全部博文（108）
分类： LINUX
2007-04-19 22:53:42
For rt73, please add ASUS IDs (red words) in the rtmp_def.h.
#define RT73_USB_DEVICES { \
{USB_DEVICE(0x148f,0x2573)}, /* Ralink */ \
{USB_DEVICE(0x0B05,0x1723)}, /* ASUS */ \#mv /home/crowtlf/Desktop/RT73_Linux_STA_Drv1.0.3.6/ /usr/src/linux-headers-2.6.18-4/drivers/net/
#chmod -R 777 RT73_Linux_STA_Drv1.0.3.6/
#vim rtmp_def.h
#vim ifcfg-rausb0
1> $tar -xvzf RT73_Linux_STA_Drv_x.x.x.x.tar.gz
go to "./RT73_Linux_STA_Drv_x.x.x.x/Module" directory.
2> $cp Makefile.4 ./Makefile # [kernel 2.4]
or
$cp Makefile.6 ./Makefile # [kernel 2.6]
3> [kernel 2.4]
$chmod 755 Configure
$make config # config build linux os version
4> $make all # compile driver source code
5> $cp rt73.bin /etc/Wireless/RT73STA/ # copy firmware
目录要一级级的自己建立
6> $dos2unix rt73sta.dat
$cp rt73sta.dat /etc/Wireless/RT73STA/rt73sta.dat
# !!!check if it is a binary file before loading !!!
7> $load
#[kernel 2.4]
# $/sbin/insmod rt73.o
# $/sbin/ifconfig rausb0 inet YOUR_IP up
#[kernel 2.6]
# $/sbin/insmod rt73.ko
# $/sbin/ifconfig rausb0 inet YOUR_IP up
=======================================================================
CONFIGURATION:
====================
RT73 driver can be configured via following interfaces,
i.e. (i)"iwconfig" command, (ii)"iwpriv" command, (iii) configuration file
(iv)RaConfig
i) iwconfig comes with kernel.
ii) iwpriv usage, please refer to file "iwpriv_usage.txt" for details.
iii)copy configuration file "rt73sta.dat" to /etc/Wireless/RT73STA/rt73sta.dat.
iv) RaConfig is utility for rt73.
Note:
Configuration File : rt73sta.dat
---------------------------------------
# Copy this file to /etc/Wireless/RT73STA/rt73sta.dat
# This file is a binary file and will be read on loading rt.o module.
#
# Use "vi -b rt73sta.dat" to modify settings according to your need.
#
# 1.) set NetworkType to "Adhoc" for using Adhoc-mode, otherwise using Infrastructure
# 2.) set Channel to "0" for auto-select on Infrastructure mode
# 3.) set SSID for connecting to your Accss-point.
# 4.) AuthMode can be "WEPAUTO", "OPEN", "SHARED", "WPAPSK", "WPA2PSK", "WPANONE"
# 5.) EncrypType can be "NONE", "WEP", "TKIP", "AES"
# for more information refer to the Readme file.
#
# The word of "[Default]" must not be removed
[Default]
CountryRegion=0
CountryRegionABand=7
WirelessMode=0
SSID=AP350
NetworkType=Infra
Channel=0
AuthMode=OPEN
EncrypType=NONE
DefaultKeyID=1
Key1Type=0
Key1Str=0123456789
Key2Type=0
Key2Str=
Key3Type=0
Key3Str=
Key4Type=0
Key4Str=
WPAPSK=abcdefghijklmnopqrstuvwxyz
TxBurst=0
PktAggregate=0
TurboRate=0
WmmCapable=0
AckPolicy=0;0;0;0
BGProtection=0
IEEE80211H=0
TxRate=0
RTSThreshold=2347
FragThreshold=2346
PSMode=CAM
TxPreamble=0
AdhocOfdm=0
FastRoaming=0
RoamThreshold=70
-----------------------------------------------
syntax is 'Param'='Value' and describes below.
1. CountryRegion=value
value
0: use 1 ~ 11 Channel
1: use 1 ~ 13 Channel
2: use 10, 11 Channel
3: use 10 ~ 13 Channel
4: use 14 Channel
5: use 1 ~ 14 Channel
6: use 3 ~ 9 Channel
7: use 5 ~ 13 Channel
2. CountryRegionABand=value
value
0: use 36, 40, 44, 48, 52, 56, 60, 64, 149, 153, 157, 161, 165 Channel
1: use 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140 Channel
2: use 36, 40, 44, 48, 52, 56, 60, 64 Channel
3: use 52, 56, 60, 64, 149, 153, 157, 161 Channel
4: use 149, 153, 157, 161, 165 Channel
5: use 149, 153, 157, 161 Channel
6: use 36, 40, 44, 48 Channel
7: use 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140, 149, 153, 157, 161, 165 Channel
8: use 52, 56, 60, 64 Channel
9: use 34, 38, 42, 46 Channel
10: use 34, 36, 38, 40, 42, 44, 46, 48, 52, 56, 60, 64 Channel
3. SSID=value
value
0~z, 1~32 ascii characters.
4. WirelessMode=value
value
0: 11b/g mixed,
1: 11b only,
2: 11a only, //Support in RfIcType=1(id=RFIC_5226) or RfIcType=3(id=RFIC_5225)
3: 11a/b/g mixed, //Support in RfIcType=1(id=RFIC_5226) or RfIcType=3(id=RFIC_5225)
4: 11g only
5. TxRate=value
value
0: Auto //WirelessMode=0~4
1: 1 Mbps //WirelessMode=0 or 1 or 3
2: 2 Mbps //WirelessMode=0 or 1 or 3
3: 5.5 Mbps //WirelessMode=0 or 1 or 3
4: 11 Mbps //WirelessMode=0 or 1 or 3
5: 6 Mbps //WirelessMode=0 or 2 or 3 or 4
6: 9 Mbps //WirelessMode=0 or 2 or 3 or 4
7: 12 Mbps //WirelessMode=0 or 2 or 3 or 4
8: 18 Mbps //WirelessMode=0 or 2 or 3 or 4
9: 24 Mbps //WirelessMode=0 or 2 or 3 or 4
10: 36 Mbps //WirelessMode=0 or 2 or 3 or 4
11: 48 Mbps //WirelessMode=0 or 2 or 3 or 4
12: 54 Mbps //WirelessMode=0 or 2 or 3 or 4
6. Channel=value
value
depends on CountryRegion or CountryRegionABand
7. BGProtection=value
value
0: Auto
1: Always on
2: Always off
8. TxPreamble=value
value
0: Preamble Long
1: Preamble Short
2: Auto
9. RTSThreshold=value
value
1~2347
10. FragThreshold=value
value
256~2346
11. TxBurst=value
value
0: Disable
1: Enable
12. NetworkType=value
value
Infra: infrastructure mode
Adhoc: adhoc mode
13. AdhocOfdm=value
value
0: WIFI mode (1,2,5.5,11 mbps rates)
1: b/g mixed, (1,2,5.5,11,6,9,12,18,24,36,48,54 mbps rates)
2: 11g only, (6,9,12,18,24,36,48,54 mbps rates)
3: 11a only, (6,9,12,18,24,36,48,54 mbps rates)
14. AuthMode=value
value
OPEN For open system
SHARED For shared key system
WEPAUTO Auto switch between OPEN and SHARED
WPAPSK For WPA pre-shared key (Infra)
WPA2PSK For WPA2 pre-shared key (Infra)
WPANONE For WPA pre-shared key (Adhoc)
WPA Use WPA-Supplicant
WPA2 Use WPA-Supplicant
15. EncrypType=value
value
NONE For AuthMode=OPEN
WEP For AuthMode=OPEN or SHARED
TKIP For AuthMode=WPAPSK or WPA2PSK or WPANONE
AES For AuthMode=WPAPSK or WPA2PSK or WPANONE
16. DefaultKeyID=value
value
1~4
17. Key1=value
Key2=value
Key3=value
Key4=value
value
10 or 26 hexadecimal characters eg: 012345678
5 or 13 ascii characters eg: passd
(usage : "iwpriv" only)
18. Key1Type=vaule
Key2Type=value
Key3Type=vaule
Key4Type=vaule
value
0 hexadecimal type
1 assic type
(usage : reading profile only)
19. Key1Str=value
Key2Str=value
Key3Str=vaule
Key4Str=vaule
value
10 or 26 characters (key type=0)
5 or 13 characters (key type=1)
(usage : reading profile only)
20. WPAPSK=value
value
8~63 ASCII or
64 HEX characters
21. PSMode=value
value
0: CAM Constantly Awake Mode
1: Max_PSP Max Power Savings
2: Fast_PSP Power Save Mode
22. IEEE80211H=value
value
0: Disable
1: Enable Spectrum management
(This field can be enable only in A band)
23. FastRoaming=value
value
0: Disable
1: Enable Fast Roaming
24. RoamThreshold=value
vale
61 ~ 89
This value is a absolute threshold in dBm.
The condition to roam when receiving Rssi less than (-1*value).
// //////////////////////
// No Support !!!
// /////////////////////
// PktAggregate,
// TurboRate,
// WmmCapable,
// AckPolicy
// /////////////////////
MORE INFORMATION
=================================================================================
If you want for rt73 driver to auto-load at boot time:
A) choose rausb0 for first RT73 WLAN card, rausb1 for second RT73 WLAN card, etc.
B) create(edit) 'ifcfg-rausb0' file in /etc/sysconfig/network-scripts/,
edit( or add the line) in /etc/modules.conf:
alias rausb0 rt73
C) edit(create) the file /etc/sysconfig/network-scripts/ifcfg-rausb0
DEVICE='rausb0'
ONBOOT='yes'
NOTE:
if you use dhcp, add this line too .
BOOTPROTO='dhcp'
*D) To ease the Default Gateway setting,
add the line
GATEWAY=x.x.x.x
in /etc/sysconfig/network
