3.2 实验1:机启动及基木设置
本实验是对 Catalyst 1900系列机的启动和基本设置的操作。
1.实验目的
通过本实验，读者可以掌握以下技能
熟悉交换机的开机界面;
对交换机进行基本的设置;
理解交换机的端口及其编号。
2.设备需求
本实验需要以下设备:
Catalyst 1900系列交换机1台，型号不限，企业版软件，本实验中使用了1912交换机;
PC机1台，操作系统为系列。装有超级终端程序;
Console电缆1条及相应的接口转换器。
3.线缆连接及配置说明
如图3.1所示，PC机通过串口与交换机的Console端口相连。
和器一样，Cisco交换机的Console端口的缺省设置如下
端口速率:9600bit/s
数据位:8
奇偶校验:无
停止位:1
流控:无
把PC机超级终端程序中串行端口的属性设置成与上述参数一致后，便可以开始实验。
4.实验配置及监测结果
在PC机启动正常，PC机与交换机使用Console电缆连接起来，并且已经进入超级终端程序的情况下。接通交
换机电源。
由于交换机没有电源开关，接通电源即直接插上电源插头。
监测清单3.1记录了Catalyst 1912交换机启动的全过程。
监测清单3-1 Catalyst 1912交换机启动及基本配置
第1段：交换机的启动
Catalyst 1900 Management Console
Copyright (c) Cisco Systems, Inc. 1993-1999
All rights reserved.
Emter[rose Edotopm Software
Ethernet Address: 00-04-DD-4E-9C-80
PCA Number: 73-3122-04
PCA Serial Number: FAB0503D0B4
Model Number: WS-C1912-EN
System Serial Number: FAB0503W0FA
Power Supply S/N PHI044207FR
PCB Serial Number: FAB0503D0B4,73-3122-04
1 user(s)now active on Management Console.
User Interface Menu
[M] Menus
[K] Command Line
[1] IP Configuration
[P] Console Password
Enter Selection:
第2段：进行交换机基本配置
Enter Selection: K
CLI session with the switch is open.
To end the CLI session, enter [Exit].
>?
Exec commands:
enable Turn on privileged commands
exit Exit from the EXEC
help Description of the interactive help system
ping Send echo messages
session Tunnel to module
show Show running system information
terminal Set terminal line parameters
>enable
#
#conft
Enter configuration commands, one per line. End with CNTL/Z
(config)#?
Configure commands:
address-violation Set address violation action
back-pressure Enable back pressure
banner Define a login banner
bridge-group Configure port grouping using bridge groups
cdp Global CDP configuration subcommands
cgroup Enable CGMP
cluster Cluster configuration commands
ecc Enable enhanced congestion control
enable Modift enable password parameters
end Exit from configure mode
exit Exit from configure mode
help Description of the interactive help system
hostname Set the system's network name
interface Select an interface to configure
ip Global IP configureation subcommands
line Configure a terminal line
login Configure options for logging in
mac-address-table Configure the mac address table
monitor-port Set port monitoring
--More--
mlilticast-store-and-forward Enables multicast store and forward
network-port Set the network port
no Negate a cominand or set its defaults
port-channel Configure Fast EtherChannel
rip Routing information protocol configuration
service Configuration Command
sump-server Modify SNMP parameters
spantree Spanning subsystem
spantree-template Set bridge template parameter
storm-control Configure broadcast storm contfolpirameters
switching-mode Set the switching mode
tacacs-server Modify TACACS query parameters
tftp Configure TFTP
uplink-fast Enable Uplink fast
vlan VLAN configuration
vlan-membership VLAN membership server configuration
vtp Global VTP configuration commands
(config)#SiostBiame SW1912
SW1912(config)#enabSe password ?
level Set exec level password
SW1912(config)#enable password level 1 pass1
SW1912(config)#enabSe password level 15 passl5
SW1912(config)#enable secret Cisco
SW1912#disable
SW1912>
SW1912>en
Enter password: ***** ( 键入cisco )
SW1912#conf t
Enter configuration commands, one per line. End with CNTL/Z
SW1912(config)#ip address 192.168.1.1255.255.255.0
SW1912(config)#ip default-gateway 192.168.1.254
SW1912(config)#ip domain-name ?
WORD Domain name
SW1912(config)#ip domain-name cisco.com
SW1912(config)#ip name-server 200.1.1.1
SW1912(config)#end
SW1912#sh version
Cisco Catalyst 1900/2820 Enterprise Edition Software
Version V9.00,05 written from 192.168.000.005
Copyright (c) Cisco Systems, Inc. 1993-1999
SW1912 uptime is 0day(s)00hour(s)12minute(s)44secibd(s)
cisco Catalyst 1900(486sxl)processor with 2048K/1024K bytes of memory
Hardware board revision is 5
Upgrade Status: No upgrade currently in progress.
Config File Status: No configuration upload/download is in progress
15 Fixed Ethernet/IEEE802.3interface(s)
Base Ethernet Address: 00-04-DD-4E-9C-80
SW1912#show ip
IP Address:192.168.1.1
Subnet Mask:255.255.255.0
Default Gateway:192.168.1.254
Management VLANl: 1
Domain name:cisco.com
Name server1:200.1.1.1
HTTP server:Enabled
HTTP port: 80
RIP:Enabled
SW1912#show running-config
Building configuration...
Current configuration:
!
tftp accept
tftp server "192.168.0.5"
tftp filename "catl900EN.9.00.05.bin"
!
hostname "SW1912"
!
ip address 192.168.1.1255.255.255.0
ip default-gateway 192.168.1.254
ip domain-name "cisco.com"
ip name-server 200.1.1.1
!
enable secret 5 $l$FMFQ$mlNHW7EzaJpG9uhKPWBvf/
enable password level 1 "PASS 1"
enable password level 15 "PASS 15"
!
interface Ethernet 0/1
!
interface Ethernet 0/2
!
interface Ethernet 0/3
!
interface Ethernet 0/4
!
interface Ethernet 0/5
!
interface Ethernet 0/6
!
interface Ethernet 0/7
!
interface Ethernet 0/8
!
interface Ethernet 0/9
interface Ethernet 0/10
!
interface Ethernet 0/11
!
interface Ethernet 0/12
!
interface Ethernet 0/25
!
interface FastEthernet 0/26
!
interface FastEthernet 0/27
!
line console
end
SW1912#show int e0/l
Ethernet 0/1 is Suspended-no-linkbeat
802.1 dSTP State: Forwarding Forward Transitions:1
Port monitoring: Disabled
Unknown unicast flooding: Enabled
Unregistered multicast flooding: Enabled
Description:
Duplex setting: Half duplex
Back pressure: Disabled
Receive Statistics Transmit Statistics
Total good frames 0 Total frames 0
Total octets 0 Total octets 0
Broadcast/multicast frames 0 Broadcast/multicast frames 0
Broadcast/multicast octets 0 Broadcast/multicast octets 0
Good frames forwarded 0 Deferrals 0
Frames filtered 0 Single collisions 0
Runt frames 0 Multiple collisions 0
No buffer discards 0 Excessive collisions 0
Queue full discards 0
Errors: Errors:
【责编:admin】
--------------------next---------------------
