Chinaunix首页 | 论坛 | 博客
  • 博客访问: 2520041
  • 博文数量: 609
  • 博客积分: 10061
  • 博客等级: 上将
  • 技术积分: 5920
  • 用 户 组: 普通用户
  • 注册时间: 2008-06-25 08:30
文章分类

全部博文(609)

文章存档

2010年(13)

2009年(39)

2008年(558)

我的朋友

分类: LINUX

2008-08-29 18:48:55

Linux creating or adding new network alias to a network card (NIC)


Q. I would like to create alias for my network card (NIC). How do I setup 2 IP address on One NIC? How do I add alias?

A. Linux allows you to add additional network address using alias feature. Please note that all additional network IP address must be in same subnet. For example if your eth0 using 192.168.1.5 IP address then alias must be setup using 192.168.1.0/24 subnet.

You can use ifconfig command to configure a network interface and alias. For example:

    * eth0 NIC IP 192.168.1.5
    * eth0:0 first NIC alias: 192.168.1.6

To setup eth0:0 alias type the following command as the root user:
# ifconfig eth0:0 192.168.1.6 up
Verify alias is up and running using following command:
# ifconfig -a
# ping 192.168.1.6
However, if you reboot the system you will lost all your alias. To make it permanent you need to add it network configuration file.
Debian / Ubuntu Linux Instructions

You can configure the additional IP addresses automatically at boot with another iface statement in /etc/network/interfaces:
# vi /etc/network/interfaces
Append text as follows:

auto eth0:1
iface eth0:1 inet static
name Ethernet alias LAN card
address 192.168.1.7
netmask 255.255.255.0
broadcast 192.168.1.255
network 192.168.1.0

Save and close the file. Restart the network:
# /etc/init.d/networking restart

Red Hat / RHEL / CentOS / Fedora Linux Instructions

Copy etc/sysconfig/network-scripts/ifcfg-eth0 file as /etc/sysconfig/network-scripts/ifcfg-eth0:0
# cp /etc/sysconfig/network-scripts/ifcfg-eth0 /etc/sysconfig/network-scripts/ifcfg-eth0:0
Open file /etc/sysconfig/network-scripts/ifcfg-eth0:0 using vi text editor:
# vi /etc/sysconfig/network-scripts/ifcfg-eth0:0
Find entry that read as follows:

DEVICE=eth0

Replace with:

DEVICE=eth0:0

Find entry that read as follows:

IPADDR=xxx.xxx.xxx.xxx

Replace it with your actual IP address:

IPADDR=192.168.1.7

At the end your file should like as follows:

DEVICE=eth0:0
IPADDR=192.168.1.7
NETMASK=255.255.255.0
NETWORK=192.168.1.0
ONBOOT=yes
NAME=eth0:0

Open file /etc/sysconfig/network-scripts/ifcfg-eth0 and make sure file does not have a GATEWAY= entry:
# vi /etc/sysconfig/network-scripts/ifcfg-eth0
Find the entry that read as follows:

GATEWAY=your-ip

Remove or comment it out by prefixing # (hash) :

 # GATEWAY=192.168.1.254

Save the file. Add the GATEWAY= to your /etc/sysconfig/network:

# vi /etc/sysconfig/network

Append or modify GATEWAY entry:

GATEWAY=192.168.1.254

Save the file. Reboot the system or run the following command:

# ifup eth0:0

OR

# service network restart

Red Hat / CentOS / Fedora Multiple IP address range

You can assign multiple ip address range as follows to eth0:
vi /etc/sysconfig/network-scripts/ifcfg-eth0-range0
Append following code from 202.54.112.120 to 202.54.112.140:

IPADDR_START=202.54.112.120
IPADDR_END=202.54.112.140
CLONENUM_START=0
NETMASK=255.255.255.0

Save and close the file.
阅读(1101) | 评论(0) | 转发(0) |
给主人留下些什么吧!~~