void disable_watch_dog(void)
{
WTCON = 0; // 关闭WATCHDOG很简单，往这个寄存器写0即可
}
#define S3C2440_MPLL_200MHZ ((0x5c<<12)|(0x01<<4)|(0x02))
/*
* 对于MPLLCON寄存器，[19:12]为MDIV，[9:4]为PDIV，[1:0]为SDIV
* 有如下计算公式：
* S3C2440: MPLL(FCLK) = (2 * m * Fin)/(p * 2^s)
* 其中: m = MDIV + 8, p = PDIV + 2, s = SDIV
* 对于本开发板，Fin = 12MHz
* 设置CLKDIVN，令分频比为：FCLK:HCLK:PCLK=1:2:4，
* FCLK=200MHz,HCLK=100MHz,PCLK=50MHz
*/
void clock_init(void)
{
CLKDIVN = 0x03; // FCLK:HCLK:PCLK=1:2:4, HDIVN=1,PDIVN=1
/* 如果HDIVN非0，CPU的总线模式应该从“fast bus mode”变为“asynchronous bus mode” */
__asm{
mrc p15, 0, r1, c1, c0, 0 /* 读出控制寄存器 */
orr r1, r1, #0xc0000000 /* 设置为“asynchronous bus mode” */
mcr p15, 0, r1, c1, c0, 0 /* 写入控制寄存器 */
}
MPLLCON = S3C2440_MPLL_200MHZ; /* 现在，FCLK=200MHz,HCLK=100MHz,PCLK=50MHz */
}
/*
* 设置存储控制器以使用SDRAM
*/
void memsetup(void)
{
volatile unsigned long *p = (volatile unsigned long *)MEM_CTL_BASE;
/* 这个函数之所以这样赋值，而不是像前面的实验(比如mmu实验)那样将配置值
* 写在数组中，是因为要生成”位置无关的代码”，使得这个函数可以在被复制到
* SDRAM之前就可以在steppingstone中运行
*/
/* 存储控制器13个寄存器的值 */
p[0] = 0x22011110; //BWSCON
p[1] = 0x00000700; //BANKCON0
p[2] = 0x00000700; //BANKCON1
p[3] = 0x00000700; //BANKCON2
p[4] = 0x00000700; //BANKCON3
p[5] = 0x00000700; //BANKCON4
p[6] = 0x00000700; //BANKCON5
p[7] = 0x00018005; //BANKCON6
p[8] = 0x00018005; //BANKCON7
/* REFRESH,
* HCLK=12MHz: 0x008C07A3,
* HCLK=100MHz: 0x008C04F4
*/
p[9] = 0x008C04F4;
p[10] = 0x000000B1; //BANKSIZE
p[11] = 0x00000030; //MRSRB6
p[12] = 0x00000030; //MRSRB7
}
$$$$$$$$$$$$$$$$ serial.h $$$$$$$$$$$$$$$
void uart0_init(void);
void putc(unsigned char c);
unsigned char getc(void);
int isDigit(unsigned char c);
int isLetter(unsigned char c);
**************** serial.c ****************
#include "s3c24xx.h"
#include "serial.h"
#define TXD0READY (1<<2)
#define RXD0READY (1)
#define PCLK 50000000 // init.c中的clock_init函数设置PCLK为50MHz
#define UART_CLK PCLK // UART0的时钟源设为PCLK
#define UART_BAUD_RATE 115200 // 波特率
#define UART_BRD ((UART_CLK / (UART_BAUD_RATE * 16)) - 1)
/*
* 初始化UART0
* 115200,8N1,无流控
*/
void uart0_init(void)
{
GPHCON |= 0xa0; // GPH2,GPH3用作TXD0,RXD0
GPHUP = 0x0c; // GPH2,GPH3内部上拉
ULCON0 = 0x03; // 8N1(8个数据位，无较验，1个停止位)
UCON0 = 0x05; // 查询方式，UART时钟源为PCLK
UFCON0 = 0x00; // 不使用FIFO
UMCON0 = 0x00; // 不使用流控
UBRDIV0 = UART_BRD; // 波特率为115200
}
/*
* 发送一个字符
*/
void putc(unsigned char c)
{
/* 等待，直到发送缓冲区中的数据已经全部发送出去 */
while (!(UTRSTAT0 & TXD0READY));
/* 向UTXH0寄存器中写入数据，UART即自动将它发送出去 */
UTXH0 = c;
}
/*
* 接收字符
*/
unsigned char getc(void)
{
/* 等待，直到接收缓冲区中的有数据 */
while (!(UTRSTAT0 & RXD0READY));
/* 直接读取URXH0寄存器，即可获得接收到的数据 */
return URXH0;
}
/*
* 判断一个字符是否数字
*/
int isDigit(unsigned char c)
{
if (c >= '0' && c <= '9')
return 1;
else
return 0;
}
/*
* 判断一个字符是否英文字母
*/
int isLetter(unsigned char c)
{
if (c >= 'a' && c <= 'z')
return 1;
else if (c >= 'A' && c <= 'Z')
return 1;
else
return 0;
}
&&&&&&&&&&&&& main.c &&&&&&&&&&&&&&&&&&
#include "serial.h"
int Main()
{
unsigned char c;
uart0_init(); // 波特率115200，8N1(8个数据位，无校验位，1个停止位)
while(1)
{
// 从串口接收数据后，判断其是否数字或子母，若是则加2后输出
c = getc(); //接收数据
if (isDigit(c) || isLetter(c)) //判断
putc(c+2); //加2后输出
}
return 0;
}
%%%%%%%%%%%%% s3c2440 %%%%%%%%%%%%%%%%%%%
/* WOTCH DOG register */
#define WTCON (*(volatile unsigned long *)0x53000000)
/* SDRAM regisers */
#define MEM_CTL_BASE 0x48000000
#define SDRAM_BASE 0x30000000
/* NAND Flash registers */
#define NFCONF (*(volatile unsigned int *)0x4e000000)
#define NFCMD (*(volatile unsigned char *)0x4e000004)
#define NFADDR (*(volatile unsigned char *)0x4e000008)
#define NFDATA (*(volatile unsigned char *)0x4e00000c)
#define NFSTAT (*(volatile unsigned char *)0x4e000010)
/*GPIO registers*/
#define GPBCON (*(volatile unsigned long *)0x56000010)
#define GPBDAT (*(volatile unsigned long *)0x56000014)
#define GPFCON (*(volatile unsigned long *)0x56000050)
#define GPFDAT (*(volatile unsigned long *)0x56000054)
#define GPFUP (*(volatile unsigned long *)0x56000058)
#define GPGCON (*(volatile unsigned long *)0x56000060)
#define GPGDAT (*(volatile unsigned long *)0x56000064)
#define GPGUP (*(volatile unsigned long *)0x56000068)
#define GPHCON (*(volatile unsigned long *)0x56000070)
#define GPHDAT (*(volatile unsigned long *)0x56000074)
#define GPHUP (*(volatile unsigned long *)0x56000078)
/*UART registers*/
#define ULCON0 (*(volatile unsigned long *)0x50000000)
#define UCON0 (*(volatile unsigned long *)0x50000004)
#define UFCON0 (*(volatile unsigned long *)0x50000008)
#define UMCON0 (*(volatile unsigned long *)0x5000000c)
#define UTRSTAT0 (*(volatile unsigned long *)0x50000010)
#define UTXH0 (*(volatile unsigned char *)0x50000020)
#define URXH0 (*(volatile unsigned char *)0x50000024)
#define UBRDIV0 (*(volatile unsigned long *)0x50000028)
/*interrupt registes*/
#define SRCPND (*(volatile unsigned long *)0x4A000000)
#define INTMOD (*(volatile unsigned long *)0x4A000004)
#define INTMSK (*(volatile unsigned long *)0x4A000008)
#define PRIORITY (*(volatile unsigned long *)0x4A00000c)
#define INTPND (*(volatile unsigned long *)0x4A000010)
#define INTOFFSET (*(volatile unsigned long *)0x4A000014)
#define SUBSRCPND (*(volatile unsigned long *)0x4A000018)
#define INTSUBMSK (*(volatile unsigned long *)0x4A00001c)
/*external interrupt registers*/
#define EINTMASK (*(volatile unsigned long *)0x560000a4)
#define EINTPEND (*(volatile unsigned long *)0x560000a8)
/*clock registers*/
#define LOCKTIME (*(volatile unsigned long *)0x4c000000)
#define MPLLCON (*(volatile unsigned long *)0x4c000004)
#define UPLLCON (*(volatile unsigned long *)0x4c000008)
#define CLKCON (*(volatile unsigned long *)0x4c00000c)
#define CLKSLOW (*(volatile unsigned long *)0x4c000010)
#define CLKDIVN (*(volatile unsigned long *)0x4c000014)
/*PWM & Timer registers*/
#define TCFG0 (*(volatile unsigned long *)0x51000000)
#define TCFG1 (*(volatile unsigned long *)0x51000004)
#define TCON (*(volatile unsigned long *)0x51000008)
#define TCNTB0 (*(volatile unsigned long *)0x5100000c)
#define TCMPB0 (*(volatile unsigned long *)0x51000010)
#define TCNTO0 (*(volatile unsigned long *)0x51000014)
#define GSTATUS1 (*(volatile unsigned long *)0x560000B0)
