Sun v880上安装emulex HBA，配置Storage Node详细步骤

时间：2005-3-4
任务：在Sun v880上加装Emulex LP9002L-F2光纤卡，用来识别P4000磁带库及带机

实施步聚：
1. 关闭v880上的所有应用
2. 关闭系统，切断电源
3. 安装HBA卡到PCI槽
4. 开机，正常启动Solaris系统
5. 以root用户登录到系统，安装lpfc.1驱动程序包，pkgadd –d ./ lpfc.1
6. 修改/kernel/drv/st.conf，增加target数量及lun数量，st.conf如下：
#
# Copyright (c) 1995-2000 by Sun Microsystems, Inc.
# All rights reserved.
#
#
#pragma ident   "@(#)st.conf    1.31    00/08/24 SMI"
#

# This file contains configuration entries for both officially supported
# devices of Sun Microsystems and many 3rd party devices.
#
# The officially supported devices are :
#
#   "ARCHIVE Python 28388"                                  Note 1
#   "ARCHIVE Python 28454"                                  Note 1
#   "ARCHIVE Python 29279"                                  Note 1
#   "ARCHIVE VIPER 150"                                     Note 1
#   "EXABYTE EXB-8200"                                      Note 1
#   "EXABYTE EXB-8500"                                      Note 1
#   "EXABYTE EXB-8505"                                      Note 1
#   "EXABYTE EXB-8900"                                      Note 1
#   "HP      88780"                                         Note 1
#   "HP      C5683A"                                        Note 1
#   "HP      C5713A"                                        Note 1
#   "Quantum DLT4000"                                       Note 1
#   "Quantum DLT7000"                                       Note 1
#   "Quantum DLT8000"                                       Note 1
#   "STK     9840"                                          Note 1
#   "SUN     DLT4000"                                       Note 1
#   "SUN     DLT4700"                                       Note 1
#   "SUN     DLT7000"                                       Note 1
#   "TANDBERG SLR5"                                         Note 1
#   "TANDBERG TDC 4200"                                     Note 1
#   "TANDBERGMLR1"                                          Note 1
#   "TANDBERGMLR3"                                          Note 1
#
# The unsupported devices are :
#
#   "Emulex  MTO2"                                          Note 1
#   "ANRITSU DMT2120"                                       Note 1
#   "ARCHIVE Python 04106"                                  Note 1
#   "ARCHIVE VIPER 255"                                     Note 1
#   "DEC     DLT2"
#   "DEC     TZ87"
#   "EXABYTE EXB-2501"                                      Note 1
#   "EXABYTE EXB-4200c"                                     Note 1
#   "EXABYTE EXB8500C"
#   "FUJITSU M1016B  M2483B"
#   "FUJITSU M248"
#   "HP      C1533A"                                        Note 1
#   "HP      C1553A  "
#   "HP      C1537A"                                        Note 1
#   "HP      C1557A"                                        Note 1
#   "HP      HP35470A"                                      Note 1
#   "HP      HP35480A"                                      Note 1
#   "IBM     03490"
#   "IBM     9348"
#   "KENNEDY"                                               Note 1
#   "LMS"                                                   Note 1
#   "M4 DATA 123107 SCSI"                                   Note 1
#   "Metrum"
#   "R-BYTE  RB100"
#   "Seagate STT20000N"                                     Note 1
#   "SONY    SDT-5000"                                      Note 1
#   "SONY    SDT-5200"                                      Note 1
#   "STK     9490"
#   "STK     4280"
#   "STK"                                                   Note 1
#   "TANDBERG 4100"                                         Note 1
#   "TANDBERG 4200"                                         Note 1
#   "TELEX"
#   "WANGTEK 51000  SCSI"
#   "WANGTEK 5150ES"                                        Note 1
#   "WANGTEK 5525ES SCSI"                                   Note 1
#   "WANGTEK 6130-HS"                                       Note 1
#   "WangDAT Model 2600"                                    Note 1
#   "WangDAT Model 3400"                                    Note 1
#   "WangDAT"                                               Note 1
#   "7600"                                              Note 1
#
# Notes
# -----
#   1   Drive is configured automatically - no entry is needed in st.conf.
#
# The 3rd party devices do apparently work with the configurations listed.
# All the entries have been taken from the net and probably have worked in
# the past, but have not been tested by Sun Microsystems. Use these entries
# as your starting point for generating your configuration entries.
#
#
tape-config-list=
#"HP Ultrium 2-SCSI", "HP LTO Ultrium Generation 2", "Class_HP460",
#"Emulex  MTO2",           "Emulex MT02 QIC-11/QIC-24",        "MT02",
#"ANRITSU DMT2120",        "Unisys 1/2" Reel",                "ANRITSU",
#"ARCHIVE Python 04106",   "Seagate Scorpion 24 DDS3 DAT",     "ARCH_04106",
#"ARCHIVE Python 28454",   "Archive Python 4mm Helical Scan",  "ARCH_Python",
#"ARCHIVE Python 29279",   "Archive Python 4mm DAT Stacker",   "ARCH_Python",
#"ARCHIVE Python 28388",   "Archive/Conner CTDX004 4mm DAT",   "Conner2-DAT",
#"ARCHIVE VIPER 150",      "Archive QIC-150",                  "QIC150",
#"ARCHIVE VIPER 255",      "Archive QIC-525",                  "QIC150",
#"DEC     DLT2",           "DEC DLT",                          "DLT2",
#"DEC     TZ87",           "DEC DLT",                          "DLT2",
#"EXABYTE EXB-2501",       "Exabyte EXB-2501 QIC",             "EXB-2501",
#"EXABYTE EXB-4200c",      "Exabyte 4mm Helical Scan",         "Exa4200c",
#"EXABYTE EXB-8200",       "Exabyte EXB-8200 8mm Helical Scan","EXB-8200",
#"EXABYTE EXB-8500",       "Exabyte EXB-8500 8mm Helical Scan","EXB-850X",
#"EXABYTE EXB-8505",       "Exabyte EXB-8505 8mm Helical Scan","EXB-850X",
#"EXABYTE EXB8500C",       "Exabyte 8500C 8mm Helical Scan",   "EXB-850X",
#"FUJITSU M1016B  M2483B", "Fujitsu 1/2" Cartridge",          "Fujitsu_comp",
#"FUJITSU M248",           "Fujitsu 1/2" Cartridge",          "Fujitsu_m248x",
#"HP      88780",          "HP-88780 1/2" Reel",              "HP_half",
#"HP      C1533A",         "HP DDS2 4mm DAT loader",           "HP_DAT",
#"HP      C1553A  ",       "HP C1553A 4mm DAT",                "HP_DAT",
#"HP      C1537A",         "HP DDS-3 4mm DAT ",                "HP_DAT_3",
#"HP      C1557A",         "HP DDS-3 4mm DAT loader",          "HP_DAT_3",
#"HP      HP35470A",       "HP 35470A 4mm DAT",                "HP_DAT",
#"HP      HP35480A",       "HP 35480A 4mm DAT",                "HP_DAT",
#"IBM     03490",          "IBM 3490E 1/2" Cartridge",        "CLASS_3490",
#"IBM     9348",           "STK 4220 1/2" Cartridge",         "C3490",
#"KENNEDY",                "Kennedy 1/2" Reel",               "KENNEDY",
#"LMS",                    "CDC 1/2" Cartridge",              "LMS",
#"M4 DATA 123107 SCSI",    "M4-Data 1/2" Reel",               "M4_DATA",
#"Metrum",                 "Metrum VHS Cartridge",             "MetD",
#"QUANTUM DLT7000",        "Quantum DLT7000",                  "DLT7k-data",
#"SUN     DLT7000",        "Sun DLT7000",                      "DLT7k-data",
#"Quantum DLT4000",        "Quantum DLT4000",                  "DLT-data",
#"SUN     DLT4000",        "DLT4000",                          "DLT-data",
#"SUN     DLT4700",        "DLT4700 Library",                  "DLT-data",
#"R-BYTE  RB100",          "R-Byte Whozits",                   "DAT",
#"Seagate STT20000N",      "Seagate Hornet NS20 Travan",       "NS20",
#"SONY    SDT-5000",       "SONY 4mm DAT",                     "DAT",
#"SONY    SDT-5200",       "SONY 4mm DAT",                     "DAT",
#"STK     9490",           "STK 9490 1/2" Cartridge",         "CLASS_3490",
#"STK     4280",           "STK 4280 1/2" Cartridge",         "C3490",
#"STK",                    "STK 1/2" Cartridge",              "CLASS_3490",
#"TANDBERG 4100",          "Tandberg 4100 QIC",                "TAND_4100_QIC",
#"TANDBERG 4200",          "Tandberg 4200 QIC",                "TAND_4200_QIC",
#"TANDBERG TDC 4200",      "Tandberg QIC 2.5 Gig Tape Drive",  "TANDB-2_5G",
#"TANDBERG SLR5",          "Tandberg 8 Gig QIC",               "TAND-8G-VAR",
#"TANDBERGMLR1",           "Tandberg MLR1 QIC",                "TANDBERG_MLR1",
#"TANDBERGMLR3",           "Tandberg 50 Gig QIC",              "TAND-50G-VAR",
#"TELEX",                  "STK 4220 1/2" Cartridge",         "C3490",
#"WANGTEK 51000  SCSI",    "Wangtek 1.2GB QIC",                "WtQIC",
#"WANGTEK 5150ES",         "Wangtek QIC-150",                  "WANGTEK_QC150",
#"WANGTEK 5525ES SCSI",    "Wangtek 525MB QIC",                "WtQIC",
#"WANGTEK 6130-HS",        "Wangtek 4mm Helical Scan",         "WANGTEK_6130",
#"WangDAT Model 2600",     "WangDAT 4mm DAT",                  "WangDAT",
#"WangDAT Model 3400",     "WangDAT 4mm DAT",                  "WangDAT",
#"WangDAT",                "Wang DAT 3.81 Helical Scan",       "WangDAT",
#"7600",               "Fujitsu 1/2" Cartridge",          "Fujitsu_half";

#ANRITSU       = 1, 0x25,    0, 0x0041D, 4, 0x00, 0x02, 0x03, 0x03, 1;
#ARCH_04106    = 1, 0x2C,    0, 0x09639, 4, 0x00, 0x8C, 0x8C, 0x8C, 3;
#ARCH_Python   = 1, 0x2C,    0, 0x0DE39, 4, 0x00, 0x8C, 0x8C, 0x8C, 3;
#CLASS_3490    = 1, 0x24,    0, 0x1C43D, 4, 0x00, 0x00, 0x00, 0x00, 0;
#C3490         = 1, 0x24,    0, 0x1C43D, 4, 0x00, 0x00, 0x00, 0x01, 2;
#Conner2-DAT   = 1, 0x2C,    0, 0x0DE39, 4, 0x00, 0x00, 0x00, 0x00, 0;
#DAT           = 1, 0x34,    0, 0x00439, 4, 0x00, 0x00, 0x00, 0x00, 0;
#DLT2          = 1, 0x38,    0, 0x0D639, 4, 0x17, 0x18, 0x80, 0x81, 2;
#DLT-data      = 1, 0x38,    0, 0x0D639, 4, 0x80, 0x81, 0x82, 0x83, 2;
#DLT7k-data    = 1, 0x38,    0, 0x0D639, 4, 0x82, 0x83, 0x84, 0x85, 2;
#EXB-2501      = 1, 0x28, 1024, 0x00442, 4, 0x00, 0x00, 0x00, 0x00, 0;
#EXB-8200      = 1, 0x28,    0, 0x08C79, 4, 0x00, 0x00, 0x00, 0x00, 0;
#EXB-850X      = 1, 0x29,    0, 0x0CE39, 4, 0x14, 0x15, 0x8C, 0x8C, 1;
#Exa4200c      = 1, 0x34,    0, 0x01639, 4, 0x63, 0x00, 0x00, 0x00, 1;
#Fujitsu_comp  = 1, 0x21,    0, 0x18639, 4, 0x00, 0x00, 0x00, 0x09, 1;
#Fujitsu_half  = 1, 0x21,    0, 0x0063B, 4, 0x00, 0x00, 0x00, 0x00, 0;
#Fujitsu_m248x = 1, 0x21,    0, 0x0C639, 4, 0x00, 0x00, 0x00, 0x00, 0;
#HP_DAT        = 1, 0x34,    0, 0x19679, 4, 0x00, 0x00, 0x00, 0x00, 0;
#HP_DAT_3      = 1, 0x34,    0, 0x09639, 4, 0x00, 0x8C, 0x8C, 0x8C, 1;
#HP_half       = 1, 0x23,    0, 0x0041D, 4, 0x01, 0x02, 0x03, 0xC3, 1;
#KENNEDY       = 1, 0x22,    0, 0x0041D, 4, 0x01, 0x02, 0x03, 0x03, 1;
#LMS           = 1, 0x20,    0, 0x0066B, 4, 0x00, 0x00, 0x00, 0x00, 0;
#M4_DATA       = 1, 0x27,    0, 0x0049D, 4, 0x01, 0x02, 0x06, 0x06, 1;
#MT02          = 1, 0x14,  512, 0x00202, 4, 0x84, 0x05, 0x05, 0x05, 1;
#MetD          = 1, 0x36,    0, 0x01639, 4, 0x00, 0x00, 0x00, 0x00, 0;
#NS20          = 1, 0x32,  512, 0x0C40A, 4, 0x00, 0x00, 0x00, 0x00, 0;
#QIC150        = 1, 0x15,  512, 0x00642, 4, 0x00, 0x00, 0x00, 0x00, 0;
#TANDB-2_5G    = 1, 0x32,    0, 0x0D67B, 4, 0x00, 0x00, 0x00, 0x00, 0;
#TAND-8G-VAR   = 1, 0x37,    0, 0x0963B, 4, 0xA0, 0xD0, 0xD0, 0xD0, 3;
#TANDBERG_MLR1 = 1, 0x32,  512, 0x0463A, 4, 0x00, 0x00, 0x00, 0x00, 0;
#TAND-50G-VAR  = 1, 0x37,    0, 0x0963B, 4, 0xA0, 0xD0, 0xD0, 0xD0, 3;
#TAND_4100_QIC = 1, 0x32,  512, 0x0463A, 4, 0x00, 0x00, 0x00, 0x00, 0;
#TAND_4200_QIC = 1, 0x32,  512, 0x0463A, 4, 0x00, 0x00, 0x00, 0x00, 0;
#WANGTEK_6130  = 1, 0x2A,    0, 0x00659, 4, 0x00, 0x00, 0x00, 0x00, 0;
#WANGTEK_QC150 = 1, 0x16,  512, 0x00642, 4, 0x00, 0x00, 0x00, 0x00, 0;
#WangDAT       = 1, 0x2B,    0, 0x00659, 4, 0x00, 0x00, 0x00, 0x00, 0;
#WangDAT       = 1, 0x34,    0, 0x00679, 4, 0x00, 0x00, 0x00, 0x00, 0;
#WtQIC         = 1, 0x32,  512, 0x0467A, 4, 0x00, 0x00, 0x00, 0x00, 0;
#CLASS_HP460 = 2, 0x3b, 0, 0x18659, 1, 0x42, 0x42, 0x42, 0x42, 0; 
#

name="st" class="scsi" target=0 lun=0;
name="st" class="scsi" target=1 lun=0;
name="st" class="scsi" target=2 lun=0;
name="st" class="scsi" target=3 lun=0;
name="st" class="scsi" target=4 lun=0;
name="st" class="scsi" target=5 lun=0;
name="st" class="scsi" target=6 lun=0;

#
#In case there are wide tape drives, one can use these targets
#
name="st" class="scsi" target=8 lun=0;
name="st" class="scsi" target=9 lun=0;
name="st" class="scsi" target=10 lun=0;
name="st" class="scsi" target=11 lun=0;
name="st" class="scsi" target=12 lun=0;
name="st" class="scsi" target=13 lun=0;
name="st" class="scsi" target=14 lun=0;
name="st" class="scsi" target=15 lun=0;

name="st" class="scsi" target=0 lun=1;
name="st" class="scsi" target=1 lun=1;
name="st" class="scsi" target=2 lun=1;
name="st" class="scsi" target=3 lun=1;
name="st" class="scsi" target=4 lun=1;
name="st" class="scsi" target=5 lun=1;
name="st" class="scsi" target=6 lun=1;
name="st" class="scsi" target=8 lun=1;
name="st" class="scsi" target=9 lun=1;
name="st" class="scsi" target=10 lun=1;
name="st" class="scsi" target=11 lun=1;
name="st" class="scsi" target=12 lun=1;
name="st" class="scsi" target=13 lun=1;
name="st" class="scsi" target=14 lun=1;
name="st" class="scsi" target=15 lun=1;

name="st" class="scsi" target=0 lun=2;
name="st" class="scsi" target=1 lun=2;
name="st" class="scsi" target=2 lun=2;
name="st" class="scsi" target=3 lun=2;
name="st" class="scsi" target=4 lun=2;
name="st" class="scsi" target=5 lun=2;
name="st" class="scsi" target=6 lun=2;
name="st" class="scsi" target=8 lun=2;
name="st" class="scsi" target=9 lun=2;
name="st" class="scsi" target=10 lun=2;
name="st" class="scsi" target=11 lun=2;
name="st" class="scsi" target=12 lun=2;
name="st" class="scsi" target=13 lun=2;
name="st" class="scsi" target=14 lun=2;
name="st" class="scsi" target=15 lun=2;

name="st" class="scsi" target=0 lun=3;
name="st" class="scsi" target=1 lun=3;
name="st" class="scsi" target=2 lun=3;
name="st" class="scsi" target=3 lun=3;
name="st" class="scsi" target=4 lun=3;
name="st" class="scsi" target=5 lun=3;
name="st" class="scsi" target=6 lun=3;
name="st" class="scsi" target=8 lun=3;
name="st" class="scsi" target=9 lun=3;
name="st" class="scsi" target=10 lun=3;
name="st" class="scsi" target=11 lun=3;
name="st" class="scsi" target=12 lun=3;
name="st" class="scsi" target=13 lun=3;
name="st" class="scsi" target=14 lun=3;
name="st" class="scsi" target=15 lun=3;

name="st" class="scsi" target=0 lun=4;
name="st" class="scsi" target=1 lun=4;
name="st" class="scsi" target=2 lun=4;
name="st" class="scsi" target=3 lun=4;
name="st" class="scsi" target=4 lun=4;
name="st" class="scsi" target=5 lun=4;
name="st" class="scsi" target=6 lun=4;
name="st" class="scsi" target=8 lun=4;
name="st" class="scsi" target=9 lun=4;
name="st" class="scsi" target=10 lun=4;
name="st" class="scsi" target=11 lun=4;
name="st" class="scsi" target=12 lun=4;
name="st" class="scsi" target=13 lun=4;
name="st" class="scsi" target=14 lun=4;
name="st" class="scsi" target=15 lun=4;

name="st" class="scsi" target=0 lun=5;
name="st" class="scsi" target=1 lun=5;
name="st" class="scsi" target=2 lun=5;
name="st" class="scsi" target=3 lun=5;
name="st" class="scsi" target=4 lun=5;
name="st" class="scsi" target=5 lun=5;
name="st" class="scsi" target=6 lun=5;
name="st" class="scsi" target=8 lun=5;
name="st" class="scsi" target=9 lun=5;
name="st" class="scsi" target=10 lun=5;
name="st" class="scsi" target=11 lun=5;
name="st" class="scsi" target=12 lun=5;
name="st" class="scsi" target=13 lun=5;
name="st" class="scsi" target=14 lun=5;
name="st" class="scsi" target=15 lun=5;

# This line adds support for Fibre Channel Tapes
name="st" parent="fp" target=0;
7. 重启主机：shutdown –i6 g0 –y，或通过使用下列命令配置磁带设备(可以不重启)
# update_drv –f st （使修改后的st.conf生效，仅对Solaris 9有效）
# modinfo | grep st （确认st被加载）
# modinfo | grep lpfc （确认lpfc被加载）
8. ls /dev/rmt （确认磁带机设备已经生成），如果没有，再执行一次devfsadm。
9. inquire （应该可以看到机械手和磁带库上的磁带机）
# inquire |grep Ultrium
scsidev@3.0.1:HP      Ultrium 2-SCSI  F49Z|Tape, /dev/rmt/0cbn
                                           ATNN:HP      Ultrium 2-SCSI  HUL3C00118
scsidev@3.0.2:HP      Ultrium 2-SCSI  F49Z|Tape, /dev/rmt/1cbn
                                           ATNN:HP      Ultrium 2-SCSI  HUL3C00096
scsidev@3.0.3:HP      Ultrium 2-SCSI  F49Z|Tape, /dev/rmt/2cbn
                                           ATNN:HP      Ultrium 2-SCSI  HUL3C00078
scsidev@3.0.4:HP      Ultrium 2-SCSI  F49Z|Tape, /dev/rmt/3cbn
                                           ATNN:HP      Ultrium 2-SCSI  HUL4C02062
10. 使用jbedit –a添加Storage Node。


如果有任何问题，欢迎大家一起讨论。