Solaris平台下的硬盘具体增设方法大致如下:
1. 关闭系统,进入PROM状态 # init 0 ok (PROM状态提示)
2. 在PROM状态提示符下确认当前系统所连接的SCSI设备状况 ok probe-scsi 或 ok probe-scsi-all
这时,系统将显示所能识别的SCSI设备极其设备号(Target ID).如果新连接的硬 盘之信息没有出现时,请按下述方法进行确认.
1) 检查设备号是否重复?
Target-ID SunOS 4.xSolaris 2.x
2) 内藏硬盘
1 硬盘 通常与SunOS 4.x一致.
2 硬盘 当ID不重复时, 4,5也
0 硬盘 可以用于硬盘.
4 磁带
5 磁带
6 CD-ROM CD-ROM
2) 检查电缆,插口,终端器等物理连接是否无误?
3) SCSI电缆的总长度是否在6米以内? |
3. 重新起动系统 ok boot -r
注意,只有加入"-r"选项时, 系统在起动时才给所识别了的设备(包括SCSI设备) 生成相应的设备文件.
4. 对新增设的硬盘进行盘区划分 进入系统状态后,执行format命令,对新增设的硬盘进行盘区划分.
执行例
# format
Searching for disks...done |
AVAILABLE DISK SELECTIONS:
0. c0t3d0
/sbus@1,f8000000/esp@0,800000/sd@3,0
Specify disk (enter its number): 0 <-- 选择硬盘 selecting c0t3d0 [disk formatted] formAT MENU: disk select a disk type select (define) a disk type partition select (define) a partition table current describe the current disk format format and analyze the disk repair repair a defective sector show translate a disk address label write label to the disk analyze surface analysis defect defect list management backup search for backup labels verify read and display labels save save new disk/partition definitions volname set 8-character volume name quit format> partition <-- 键入partition(或par)进入分区状态 PARTITION MENU: 0 change `0' partition 1 change `1' partition 2 change `2' partition 3 change `3' partition 4 change `4' partition 5 change `5' partition 6 change `6' partition 7 change `7' partition select select a predefined table modify modify a predefined partition table name name the current table print display the current table label write partition map and label to the disk quit partition> modify <-- 键入modify(或mod),修改当前分区表. Select partitioning base: 0. Current partition table (original) 1. All Free Hog Choose base (enter number) [0]? 0 <-- 选择当前分区表. Part Tag Flag Cylinders Size Blocks 0 unassigned wm 0 17 15.90MB (18/0/0) 1 unassigned wm 18 88 62.71MB (71/0/0) 2 unassigned wm 0 742 656.29MB (743/0/0) 3 unassigned wm 89 121 29.15MB (33/0/0) 4 unassigned wm 0 0 (0/0/0) 5 unassigned wm 122 230 96.28MB (109/0/0) 6 unassigned wm 231 555 287.07MB (325/0/0) 7 unassigned wm 556 742 165.18MB (187/0/0) Do you wish to continue creating a new partition table based on above table[yes]? y <-- 键入y,以当前分区表为基准分区. Free Hog partition[6]? 7 <-- 选择适当的浮动区.(注1) Enter size of partition '0' [32562b, 18c, 15.90mb]: 16mb <-- 指定容量 Enter size of partition '1' [128439b, 71c, 62.71mb]: 62.7mb (注2) Enter size of partition '3' [59697b, 33c, 29.15mb]: 29mb Enter size of partition '4' [0b, 0c, 0.00mb]: 0 Enter size of partition '5' [197181b, 109c, 96.28mb]: 96mb Enter size of partition '6' [587925b, 325c, 287.07mb]: 287mb Part Tag Flag Cylinders Size Blocks 0 unassigned wm 0 18 16.78MB (19/0/0) 1 unassigned wm 19 89 62.71MB (71/0/0) 2 unassigned wm 0 742 656.29MB (743/0/0) 3 unassigned wm 90 122 29.15MB (33/0/0) 4 unassigned wm 0 0 (0/0/0) 5 unassigned wm 123 231 96.28MB (109/0/0) 6 unassigned wm 232 556 287.07MB (325/0/0) 7 unassigned wm 557 742 164.29MB (186/0/0) Okay to make this the current partition table[yes]? y <-- 确认后键入y. Enter table name (remember quotes): new_table <-- 键入适当的名称. partition> label <-- 键入label(或lab),设定系统标识. ok to label disk? y <-- 键入y partition> q <-- 键入q退出分区状态. format> q <-- 键入q退出format
(注1) 当改变其他分区尺寸时, 浮动区(Free Hog)用于在容量范围内进行自动调 节.
(注2) 分区容量的具体指定方法为:
容量数值后面加"b": 指定块数.
容量数值后面加"c": 指定柱面数.
容量数值后面加"mb": 指定MB数.
建议采用"mb",以兆字节为单位指定分区容量.
5. 生成新的文件系统用newfs命令将所划分的分区生成为新的文件系统.
#/usr/sbin/newfs /dev/rdsk/c0t1d0s7 (CR)
如果在上述过程中将整个硬盘指定为一个分区,可执行下述命令.
# /usr/sbin/newfs /dev/rdsk/c0t1d0s2 (CR)
6. 检查新生成的文件系统 用fsck命令检查新生成的文件系统是否正确.
# /usr/sbin/fsck /dev/rdsk/c0t1d0s7 (CR)
如果在上述过程中将整个硬盘指定为一个分区,可执行下述命令.
# /usr/sbin/fsck /dev/rdsk/c0t1d0s2 (CR)
7. 安装新生成的文件系统 建立安装用目录后用mount命令进行安装.
例如,要将第7分区之文件系统用于home1时,可执行下述命令.
# mkdir /home1 (CR)
# mount /dev/dsk/c0t1d0s7 /home1 (CR)
|
8. 确认安装结果 用df命令确认安装结果.
9. 自动安装新设文件系统 为在系统起动时自动安装新设文件系统,修改/etc/vfstab文件.
# vi /etc/vfstab (CR)
#device device mount FS fsck mount mount
#to mount to fsck point type pass at boot options
#
:
/dev/dsk/c0t3d0s7 /dev/rdsk/c0t3d0s7 /home1 ufs 6 yes - |
10. 重新起动系统
