maui-soho-01 (1600)
maui-soho-01#show running-config
Building configuration...
Current configuration : 1656 bytes
!
version 12.1
no service single-slot-reload-enable
service timestamps debug datetime msec
service timestamps log datetime msec
!
hostname maui-soho-01
!
logging rate-limit console 10 except errors
aaa new-model
aaa authentication login default local
aaa authentication login NO_AUTHEN none
aaa authentication ppp default local
!--- basic AAA configuration for PPP calls
enable secret 5
!
username admin password
username maui-nas-05 password cisco
!--- username for remote router (maui-nas-05) and shared secret
!--- (used for CHAP authentication)
!--- Shared secret must be the same on both sides.
ip subnet-zero
!
isdn switch-type basic-ni
!
interface Loopback0
ip address 172.17.1.1 255.255.255.0
!--- The loopback address will be used by OSPF for the router ID.
!
interface Ethernet0
ip address 172.16.1.1 255.255.255.0
!
interface Serial0
no ip address
shutdown
no fair-queue
!
interface BRI0
!--- BRI interface used for DDR dialout
ip address 172.20.10.2 255.255.255.0
!--- IP address
!--- The remote address is in the same subnet.
encapsulation ppp
ip ospf demand-circuit
!--- This forces OSPF to keep the routing table intact when the DDR link
!--- is down. This should only be configured on one router for a
!--- point-to-point circuit.
dialer idle-timeout 900
!--- Idle timeout is set to 900 seconds (15 minutes).
!--- The link will be disconnected if there is no interesting traffic
!--- for 900 secs.
dialer map ip 172.20.10.1 name maui-nas-05 broadcast 5551111
dialer map ip 172.20.10.1 name maui-nas-05 broadcast 5551112
!--- dialer map statements for the remote router
!--- The name must match the one used by the remote router to identify
!--- itself. The broadcast keyword is required to send broadcast traffic
!--- over the link(for OSPF). The two different phone numbers correspond
!--- to the b-channels of the remote side. The multiple statements allow
!--- the router to dial the second number if the first number is busy.
dialer load-threshold 80 outbound
!--- This set the load level for traffic at which additional connections
!--- will be added to the Multilink PPP bundle.!--- Load level values range from 1 (unloaded) to 255 (fully loaded).
!--- The threshold in this case is 80/255 = 32%.
dialer-group 1
!--- apply interesting traffic definition from dialer-list 1
isdn switch-type basic-ni
isdn spid1 51255522220101 5552222
isdn spid2 51255522230101 5552223
ppp authentication chap
!--- Use chap authentication.
ppp multilink
!--- Use multilink to bring up both BRI channels.
!
router ospf 5
log-adjacency-changes
network 172.16.1.0 0.0.0.255 area 0
network 172.17.1.0 0.0.0.255 area 0
network 172.20.10.0 0.0.0.255 area 0
!
ip classless
ip route 172.20.0.0 255.255.0.0 172.20.10.0
no ip http server
!
access-list 101 remark Define Interesting Traffic
access-list 101 deny ospf any any
!--- mark OSPF as uninteresting
!--- This will prevent OSPF hellos from keeping the link up.
access-list 101 permit ip any any
dialer-list 1 protocol ip list 101
!--- Interesting traffic is defined by access-list 101.
!--- This is applied to BRI0 using dialer-group 1.
!
line con 0
exec-timeout 0 0
login authentication NO_AUTHEN
transport input none
line vty 0 4
!
endmaui-nas-05 (3640)
maui-nas-05#show running-config
Building configuration...
Current configuration:
!
version 12.1
service timestamps debug datetime msec
service timestamps log datetime msec
!
hostname maui-nas-05
!
aaa new-model
aaa authentication login default local
aaa authentication login NO_AUTHEN none
aaa authentication ppp default local
!--- basic AAA configuration for PPP calls
enable secret 5
!
username admin password 7
username maui-soho-01 password 7 cisco
!--- username for remote router (maui-soho-01) and shared secret
!--- (used for CHAP authentication)
!--- Shared secret must be the same on both sides.
ip subnet-zero
!
isdn switch-type basic-ni
!
interface Loopback0
ip address 172.22.1.1 255.255.255.0
!--- The loopback address is used by OSPF for the router ID.
!
interface Ethernet0/0
ip address 172.22.53.105 255.255.255.0
!
interface Ethernet0/1
no ip address
shutdown
!
interface BRI1/0
!--- BRI interface used to accept dialin
ip address 172.20.10.1 255.255.255.0
!--- IP address
!--- The remote address is in the same subnet.
encapsulation ppp
dialer idle-timeout 900
!--- Idle timeout is set to 900 seconds (15 minutes).
!--- Set this value to be equal to or higher than the idle-timeout on the
!--- client side. A higher idle-timeout permits the client side to
!--- determine when to bring down the link.
!
dialer map ip 172.20.10.2 name maui-soho-01 broadcast
!--- dialer map statement for the BRI interface of the remote router
!--- The name must be the one used by the remote router to identify
!--- itself. The broadcast keyword is required to send broadcast traffic
!--- over the link(for OSPF). Note: There is no phone number, as we are
!--- not configuring this side to dial. If you want this router to dial,
!--- add the remote side phone number to the dialer map statement
dialer-group 1
!--- apply interesting traffic definition from dialer-list 1
isdn switch-type basic-ni
isdn spid1 51255511110101 5551111
isdn spid2 51255511120101 5551112
ppp authentication chap
ppp multilink
!--- allow multilink connections
!
! <<--unused interface configurations have been removed.
!
router ospf 5
network 172.20.10.0 0.0.0.255 area 0
network 172.22.1.0 0.0.0.255 area 0
network 172.22.53.0 0.0.0.255 area 0
default-information originate always
!--- transmit OSPF default information
!--- This may be required for remote router to use the BRI DDR link.
!
ip classless
ip route 0.0.0.0 0.0.0.0 Ethernet0/0
ip route 172.22.0.0 255.255.0.0 172.22.53.0
no ip http server
!
dialer-list 1 protocol ip permit
!--- All IP traffic is defined interesting.
!--- This is applied to BRI0 using dialer-group 1.
!
line con 0
login authentication NO_AUTHEN
transport input none
line 97 102
line aux 0
line vty 0 4
!
end
【责编:admin】
--------------------next---------------------
阅读(268) | 评论(0) | 转发(0) |
