分类： LINUX
2009-03-24 15:12:50
#define __REGb(x) (*(volatile unsigned char *)(x))
#define __REGi(x) (*(volatile unsigned int *)(x))
#define NF_BASE 0x4e000000
#define NFCONF __REGi(NF_BASE + 0x0)
#define NFCMD __REGb(NF_BASE + 0x4)
#define NFADDR __REGb(NF_BASE + 0x8)
#define NFDATA __REGb(NF_BASE + 0xc)
#define NFSTAT __REGb(NF_BASE + 0x10)
#define BUSY 1
inline void wait_idle(void) {
int i;
while(!(NFSTAT & BUSY))
for(i=0; i<10; i++);
}
/* low level nand read function */
int
nand_read_ll(unsigned char *buf, unsigned long start_addr, int size)
{
int i, j;
if ((start_addr & NAND_BLOCK_MASK) || (size & NAND_BLOCK_MASK)) {
return -1; /* invalid alignment */
}
/* chip Enable */
NFCONF &= ~0x800;
for(i=0; i<10; i++);
for(i=start_addr; i < (start_addr + size);) {
/* READ0 */
NFCMD = 0;
/* Write Address */
NFADDR = i & 0xff;
NFADDR = (i >> 9) & 0xff;
NFADDR = (i >> 17) & 0xff;
NFADDR = (i >> 25) & 0xff;
wait_idle();
for(j=0; j < NAND_SECTOR_SIZE; j++, i++) {
*buf = (NFDATA & 0xff);
buf++;
}
}
/* chip Disable */
NFCONF |= 0x800; /* chip disable */
return 0;
}
3 修改board/tekkaman/tekkaman2410/Makefile文件
......
OBJS := tekkaman2410.o nand_read.o
......
4 修改include/configs/tekkaman2410.h文件，添加如下内容：
......
/*
* Nandflash Boot
*/
#define CONFIG_S3C2410_NAND_BOOT 1
#define STACK_BASE 0x33f00000
#define STACK_SIZE 0x8000
//#define UBOOT_RAM_BASE 0x33f80000
/* NAND Flash Controller */
#define NAND_CTL_BASE 0x4E000000
#define bINT_CTL(Nb) __REG(INT_CTL_BASE + (Nb))
/* Offset */
#define oNFCONF 0x00
#define oNFCMD 0x04
#define oNFADDR 0x08
#define oNFDATA 0x0c
#define oNFSTAT 0x10
#define oNFECC 0x14
#endif /* __CONFIG_H */
5 修改board/tekkaman/tekkaman2410/lowlevel_init.S文件
依照开发箱的内存区的配置情况, 修改board/tekkaman/tekkaman2410/lowlevel_init.S文件，我利用博创提供的vivi源码里的信息做了如下更改:
......
#define B1_BWSCON (DW16) /*@tekkaman*/
#define B2_BWSCON (DW16)
#define B3_BWSCON (DW16) /*@tekkaman*/
#define B4_BWSCON (DW16)
#define B5_BWSCON (DW16)
#define B6_BWSCON (DW32)
#define B7_BWSCON (DW32)
......
#define B3_Tacs 0x0 /* 0clk */
#define B3_Tcos 0x0 /* 0clk @tekkaman*/
#define B3_Tacc 0x7 /* 14clk */
#define B3_Tcoh 0x0 /* 0clk @tekkaman*/
#define B3_Tah 0x0 /* 0clk */
#define B3_Tacp 0x0 /*@tekkaman*/
#define B3_PMC 0x0 /* normal */
......
注：之所以Bank3的改动较大，是因为smdk2410的网卡CS8900是在Bank3，而博创2410－S的AX88796是在Bank2。
......
.word ((B7_MT<<15)+(B7_Trcd<<2)+(B7_SCAN))
.word ((REFEN<<23)+(TREFMD<<22)+(Trp<<20)+(Trc<<18)+(Tchr<<16)+REFCNT)
.word 0xb2 /*@tekkaman*/
.word 0x30
.word 0x30
6 修改/board/tekkaman/tekkaman2410/tekkaman2410.c
因为博创2410－S和smdk2410的GPIO连接有所不同，我依旧利用博创配的vivi，修改其对GPIO的配置(具体原因我并未深究，请参阅博创2410－S的硬件说明和2410芯片手册)：
......
gpio->GPEUP = 0x0000FFFF;
gpio->GPFCON = 0x000051aa; //0x000055AA; tekkaman
gpio->GPFUP = 0x000000ef; //0x000000FF; tekkaman
gpio->GPGCON = 0xfd95ffba; //0xFF95FFBA; tekkaman
gpio->GPGUP = 0x0000efff; //0x0000FFFF; tekkaman
gpio->GPHCON = 0x0016faaa; //0x002AFAAA; tekkaman
gpio->GPHUP = 0x000007FF;
......
7 为了实现NAND Flash的读写，再次修改
//具体内容请参阅对《U-BOOT下使用bootm引导内核方法》的补充说明
......
#define CFG_LONGHELP
/* undef to save memory */
#define CFG_PROMPT "[Tekkaman2410]#"
/*Monitor Command Prompt */
#define CFG_CBSIZE 256
/* Console I/O Buffer Size */
......
#define CFG_LOAD_ADDR 0x30008000
/* default load address */
......
//#define PHYS_FLASH_1 0x00000000 /* Flash Bank #1 */
//#define CFG_FLASH_BASE PHYS_FLASH_1
/*-----------------------------------------------------------------------
* FLASH and environment organization
*/
#define CFG_NO_FLASH 1
#if 0
#define CONFIG_AMD_LV400 1 /* uncomment this if you have a LV400 flash */
//#if 0
#define CONFIG_AMD_LV800 1 /* uncomment this if you have a LV800 flash */
#endif
//#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
......
/* timeout values are in ticks */
//#define CFG_FLASH_ERASE_TOUT (5*CFG_HZ)
/* Timeout for Flash Erase */
//#define CFG_FLASH_WRITE_TOUT (5*CFG_HZ)
/* Timeout for Flash Write */
#define CFG_ENV_IS_IN_NAND 1
#define CFG_ENV_OFFSET 0X20000
//#define ENV_IS_EMBEDDED 1
#define CFG_NAND_LEGACY
#define CFG_ENV_SIZE 0x10000
/* Total Size of Environment Sector */
#if (CONFIG_COMMANDS & CFG_CMD_NAND)
#define CFG_NAND_BASE 0x4E000000
/* NandFlash控制器在SFR区起始寄存器地址 */
#define CFG_MAX_NAND_DEVICE 1
/* 支持的最在Nand Flash数据 */
#define SECTORSIZE 512
/* 1页的大小 */
#define NAND_SECTOR_SIZE SECTORSIZE
#define NAND_BLOCK_MASK 511
/* 页掩码 */
#define ADDR_COLUMN 1
/* 一个字节的Column地址 */
#define ADDR_PAGE 3
/* 3字节的页块地址!!!!!*/
#define ADDR_COLUMN_PAGE 4
/* 总共4字节的页块地址!!!!! */
#define NAND_ChipID_UNKNOWN 0x00
/* 未知芯片的ID号 */
#define NAND_MAX_FLOORS 1
#define NAND_MAX_CHIPS 1
/* Nand Flash命令层底层接口函数 */
#define WRITE_NAND_COMMAND(d, adr) {rNFCMD = d;}
#define WRITE_NAND_ADDRESS(d, adr) {rNFADDR = d;}
#define WRITE_NAND(d, adr) {rNFDATA = d;}
#define READ_NAND(adr) (rNFDATA)
#define NAND_WAIT_READY(nand) {while(!(rNFSTAT&(1<<0)));}
#define NAND_DISABLE_CE(nand) {rNFCONF |= (1<<11);}
#define NAND_ENABLE_CE(nand) {rNFCONF &= ~(1<<11);}
/* the following functions are NOP's because S3C24X0 handles this in hardware 一定要加上 */
#define NAND_CTL_CLRALE(nandptr)
#define NAND_CTL_SETALE(nandptr)
#define NAND_CTL_CLRCLE(nandptr)
#define NAND_CTL_SETCLE(nandptr)
/* 允许Nand Flash写校验 */
#define CONFIG_MTD_NAND_VERIFY_WRITE 1
*
* Nandflash Boot
*/
#define CONFIG_S3C2410_NAND_BOOT 1
#define STACK_BASE 0x33f00000
#define STACK_SIZE 0x8000
//#define UBOOT_RAM_BASE 0x33f80000
/* NAND Flash Controller */
#define NAND_CTL_BASE 0x4E000000
#define bINT_CTL(Nb) __REG(INT_CTL_BASE + (Nb))
/* Offset */
#define oNFCONF 0x00
#define oNFCMD 0x04
#define oNFADDR 0x08
#define oNFDATA 0x0c
#define oNFSTAT 0x10
#define oNFECC 0x14
#define rNFCONF (*(volatile unsigned int *)0x4e000000)
#define rNFCMD (*(volatile unsigned char *)0x4e000004)
#define rNFADDR (*(volatile unsigned char *)0x4e000008)
#define rNFDATA (*(volatile unsigned char *)0x4e00000c)
#define rNFSTAT (*(volatile unsigned int *)0x4e000010)
#define rNFECC (*(volatile unsigned int *)0x4e000014)
#define rNFECC0 (*(volatile unsigned char *)0x4e000014)
#define rNFECC1 (*(volatile unsigned char *)0x4e000015)
#define rNFECC2 (*(volatile unsigned char *)0x4e000016)
#endif /* CONFIG_COMMANDS & CFG_CMD_NAND*/
#endif /* __CONFIG_H */
8
static struct nand_flash_dev nand_flash_ids[] = {
......{NULL,}
};
9 修改/lib_arm中的board.c。
static int display_banner (void)
{
printf ("\n\n%s\n\n", version_string);
debug ("U-Boot code: %08lX -> %08lX BSS: -> %08lX\n",
_armboot_start, _bss_start, _bss_end);
printf ("U-Boot code: %08lX -> %08lX BSS: -> %08lX\n", //tekkaman
_armboot_start, _bss_start, _bss_end); //tekkaman
#ifdef CONFIG_MODEM_SUPPORT
debug ("Modem Support enabled\n");
#endif
#ifdef CONFIG_USE_IRQ
debug ("IRQ Stack: %08lx\n", IRQ_STACK_START);
debug ("FIQ Stack: %08lx\n", FIQ_STACK_START);
#endif
return (0);
}
ret = nand_legacy_rw(nand_dev_desc + 0,
0x00 | 0x02, CFG_ENV_OFFSET, CFG_ENV_SIZE,
&total, (u_char*)env_ptr);
u-boot运行至第二阶段进入start_armboot()函数。其中nand_init()函数是对nand flash的最初初始化函数。Nand_init()函数在两个文件中实现。其调用与CFG_NAND_LEGACY宏有关，如果没有定义这个宏，系统调用 drivers/nnd/nand.c中的nand_init()；否则调用自己在board/smdk2410/smdk2410.c中的nand_init()函数。这里我选择第二种方式。
#if (CONFIG_COMMANDS & CFG_CMD_NAND)
typedef enum {
NFCE_LOW,
NFCE_HIGH
} NFCE_STATE;
static inline void NF_Conf(u16 conf)
{
S3C2410_NAND * const nand = S3C2410_GetBase_NAND();
nand->NFCONF = conf;
}
static inline void NF_Cmd(u8 cmd)
{
S3C2410_NAND * const nand = S3C2410_GetBase_NAND();
nand->NFCMD = cmd;
}
static inline void NF_CmdW(u8 cmd)
{
NF_Cmd(cmd);
udelay(1);
}
static inline void NF_Addr(u8 addr)
{
S3C2410_NAND * const nand = S3C2410_GetBase_NAND();
nand->NFADDR = addr;
}
static inline void NF_SetCE(NFCE_STATE s)
{
S3C2410_NAND * const nand = S3C2410_GetBase_NAND();
switch (s) {
case NFCE_LOW:
nand->NFCONF &= ~(1<<11);
break;
case NFCE_HIGH:
nand->NFCONF |= (1<<11);
break;
}
}
static inline void NF_WaitRB(void)
{
S3C2410_NAND * const nand = S3C2410_GetBase_NAND();
while (!(nand->NFSTAT & (1<<0)));
}
static inline void NF_Write(u8 data)
{
S3C2410_NAND * const nand = S3C2410_GetBase_NAND();
nand->NFDATA = data;
}
static inline u8 NF_Read(void)
{
S3C2410_NAND * const nand = S3C2410_GetBase_NAND();
return(nand->NFDATA);
}
static inline void NF_Init_ECC(void)
{
S3C2410_NAND * const nand = S3C2410_GetBase_NAND();
nand->NFCONF |= (1<<12);
}
static inline u32 NF_Read_ECC(void)
{
S3C2410_NAND * const nand = S3C2410_GetBase_NAND();
return(nand->NFECC);
}
#endif
/** NAND flash initialization.
*/
#if (CONFIG_COMMANDS & CFG_CMD_NAND)
extern ulong nand_probe(ulong physadr);
static inline void NF_Reset(void)
{
int i;
NF_SetCE(NFCE_LOW);
NF_Cmd(0xFF); /* reset command */
for(i = 0; i < 10; i++); /* tWB = 100ns. */
NF_WaitRB(); /* wait 200~500us; */
NF_SetCE(NFCE_HIGH);
}
static inline void NF_Init(void)
{
#if 0 /* a little bit too optimistic */
#define TACLS 0
#define TWRPH0 3
#define TWRPH1 0
#else
#define TACLS 0
#define TWRPH0 4
#define TWRPH1 2
#endif
NF_Conf((1<<15)|(0<<14)|(0<<13)|(1<<12)|(1<<11)|(TACLS<<8)|(TWRPH0<<4)|(TWRPH1<<0));
/*nand->NFCONF = (1<<15)|(1<<14)|(1<<13)|(1<<12)|(1<<11)|(TACLS<<8)|(TWRPH0<<4)|(TWRPH1<<0); */
/* 1 1 1 1, 1 xxx, r xxx, r xxx */
/* En 512B 4step ECCR nFCE=H tACLS tWRPH0 tWRPH1 */
NF_Reset();
}
void
nand_init(void)
{
S3C2410_NAND * const nand = S3C2410_GetBase_NAND();
NF_Init();
#ifdef DEBUG
printf("NAND flash probing at 0x%.8lX\n", (ulong)nand);
#endif
printf ("%4lu MB\n", nand_probe((ulong)nand) >> 20);
}
#endif
