开发板启动Log

伟研科技

U-Boot 1.3.0-rc3 (Mar 31 2008 - 21:31:05)
WEIYAN TECHNOLOGY

DRAM:  64 MB
dm9000 i/o: 0x18000300, id: 0x90000a46
MAC: 00:0c:20:02:0a:5b
NAND:  64 MiB
In:    serial
Out:   serial
Err:   serial
Hit any key to stop autoboot:  0
dm9000 i/o: 0x18000300, id: 0x90000a46
MAC: 00:0c:20:02:0a:77
TFTP from server 192.168.1.5; our IP address is 192.168.1.6
Filename 'uImage'.
Load address: 0x31000000
Loading: #################################################################
         ###########################################
done
Bytes transferred = 1554488 (17b838 hex)
## Booting image at 31000000 ...
   Image Name:   Linux-2.6.24.4
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1554424 Bytes =  1.5 MB
   Load Address: 30008000
   Entry Point:  30008000
   Verifying Checksum ... OK
OK

Starting kernel ...

Uncompressing Linux................................................................................................... done, booting the kernel.
Linux version 2.6.24.4 (WEIYAN ) (gcc version 3.4.1) #6 Tue Apr 1 01:35:30 CST 2008
CPU: ARM920T [41129200] revision 0 (ARMv4T), cr=c0007177
Machine: SMDK2440
Memory policy: ECC disabled, Data cache writeback
CPU S3C2440A (id 0x32440001)
S3C244X: core 406.425 MHz, memory 135.475 MHz, peripheral 67.737 MHz
S3C24XX Clocks, (c) 2004 Simtec Electronics
CLOCK: Slow mode (2.116 MHz), fast, MPLL on, UPLL on
CPU0: D VIVT write-back cache
CPU0: I cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
CPU0: D cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
Kernel command line: root=/dev/mtdblock1 rootfstype=yaffs console=ttySAC0 ip=192.168.1.6:192.168.1.5:192.168.1.5:255.255.255.0:WEIYAN:eth0:off
irq: clearing pending ext status 00080b00
irq: clearing subpending status 00000002
PID hash table entries: 256 (order: 8, 1024 bytes)
timer tcon=00500000, tcnt dc7f, tcfg 00000200,00000000, usec 000016ad
Console: colour dummy device 80x30
console [ttySAC0] enabled
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 64MB = 64MB total
Memory: 61696KB available (2804K code, 267K data, 112K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
net_namespace: 64 bytes
NET: Registered protocol family 16
S3C2410 Power Management, (c) 2004 Simtec Electronics
S3C2440: Initialising architecture
S3C2440: IRQ Support
S3C2440: Clock Support, DVS off
S3C24XX DMA Driver, (c) 2003-2004,2006 Simtec Electronics
DMA channel 0 at c4800000, irq 33
DMA channel 1 at c4800040, irq 34
DMA channel 2 at c4800080, irq 35
DMA channel 3 at c48000c0, irq 36
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NetWinder Floating Point Emulator V0.97 (double precision)
JFFS2 version 2.2. (NAND) 漏 2001-2006 Red Hat, Inc.
yaffs Mar 31 2008 18:43:57 Installing.
io scheduler noop registered
io scheduler deadline registered (default)
Console: switching to colour frame buffer device 30x40
fb0: s3c2410fb frame buffer device
s3c2440-uart.0: s3c2410_serial0 at MMIO 0x50000000 (irq = 70) is a S3C2440
s3c2440-uart.1: s3c2410_serial1 at MMIO 0x50004000 (irq = 73) is a S3C2440
s3c2440-uart.2: s3c2410_serial2 at MMIO 0x50008000 (irq = 76) is a S3C2440
RAMDISK driver initialized: 4 RAM disks of 4096K size 1024 blocksize
loop: module loaded
dm9000 Ethernet Driver
eth0: dm9000 at c4852300,c4854304 IRQ 51 MAC: 00:0c:20:02:0a:77
Linux video capture interface: v2.00
Driver 'sd' needs updating - please use bus_type methods
S3C24XX NAND Driver, (c) 2004 Simtec Electronics
s3c2440-nand s3c2440-nand: Tacls=2, 14ns Twrph0=4 29ns, Twrph1=2 14ns
NAND device: Manufacturer ID: 0xec, Chip ID: 0x76 (Samsung NAND 64MiB 3,3V 8-bit)
Scanning device for bad blocks
Creating 3 MTD partitions on "NAND 64MiB 3,3V 8-bit":
0x00000000-0x00200000 : "BOOT"
0x00200000-0x02200000 : "ROOTFS"
0x02200000-0x04000000 : "BACKUP"
s3c2410-ohci s3c2410-ohci: S3C24XX OHCI
s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1
s3c2410-ohci s3c2410-ohci: irq 42, io mem 0x49000000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
s3c2410_udc: debugfs dir creation failed -19
s3c2440-usbgadget s3c2440-usbgadget: S3C2440: increasing FIFO to 128 bytes
mice: PS/2 mouse device common for all mice
wake enabled for irq 19
s3c-buttons s3c-buttons: successfully loaded
input: s3c-buttons as /class/input/input0
s3c2410 TouchScreen successfully loaded
input: s3c2410 TouchScreen as /class/input/input1
S3C24XX RTC, (c) 2004,2006 Simtec Electronics
s3c2410-rtc s3c2410-rtc: rtc disabled, re-enabling
s3c2410-rtc s3c2410-rtc: rtc core: registered s3c as rtc0
s3c2440-i2c s3c2440-i2c: slave address 0x10
s3c2440-i2c s3c2440-i2c: bus frequency set to 384 KHz
s3c2440-i2c s3c2440-i2c: i2c-0: S3C I2C adapter
S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics
s3c2410-wdt s3c2410-wdt: watchdog inactive, reset disabled, irq enabled
wy-sdi s3c2410-sdi: powered down.
wy-sdi s3c2410-sdi: initialisation done.
UDA1341 audio driver initialized
TCP cubic registered
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
s3c2410-rtc s3c2410-rtc: setting system clock to 2008-04-02 19:19:23 UTC (1207163963)
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
IP-Config: Complete:
      device=eth0, addr=192.168.1.6, mask=255.255.255.0, gw=192.168.1.5,
     host=WEIYAN, domain=, nis-domain=(none),
     bootserver=192.168.1.5, rootserver=192.168.1.5, rootpath=
yaffs: dev is 32505857 name is "mtdblock1"
yaffs: passed flags ""
yaffs: Attempting MTD mount on 31.1, "mtdblock1"
VFS: Mounted root (yaffs filesystem).
Freeing init memory: 112K
wy-sdi s3c2410-sdi: running at 22579kHz (requested: 25000kHz).
wy-sdi s3c2410-sdi: running at 22579kHz (requested: 25000kHz).
mmc0: new SD card at address abcd
mmcblk0: mmc0:abcd SD032 256000KiB
 mmcblk0: p1
init started: BusyBox v1.9.1 (2008-03-31 12:07:59 CST)
starting pid 256, tty '': '/etc/init.d/rcS'
starting initial script, WEIYAN

Please press Enter to activate this console.