Chinaunix首页 | 论坛 | 博客
  • 博客访问: 2301757
  • 博文数量: 141
  • 博客积分: 3552
  • 博客等级: 中校
  • 技术积分: 4148
  • 用 户 组: 普通用户
  • 注册时间: 2009-07-15 14:39
个人简介

熟悉Linux下程序设计及各种应用程序 熟悉C Language 熟悉Glusterfs、FFmpeg、CDN 系统设计,计算机图形系统设计、分布式程序设计 目前主要研究方向:流媒体

文章分类

全部博文(141)

分类: LINUX

2009-11-05 16:35:30

在安装完VirtualBox中的Linux以后,网络默认是NAT的
在看过帮助手册以后,发现可以使用NAT的形式登录进VirTualBox中的linux


6.4.1. Configuring port forwarding with NAT As the virtual machine is connected to a private network internal to VirtualBox and invisible to the host, network services on the guest are not accessible to the host machine or to other computers on the same network. However, VirtualBox can make selected services available outside of the guest by using port forwarding. This means that VirtualBox listens to certain ports on the host and resends all packets which arrive on them to the guest on the ports used by the services being forwarded. To an application on the host or other physical (or virtual) machines on the network, it looks as though the service being proxied is actually running on the host (note that this also means that you cannot run the same service on the same ports on the host). However, you still gain the advantages of running the service in a virtual machine -- for example, services on the host machine or on other virtual machines cannot be compromised or crashed by a vulnerability or a bug in the service, and the service can run in a different operating system than the host system. You can set up a guest service which you wish to proxy using the command line tool VBoxManage. You will need to know which ports on the guest the service uses and to decide which ports to use on the host (often but not always you will want to use the same ports on the guest and on the host). You can use any ports on the host which are not already in use by a service. An example of how to set up incoming NAT connections to an ssh server on the guest requires the following three commands: VBoxManage setextradata "Linux Guest" "VBoxInternal/Devices/pcnet/0/LUN#0/Config/guestssh/Protocol" TCP VBoxManage setextradata "Linux Guest" "VBoxInternal/Devices/pcnet/0/LUN#0/Config/guestssh/GuestPort" 22 VBoxManage setextradata "Linux Guest" "VBoxInternal/Devices/pcnet/0/LUN#0/Config/guestssh/HostPort" 2222 The above example assumes a PCNet virtual network card; if you have configured the guest to use the Intel PRO/1000, replace "pcnet" with "e1000" in the above commands. Similarly, if you want to configure a different interface instance replace the /0/ with the appropriate index. pcnet and e1000 are counted separately in this respect, and counting starts at 0 for both types. The name guestssh is an arbitrary one chosen for this particular forwarding configuration. With that configuration in place, all TCP connections to port 2222 on the host will be forwarded to port 22 on the guest. Protocol can be either of TCP or UDP (these are case insensitive). To remove a mapping again, use the same commands, but leaving out the values (in this case TCP, 22 and 2222). It is not possible to configure incoming NAT connections while the VM is running. However you can change the settings for a VM which is currently saved (or powered off at a snapshot).


设置完成以后,直接就可以ssh hostip -p 2222就可以登录进VirtualBox中的Linux了
阅读(3188) | 评论(0) | 转发(0) |
给主人留下些什么吧!~~