6506> (enable) show config
This command shows non-default configurations only.
Use 'show config all' to show both default and non-default config
.........
................
................
..............
..
begin
!
# ***** NON-DEFAULT CONFIGURATION *****
!
!
#time: Thu Jan 4 2001, 08:27:22
!
#version 5.4(3) #
软件版本
!
set
password $2$lnsk$mgJ84scE.A51hpr0Zbdfv/ #加密后的telnet
密码
set enablepass $2$RFAC$BDgIVKdk3gl1RD4.DaNcu. #加密后的enable密码
!
#system
set system name 6506 #
系统名称
!
#!
#vtp
set vtp domain _domain # VTP域名
set vtp passwd _password # VTP域密码
set vlan 1 name default type ethernet mtu 1500 said 100001 state #建立
VLAN
set vlan 2 name vlan2 type ethernet mtu 1500 said 100002 state act
set vlan 3 name valn3 type ethernet mtu 1500 said 100003 state acti
set vlan 1002 name fddi-default type fddi mtu 1500 said 101002 st
set vlan 1004 name fddinet-default type fddinet mtu 1500 said 101
e stp ieee
set vlan 1005 name trnet-default type trbrf mtu 1500 said 101005
p ibm
set vlan 1003 name token-ring-default type trcrf mtu 1500 said 10
ve mode srb aremaxhop 7 stemaxhop 7 backupcrf off
!
#ip
set interface sc0 1 10.1.1.253/255.255.255.0 10.1.1.255 #本
交换机的IP
地址
set ip route 0.0.0.0/0.0.0.0 10.1.1.254 #默认网关
set ip alias default 0.0.0.0 #
设置ip对应的
设备名，方便
管理
set ip alias 6506 10.1.1.253 #用途如：ping 2620, telnet 3548_2a
set ip alias msfc 10.1.1.254
set ip alias 4912 10.1.1.252
set ip alias 2620 10.1.8.250
...
!
#set boot command
set boot config-register 0x102 #启动寄存器值及启动文件
set boot system flash bootflash:cat6000-sup.5-4-3.bin
!
#mls
set mls flow full #多层交换流类型
!
#security ACLs #
访问列表
clear security
acl all
#server
set security acl ip server deny ip host 10.1.1.199 host 10.1.1.200
#
commit security acl all
!
# default port status is enable
!
!
#module 1 : 2-port 1000Ba*** Supervisor #管理引擎（含2口千兆模块）
!
#module 2 : 8-port 1000Ba*** Ethernet #8口千兆交换模块
set vlan 5 2/1 #指定
端口2/1到vlan 5
set port name 2/1 gg #设置端口名称
set port name 2/2 cb
set port name 2/3 server1
set port name 2/4 server2
set port name 2/5 3548_2a
set udld enable 2/6-8 #未安装GBIC时激活检测
set trunk 2/1 off dot1q 1-1005 #设置2/1为运行802.1Q
协议的干道，允许vlan 1-1005通过
set trunk 2/2 on dot1q 1-1005
set trunk 2/3 on dot1q 1-1005
set trunk 2/4 on dot1q 1-1005
set trunk 2/5 nonegotiate isl 1-1005
!
#module 3 : 8-port 1000Ba*** Ethernet #8口千兆交换模块
set port name 3/4 3524_17a
set port name 3/5 3548_9b
set port name 3/6 3548_9a
set port name 3/7 3548_f4a
set port name 3/8 3548_12a
set udld enable 3/1-3
set trunk 3/1 on dot1q 1-1005
set trunk 3/4 nonegotiate isl 1-1005 #设置3/4为运行isl协议的干道，允许vlan 1-1005通过
set trunk 3/5 nonegotiate isl 1-1005
set trunk 3/6 nonegotiate isl 1-1005
set trunk 3/7 nonegotiate isl 1-1005
set trunk 3/8 nonegotiate isl 1-1005
!
#module 4 empty
!
#module 5 empty
!
#module 6 empty
!
#module 15 : 1-port Multilayer Switch Feature Card
set port name 15/1 msfc #
路由、多层交换模块
!
#module 16 empty
end
