
BBT found at 0x3ff
512 MiB
malloc sbrk_size 135168 pagesz 4096
sbrk old 43904000 new 43925000 increment 135168
sbrk alloc 43904000 135168
malloc sbrk_size 4096 pagesz 4096
sbrk old 43925000 new 43926000 increment 4096
sbrk alloc 43925000 4096
sbrk old 43926000 new 43926000 increment 0
sbrk alloc 43926000 0
In: serial
Out: serial
Err: serial
Hit any key to stop autoboot: 0

NAND read: device 0 offset 0x140000, size 0x200000
............... 2097152 bytes read: OK
Boot reached stage 1
## Booting image at 40d08000 ...
Boot reached stage 2
Boot reached stage 3
   Image Name: Linux-2.6.32.9
   Image Type: ARM Linux Kernel Image (uncompressed)
   Data Size: 1713884 Bytes = 1.6 MB
   Load Address: 40008000
   Entry Point: 40008000
Boot reached stage 4
Boot reached stage 5
Boot reached stage 6
OK
Boot reached stage 7
Boot reached stage 8
Boot reached stage 14
Boot reached stage 15

Starting kernel ...

Uncompressing Linux............................................................................................................... done, booting the kernel.
[ 0.000000] Linux version 2.6.32.9 ([e-mail]) (gcc version 4.2.3) #72 PREEMPT Mon Mar 19 01:37:54 EDT 2012
[ 0.000000] CPU: ARMv6-compatible processor [4117b365] revision 5 (ARMv6TEJ), cr=00c5387d
[ 0.000000] CPU: VIPT aliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine: Broadcom BCM5892 Chip
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: console=ttyS1,115200n8 mem=64M root=/dev/nfs rw ip=172.16.17.201:172.16.17.156:172.16.17.1:255.255.255.0::eth0:off nfsroot=172.16.17.156:/home/newpos/rootfs
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Memory: 64MB = 64MB total
[ 0.000000] Memory: 61212KB available (3216K code, 313K data, 108K init, 0K highmem)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:96
[ 0.000000] timer2: periodic 60000
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] console [ttyS1] enabled
[ 0.020000] Calibrating delay loop... 398.95 BogoMIPS (lpj=1994752)
[ 0.230000] Mount-cache hash table entries: 512
[ 0.230000] CPU: Testing write buffer coherency: ok
[ 0.240000] NET: Registered protocol family 16
[ 0.260000] SDIO0 init
[ 0.260000] SDM0 reset skip
[ 0.260000] SDIO1 init
[ 0.260000] SDM1 reset skip
[ 0.270000] call_secure_api_internal: 33
[ 0.270000] bcm5892_bootmemheap_calc_mmdma: Reserving memory 2097152 bytes for MMDMA
[ 0.280000] PL080-DMA: Module loaded.
[ 0.290000] bio: create slab <bio-0> at 0
[ 0.290000] SCSI subsystem initialized
[ 0.300000] usbcore: registered new interface driver usbfs
[ 0.310000] usbcore: registered new interface driver hub
[ 0.310000] usbcore: registered new device driver usb
[ 0.320000] Switching to clocksource hw_source_timer
[ 0.320000] NET: Registered protocol family 2
[ 0.330000] Switched to NOHz mode on CPU #0
[ 0.330000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.330000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.330000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.330000] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.330000] TCP reno registered
[ 0.330000] NET: Registered protocol family 1
[ 0.330000] RPC: Registered udp transport module.
[ 0.330000] RPC: Registered tcp transport module.
[ 0.330000] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.330000] bootmemheap_init: Error - bootmemheap_setup() not called
[ 0.390000] JFFS2 version 2.2. (NAND) (SUMMARY) 2001-2006 Red Hat, Inc.
[ 0.390000] yaffs Mar 5 2012 06:35:34 Installing.
[ 0.390000] msgmni has been set to 119
[ 0.390000] io scheduler noop registered (default)
[ 0.810000] Audio Mixer Driver: 1.0
[ 0.810000] Broadcom GPIO Driver: 1.00
[ 0.810000] Serial: AMBA 5892 BCM5892UART UART driver
[ 0.810000] ttyS0 at MMIO 0xd0000 (irq = 70) is a AMBA/BCM5892UART
[ 0.810000] ttyS1 at MMIO 0xd1000 (irq = 71) is a AMBA/BCM5892UART
[ 0.810000] ttyS2 at MMIO 0xd2000 (irq = 72) is a AMBA/BCM5892UART
[ 0.810000] ttyS3 at MMIO 0xd3000 (irq = 73) is a AMBA/BCM5892UART
[ 0.810000] brd: module loaded
[ 0.810000] loop: module loaded
[ 0.810000] NAND device ID: 9590dc2c
[ 0.810000] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xdc (Micron NAND 512MiB 3,3V 8-bit) options=0x101
[ 0.810000] Bad block table not found for chip 0
[ 0.950000] No space left to write bad block table
[ 0.950000] bcm5892-mac: MAC addr: 00:01:02:03:04:05
[ 0.950000] bcm5892-mac: driver trace at c038fa20
[ 0.950000] Initializing USB Mass Storage driver...
[ 1.030000] usbcore: registered new interface driver usb-storage
[ 1.030000] USB Mass Storage support registered.
[ 1.030000] mice: PS/2 mouse device common for all mice
[ 1.030000] Driver for 1-wire Dallas network protocol.
[ 1.030000] sdhci: Secure Digital Host Controller Interface driver
[ 1.030000] sdhci: Copyright(c) Pierre Ossman
[ 1.030000] sdhci: modified by Broadcom for SDIO Wireless purposes
[ 1.030000] mmc0: Unknown controller version (2). You may experience problems.
[ 1.080000] mmc0: SDHCI controller on BCM-SDIO [bcm-sdio.0] using ADMA
[ 1.080000] mmc1: Unknown controller version (2). You may experience problems.
[ 1.080000] mmc1: SDHCI controller on BCM-SDIO [bcm-sdio.1] using ADMA
[ 1.080000] SDIO: sdhci_platform_done
[ 1.080000] usbcore: registered new interface driver usbhid
[ 1.080000] usbhid: v2.6:USB HID core driver
[ 1.080000] TCP cubic registered
[ 1.080000] NET: Registered protocol family 17
[ 1.080000] NET: Registered protocol family 15
[ 1.080000] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 1.650000] bcm5892mac_open: val: 00000008, val1 fffffff8
[ 1.650000] sd:in the open routine
[ 1.650000] Before mdiobus_register: c39c3ac0, c39c3af4
[ 1.650000] bcm5892-mac-mdio: probed
[ 1.650000] After mdiobus_register: c39c3ac0, c39c3af4
[ 3.750000] PHY eth0: link status:0 Autoneg 1 10base-HD
[ 3.750000] IP-Config: Complete:
[ 3.750000] device=eth0, addr=172.16.17.201, mask=255.255.255.0, gw=172.16.17.1,
[ 3.750000] host=172.16.17.201, domain=, nis-domain=(none),
[ 3.750000] bootserver=172.16.17.156, rootserver=172.16.17.156, rootpath=
[ 3.750000] Looking up port of RPC 100003/2 on 172.16.17.156
[ 4.780000] PHY eth0: link status:1 Autoneg 1 100base-FD
[ 4.780000] FULL Duplex
[ 4.780000] CONTEXT eth0: link available: 100base-FD
[ 4.850000] Looking up port of RPC 100005/1 on 172.16.17.156
[ 4.850000] VFS: Mounted root (nfs filesystem) on device 0:10.
[ 4.850000] Freeing init memory: 108K
[ 5.550000] sunrpc: module is already loaded
[ 5.600000] lockd: module is already loaded
[ 5.720000] nfs: module is already loaded
[ 5.720000] bcm589x_pmb: module license 'unspecified' taints kernel.
[ 5.720000] Disabling lock debugging due to kernel taint
[ 5.850000] bcm5892-rtc bcm5892-rtc: rtc core: registered bcm5892-rtc as rtc0
[ 5.850000] BCM5892 Real Time Clock driver.
[ 5.850000] BCM5892 PM: Initializing Power Management for BCM5892...
entering /etc/rc.d/S010fs ...
leaving /etc/rc.d/S010fs ...
entering /etc/rc.d/S010network ...
setting up lo interface
/nvdata/etc directory already present
sending dhcp request
leaving /etc/rc.d/S010network ...
entering /etc/rc.d/S030proc-config ...
leaving /etc/rc.d/S030proc-config ...
entering /etc/rc.d/S050log ...
leaving /etc/rc.d/S050log ...
entering /etc/rc.d/S090apps ...
cp: cannot stat '/etc/avatar.yuv': No such file or directory
cp: cannot stat '/etc/cameraoff.yuv': No such file or directory
leaving /etc/rc.d/S090apps ...
entering /etc/rc.d/S099local ...
Module Size Used by Tainted: P
bcm589x_dmu 1288 0
bcm589x_pm 4322 0 [permanent]
bcm589x_rtc 3397 0
bcm589x_pmb 3422 1 bcm589x_rtc
leaving /etc/rc.d/S099local ...

Please press Enter to activate this console.
+---------------------------------------------------------------------------+
| Authorized Use Only. |
| Activity on this system is subject to monitoring and logging. |
+---------------------------------------------------------------------------+
172.16.17.18 # ls
7 lib share
bin mnt sys
dev nvdata tmp
devicetable.txt pre-udev-devicetable.txt usr
etc proc var
home sbin webroot
172.16.17.18 #