分类： 系统运维
2011-08-06 20:27:41
（1）查看核心交换机65-2的IOS版本信息：
switch-2#show version
Cisco IOS Software, s72033_rp Software (s72033_rp-IPBASE-VM), Version 12.2(33)SXH7, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Thu 11-Mar-10 15:13 by prod_rel_team
ROM: System Bootstrap, Version 12.2(17r)SX7, RELEASE SOFTWARE (fc1)
switch-2 uptime is 15 minutes
Uptime for this control processor is 14 minutes
Time since switch-2 switched to active is 14 minutes
System returned to ROM by reload at 03:09:48 UTC Thu Dec 9 2010 (SP by reload)
System image file is "sup-bootdisk:s72033-ipbase-vz.122-33.SXH7.bin"
cisco WS-C6506-E (R7000) processor (revision 1.2) with 1040384K/8192K bytes of memory.
Processor board ID SAL1441W13F
SR71000 CPU at 600Mhz, Implementation 1284, Rev 1.2, 512KB L2 Cache
Last reset from s/w reset
1 Virtual Ethernet interface
99 Gigabit Ethernet interfaces
2 Ten Gigabit Ethernet interfaces
1917K bytes of non-volatile configuration memory.
65536K bytes of Flash internal SIMM (Sector size 512K).
Configuration register is 0x2102
Patching is not available since the system is not running from an installed image. To install please use the "install file" command
switch-2#
说明：核心交换机65-2的IOS版本为Cisco IOS Release 12.2(33)SXH7，符合VSS实施要求。
（2）查看核心交换机65-2的模块信息：
switch-2#show module
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
1 48 CEF720 48 port 1000mb SFP WS-X6748-SFP XXXXXX
2 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX XXXXXX
5 5 Supervisor Engine 720 10GE (Active) VS-S720-10G XXXXXX
Mod MAC addresses Hw Fw Sw Status
--- ---------------------------------- ------ ------------ ------------ -------
1 588d.097c.a874 to 588d.097c.a8a3 2.4 12.2(18r)S1 12.2(33)SXH7 Ok
2 f866.f2eb.19f0 to f866.f2eb.1a1f 3.4 12.2(18r)S1 12.2(33)SXH7 Ok
5 c47d.4ffe.4090 to c47d.4ffe.4097 3.2 8.5(4) 12.2(33)SXH7 Ok
Mod Sub-Module Model Serial Hw Status
---- --------------------------- ------------------ ----------- ------- -------
1 Centralized Forwarding Card WS-F6700-CFC XXXXXX 4.1 Ok
2 Centralized Forwarding Card WS-F6700-CFC XXXXXX 4.1 Ok
5 Policy Feature Card 3 VS-F6K-PFC3C XXXXXX 1.1 Ok
5 MSFC3 Daughterboard VS-F6K-MSFC3 XXXXXX 5.1 Ok
Mod Online Diag Status
---- -------------------
1 Pass
2 Pass
5 Pass
switch-2#
说明：核心交换机65-2的引擎为VS-S720-10G，安装于第5个插糟中，业务板卡WS-X6748-SFP和WS-X6748-GE-TX分别安装于第1个插糟和第2个插糟。
（3）查看核心交换机65-2的配置信息：
switch-2#show running-config
Building configuration...
Current configuration : 7243 bytes
!
upgrade fpd auto
version 12.2
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
service counters max age 5
!
hostname switch-2
!
boot-start-marker
boot-end-marker
!
!
no aaa new-model
ip subnet-zero
!
!
!
call-home
alert-group configuration
alert-group diagnostic
alert-group environment
alert-group inventory
alert-group syslog
profile "CiscoTAC-1"
no active
no destination transport-method http
destination transport-method email
destination address email callhome@cisco.com
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
subscribe-to-alert-group diagnostic severity minor
subscribe-to-alert-group environment severity minor
subscribe-to-alert-group syslog severity major pattern ".*"
subscribe-to-alert-group configuration periodic monthly 12 12:38
subscribe-to-alert-group inventory periodic monthly 12 12:23
mls netflow interface
no mls flow ip
no mls flow ipv6
mls cef error action reset
fabric timer 15
diagnostic cns publish cisco.cns.device.diag_results
diagnostic cns subscribe cisco.cns.device.diag_commands
!
redundancy
keepalive-enable
mode sso
main-cpu
auto-sync running-config
spanning-tree mode pvst
spanning-tree extend system-id
!
!
!
vlan internal allocation policy ascending
vlan access-log ratelimit 2000
!
!
interface GigabitEthernet1/1
no ip address
shutdown
!
interface GigabitEthernet1/2
no ip address
shutdown
!
interface GigabitEthernet1/3
no ip address
shutdown
!
interface GigabitEthernet1/4
no ip address
shutdown
!
interface GigabitEthernet1/5
no ip address
shutdown
!
interface GigabitEthernet1/6
no ip address
shutdown
!
interface GigabitEthernet1/7
no ip address
shutdown
!
interface GigabitEthernet1/8
no ip address
shutdown
!
interface GigabitEthernet1/9
no ip address
shutdown
!
interface GigabitEthernet1/10
no ip address
shutdown
!
interface GigabitEthernet1/11
no ip address
shutdown
!
interface GigabitEthernet1/12
no ip address
shutdown
!
interface GigabitEthernet1/13
no ip address
shutdown
!
interface GigabitEthernet1/14
no ip address
shutdown
!
interface GigabitEthernet1/15
no ip address
shutdown
!
interface GigabitEthernet1/16
no ip address
shutdown
!
interface GigabitEthernet1/17
no ip address
shutdown
!
interface GigabitEthernet1/18
no ip address
shutdown
!
interface GigabitEthernet1/19
no ip address
shutdown
!
interface GigabitEthernet1/20
no ip address
shutdown
!
interface GigabitEthernet1/21
no ip address
shutdown
!
interface GigabitEthernet1/22
no ip address
shutdown
!
interface GigabitEthernet1/23
no ip address
shutdown
!
interface GigabitEthernet1/24
no ip address
shutdown
!
interface GigabitEthernet1/25
no ip address
shutdown
!
interface GigabitEthernet1/26
no ip address
shutdown
!
interface GigabitEthernet1/27
no ip address
shutdown
!
interface GigabitEthernet1/28
no ip address
shutdown
!
interface GigabitEthernet1/29
no ip address
shutdown
!
interface GigabitEthernet1/30
no ip address
shutdown
!
interface GigabitEthernet1/31
no ip address
shutdown
!
interface GigabitEthernet1/32
no ip address
shutdown
!
interface GigabitEthernet1/33
no ip address
shutdown
!
interface GigabitEthernet1/34
no ip address
shutdown
!
interface GigabitEthernet1/35
no ip address
shutdown
!
interface GigabitEthernet1/36
no ip address
shutdown
!
interface GigabitEthernet1/37
no ip address
shutdown
!
interface GigabitEthernet1/38
no ip address
shutdown
!
interface GigabitEthernet1/39
no ip address
shutdown
!
interface GigabitEthernet1/40
no ip address
shutdown
!
interface GigabitEthernet1/41
no ip address
shutdown
!
interface GigabitEthernet1/42
no ip address
shutdown
!
interface GigabitEthernet1/43
no ip address
shutdown
!
interface GigabitEthernet1/44
no ip address
shutdown
!
interface GigabitEthernet1/45
no ip address
shutdown
!
interface GigabitEthernet1/46
no ip address
shutdown
!
interface GigabitEthernet1/47
no ip address
shutdown
!
interface GigabitEthernet1/48
no ip address
shutdown
!
interface GigabitEthernet2/1
no ip address
shutdown
!
interface GigabitEthernet2/2
no ip address
shutdown
!
interface GigabitEthernet2/3
no ip address
shutdown
!
interface GigabitEthernet2/4
no ip address
shutdown
!
interface GigabitEthernet2/5
no ip address
shutdown
!
interface GigabitEthernet2/6
no ip address
shutdown
!
interface GigabitEthernet2/7
no ip address
shutdown
!
interface GigabitEthernet2/8
no ip address
shutdown
!
interface GigabitEthernet2/9
no ip address
shutdown
!
interface GigabitEthernet2/10
no ip address
shutdown
!
interface GigabitEthernet2/11
no ip address
shutdown
!
interface GigabitEthernet2/12
no ip address
shutdown
!
interface GigabitEthernet2/13
no ip address
shutdown
!
interface GigabitEthernet2/14
no ip address
shutdown
!
interface GigabitEthernet2/15
no ip address
shutdown
!
interface GigabitEthernet2/16
no ip address
shutdown
!
interface GigabitEthernet2/17
no ip address
shutdown
!
interface GigabitEthernet2/18
no ip address
shutdown
!
interface GigabitEthernet2/19
no ip address
shutdown
!
interface GigabitEthernet2/20
no ip address
shutdown
!
interface GigabitEthernet2/21
no ip address
shutdown
!
interface GigabitEthernet2/22
no ip address
shutdown
!
interface GigabitEthernet2/23
no ip address
shutdown
!
interface GigabitEthernet2/24
no ip address
shutdown
!
interface GigabitEthernet2/25
no ip address
shutdown
!
interface GigabitEthernet2/26
no ip address
shutdown
!
interface GigabitEthernet2/27
no ip address
shutdown
!
interface GigabitEthernet2/28
no ip address
shutdown
!
interface GigabitEthernet2/29
no ip address
shutdown
!
interface GigabitEthernet2/30
no ip address
shutdown
!
interface GigabitEthernet2/31
no ip address
shutdown
!
interface GigabitEthernet2/32
no ip address
shutdown
!
interface GigabitEthernet2/33
no ip address
shutdown
!
interface GigabitEthernet2/34
no ip address
shutdown
!
interface GigabitEthernet2/35
no ip address
shutdown
!
interface GigabitEthernet2/36
no ip address
shutdown
!
interface GigabitEthernet2/37
no ip address
shutdown
!
interface GigabitEthernet2/38
no ip address
shutdown
!
interface GigabitEthernet2/39
no ip address
shutdown
!
interface GigabitEthernet2/40
no ip address
shutdown
!
interface GigabitEthernet2/41
no ip address
shutdown
!
interface GigabitEthernet2/42
no ip address
shutdown
!
interface GigabitEthernet2/43
no ip address
shutdown
!
interface GigabitEthernet2/44
no ip address
shutdown
!
interface GigabitEthernet2/45
no ip address
shutdown
!
interface GigabitEthernet2/46
no ip address
shutdown
!
interface GigabitEthernet2/47
no ip address
shutdown
!
interface GigabitEthernet2/48
no ip address
shutdown
!
interface GigabitEthernet5/1
no ip address
shutdown
!
interface GigabitEthernet5/2
no ip address
shutdown
!
interface GigabitEthernet5/3
no ip address
shutdown
!
interface TenGigabitEthernet5/4
no ip address
shutdown
!
interface TenGigabitEthernet5/5
no ip address
shutdown
!
interface Vlan1
no ip address
shutdown
!
ip classless
!
!
no ip http server
!
!
control-plane
!
!
line con 0
line vty 0 4
!
exception core-file
!
end
switch-2#
说明：从配 置文件中可以看出核心交换机65-2上的接口均正常显示，GigabitEthernet1/2为业务板卡WS-X6748-SFP上的接 口，GigabitEthernet2/3为业务板卡WS-X6748-GE-TX上的接口，TenGigabitEthernet5/4为引擎VS- S720-10G上的10 Gigabit 光模块接口。
还需要注意的是，此IOS版本中已经默认配置了SSO，所以在配置VSS时，不再需要配置SSO。
3．在核心交换机65-1上配置VSS
说明：由于目前的IOS版本中已经默认配置了SSO，所以在配置VSS时，不再需要配置SSO。
（1）查看核心交换机65-1当前的工作模式：
switch-1#show switch virtual
Switch Mode : Standalone
switch-1#
说明：核心交换机65-1当前的工作模式为Standalone，即为单机模式，而非VSS模式。
（2）将核心交换机65-1上与65-2相连的接口TenGigabitEthernet5/4和TenGigabitEthernet5/5配置为EtherChannel：
switch-1(config)#interface range tenGigabitEthernet 5/4 - 5
switch-1(config-if-range)#channel-group 10 mode on
switch-1(config-if-range)#no shutdown
% Range command terminated because it failed on TenGigabitEthernet5/4
switch-1(config-if-range)#exit
说明：将核心交换机65-1上与65-2相连的接口TenGigabitEthernet5/4和TenGigabitEthernet5/5配置为EtherChannel，为配置VSL作准备。
（3）配置VSS域名与VSS主机号：
switch-1(config)#switch virtual domain 100
Domain ID 100 config will take effect only
after the exec command 'switch convert mode virtual' is issued
switch-1(config-vs-domain)#switch 1
switch-1(config-vs-domain)#switch 1 priority 200
switch-1(config-vs-domain)#switch 1 preempt
Please note that Preempt configuration will make the ACTIVE switch with lower priority to reload forcefully when preempt timer expires
switch-1(config-vs-domain)#exit
说明：配置VSS的域名为100，范围为1-255，两台交换机必须相同；配置VSS的主机号码为1，必须一台为1，另一台为2；并配置VSS优先级为200，默认为100，数字越大，优先级越高，便能成为主VSS交换机。
（4）配置VSL链路：
switch-1(config)#interface port-channel 10
switch-1(config-if)#switch virtual link 1
switch-1(config-if)#no shutdown
switch-1(config-if)#exit
switch-1(config)#exit
说明：将两台交换机互连的EtherChannel配置为VSL。
（5）将交换机的工作模式改为VSS模式（确定之后，交换机将自动重启）：
switch-1#write
Building configuration...
[OK]
switch-1#
switch-1#switch convert mode virtual
This command will convert all interface names
to naming convention "interface-type switch-number/slot/port",
save the running config to startup-config and
reload the switch.
Do you want to proceed? [yes/no]: y
Converting interface names
Building configuration...
[OK]
Saving converted configuration to bootflash: ...
Destination filename [startup-config.converted_vs-20101209-032047]?
?
00:09:39: %SYS-SP-3-LOGGER_FLUSHING: System pausing to ensure console debugging output.
00:09:39: %OIR-SP-6-CONSOLE: Changing console ownership to switch processor
00:09:39: %SYS-SP-3-LOGGER_FLUSHED: System was paused for 00:00:00 to ensure console debugging output.
00:09:41: %SYS-SP-3-LOGGER_FLUSHING: System pausing to ensure console debugging output.
***
*** --- SHUTDOWN NOW ---
***
00:09:41: %SYS-SP-5-RELOAD: Reload requested
00:09:41: %OIR-SP-6-CONSOLE: Changing console ownership to switch processor
00:09:41: %SYS-SP-3-LOGGER_FLUSHED: System was paused for 00:00:00 to ensure console debugging output.
System Bootstrap, Version 8.5(3)
Copyright (c) 1994-2008 by cisco Systems, Inc.
Cat6k-Sup720/SP processor with 1048576 Kbytes of main memory
Autoboot: failed, BOOT string is empty
Autoboot executing command: "boot "
Initializing ATA monitor library...
string is bootdisk:s72033-ipbase-vz.122-33.SXH7.bin
Loading image, please wait ...
Initializing ATA monitor library...
Self extracting the image... [OK]
Self decompressing the image :
###############################################################################
###############################################################################
###############################################################################
################################################################# [OK]
running startup....
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, s72033_sp Software (s72033_sp-IPBASE-VM), Version 12.2(33)SXH7, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Thu 11-Mar-10 15:46 by prod_rel_team
Image text-base: 0x01020150, data-base: 0x01021000
System detected Virtual Switch configuration...
Interface TenGigabitEthernet 1/5/4 is member of PortChannel 10
Interface TenGigabitEthernet 1/5/5 is member of PortChannel 10
00:00:21: %SYS-3-LOGGER_FLUSHING: System pausing to ensure console debugging output.
Firmware compiled 12-Jan-10 13:19 by integ Build [100]
Earl Card Index= 259
00:00:21: %PFREDUN-6-ACTIVE: Initializing as ACTIVE processor for this switch
Initializing as Virtual Switch ACTIVE processor
00:01:58: %SYS-3-LOGGER_FLUSHING: System pausing to ensure console debugging output.
00:00:21: %SYS-3-LOGGER_FLUSHED: System was paused for 00:00:00 to ensure console debugging output.
00:00:26: %VSL_BRINGUP-6-MODULE_UP: VSL module in slot 5 switch 1 brought up
00:01:58: %VSLP-5-RRP_PEER_TIMEOUT: VSLP peer timer expired without detecting peer. Resolving role as Active
00:01:58: %VSLP-2-VSL_DOWN: VSL links down and not ready for any traffic
00:01:58: %OIR-6-CONSOLE: Changing console ownership to route processor
System Bootstrap, Version 12.2(17r)SX6, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2009 by cisco Systems, Inc.
Cat6k-Sup720/RP platform with 1048576 Kbytes of main memory
Download Start
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Download Completed! Booting the image.
Self decompressing the image :
###############################################################################
###############################################################################
###############################################################################
###############################################################################
###############################################################################
################################ [OK]
running startup....
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, s72033_rp Software (s72033_rp-IPBASE-VM), Version 12.2(33)SXH7, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Thu 11-Mar-10 15:13 by prod_rel_team
Image text-base: 0x01020150, data-base: 0x01021000
cisco WS-C6506-E (R7000) processor (revision 1.2) with 1040384K/8192K bytes of memory.
Processor board ID SAL1412DQ6Y
SR71000 CPU at 600Mhz, Implementation 1284, Rev 1.2, 512KB L2 Cache
Last reset from s/w reset
1 Virtual Ethernet interface
99 Gigabit Ethernet interfaces
2 Ten Gigabit Ethernet interfaces
1917K bytes of non-volatile configuration memory.
65536K bytes of Flash internal SIMM (Sector size 512K).
fabric timer 15
^
% Invalid input detected at '^' marker.
Press RETURN to get started!
00:00:49: curr is 0x0
00:00:49: RP: Currently running ROMMON from S (Gold) region
00:00:50: %SPANTREE-5-EXTENDED_SYSID: Extended SysId enabled for type vlan. The Bridge IDs of all active STP instances have been updated, which might change the spanning tree topology
00:00:55: %SYS-5-CONFIG_I: Configured from memory by console
00:00:58: %SYS-5-RESTART: System restarted --
Cisco IOS Software, s72033_rp Software (s72033_rp-IPBASE-VM), Version 12.2(33)SXH7, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Thu 11-Mar-10 15:13 by prod_rel_team
00:01:58: %SYS-3-LOGGER_FLUSHED: System was paused for 00:00:00 to ensure console debugging output.
00:03:30: %SPANTREE-SW1_SP-5-EXTENDED_SYSID: Extended SysId enabled for type vlan. The Bridge IDs of all active STP instances have been updated, which might change the spanning tree topology
switch-1> SW1_SP: SP: Currently running ROMMON from S (Gold) region
switch-1>
switch-1>
00:03:44: %SYS-SW1_SP-5-RESTART: System restarted --
Cisco IOS Software, s72033_sp Software (s72033_sp-IPBASE-VM), Version 12.2(33)SXH7, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Thu 11-Mar-10 15:46 by prod_rel_team
00:03:45: %SYS-SW1_SP-6-BOOTTIME: Time taken to reboot after reload = 309 seconds
00:03:45: %OIR-SW1_SP-6-INSPS: Power supply inserted in slot 1
00:03:45: %C6KPWR-SW1_SP-4-PSOK: power supply 1 turned on.
00:03:45: %OIR-SW1_SP-6-INSPS: Power supply inserted in slot 2
00:01:00: c6k_pwr_is_fantray_ok returns ok for fan_index 1
00:01:00: c6k_pwr_is_fantray_ok returns ok for fan_index 3
00:03:47: SW1_SP: Remote Switch 1 Physical Slot 5 - Module Type LINE_CARD inserted
00:03:47: %FABRIC-SW1_SP-5-CLEAR_BLOCK: Clear block option is off for the fabric in slot 5.
00:03:47: %FABRIC-SW1_SP-5-FABRIC_MODULE_ACTIVE: The Switch Fabric Module in slot 5 became active.
00:03:48: %DI
switch-1>
switch-1>
switch-1>AG-SW1_SP-6-RUN_MINIMUM: Switch 1 Module 5: Running Minimal Diagnostics...
00:03:49: SW1_SP: Remote Switch 1 Physical Slot 1 - Module Type LINE_CARD inserted
00:03:49: SW1_SP: Remote Switch 1 Physical Slot 2 - Module Type LINE_CARD inserted
switch-1>
switch-1>
switch-1>
switch-1>
switch-1>
switch-1>
switch-1>
switch-1>
switch-1>enable
switch-1#
说明：当将交换机的工作模式从单机改为VSS模式之后，交换机会自动重启。
（6）再次查看当前交换机的工作模式：
switch-1#show switch virtual
Switch mode : Virtual Switch
Virtual switch domain number : 100
Local switch number : 1
Local switch operational role: Virtual Switch Active
switch-1#
说明：交换机当前已经工作在VSS模式，并显示域名为100，本地交换机号码为1，本地交换机的角色为Active，即具有控制权限的主交换机。
（7）查看当前交换机的VSS角色：
switch-1#show switch virtual role
Switch Switch Status Preempt Priority Role Session ID
Number Oper(Conf) Oper(Conf) Local Remote
------------------------------------------------------------------
LOCAL 1 UP TRUE (Y*) 200(200) ACTIVE 0 0
Active configured preempt timer(switch 1): 5 minutes
In dual-active recovery mode: No
switch-1#
说明：本地交换机的角色为Active，即具有控制权限的主交换机。
（8）查看当前交换机的VSL链路状态：
switch-1#show switch virtual link
VSL Status : DOWN
VSL Uptime : -
VSL SCP Ping : -
VSL ICC Ping : -
VSL Control Link : -
switch-1#
说明：因为还没有配置第二台交换机，所以本地交换机当前的VSL链路状态为DOWN。
（9）查看当前交换机VSS的更多信息：
switch-1#show switch virtual redundancy
My Switch Id = 1
Peer Switch Id = 2
Last switchover reason = none
Configured Redundancy Mode = sso
Operating Redundancy Mode = sso
Switch 1 Slot 5 Processor Information :
-----------------------------------------------
Current Software state = ACTIVE
Uptime in current state = 0 minutes
Image Version = Cisco IOS Software, s72033_rp Software (s72033_rp-IPBASE-VM), Version 12.2(33)SXH7, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Thu 11-Mar-10 15:13 by prod_rel_team
BOOT =
Configuration register = 0x2102
Fabric State = ACTIVE
Control Plane State = ACTIVE
Peer information is not available because
it is in 'DISABLED' state
switch-1#
说明：显示了VSS的更多信息。
（10）查看交换机当前的SSO状态：
switch-1#show redundancy states
my state = 13 -ACTIVE
peer state = 1 -DISABLED
Mode = Simplex
Unit = Primary
Unit ID = 21
Redundancy Mode (Operational) = sso
Redundancy Mode (Configured) = sso
Redundancy State = Non Redundant
Maintenance Mode = Disabled
Communications = Down Reason: Simplex mode
client count = 72
client_notification_TMR = 30000 milliseconds
keep_alive TMR = 9000 milliseconds
keep_alive count = 0
keep_alive threshold = 18
RF debug mask = 0x0
switch-1#
switch-1#
说明：本地交换机的SSO状态为Active，由于对端交换机并未配置，所以不能看到对端peer状态。
4．在核心交换机65-2上配置VSS
说明：由于目前的IOS版本中已经默认配置了SSO，所以在配置VSS时，不再需要配置SSO。
（1）查看核心交换机65-2当前的工作模式：
switch-2#show switch virtual
Switch Mode : Standalone
switch-2#
说明：核心交换机65-2当前的工作模式为Standalone，即为单机模式，而非VSS模式。
（2）将核心交换机65-2上与65-1相连的接口TenGigabitEthernet5/4和TenGigabitEthernet5/5配置为EtherChannel：
switch-2(config)#int range tenGigabitEthernet 5/4 - 5
switch-2(config-if-range)#channel-group 20 mode on
switch-2(config-if-range)#no shutdown
% Range command terminated because it failed on TenGigabitEthernet5/4
switch-2(config-if-range)#exit
00:15:51: %EC-5-STAYDOWN: Te5/4 will remain down as its port-channel Po20 is admin-down
switch-2(config)#
说明：将核心交换机65-2上与65-1相连的接口TenGigabitEthernet5/4和TenGigabitEthernet5/5配置为EtherChannel，为配置VSL作准备，请注意双方的EtherChannel号码不要配置相同。
（3）配置VSS域名与VSS主机号：
switch-2(config)#switch virtual domain 100
Domain ID 100 config will take effect only
after the exec command 'switch convert mode virtual' is issued
switch-2(config-vs-domain)#switch 2
switch-2(config-vs-domain)#switch 2 preempt
Please note that Preempt configuration will make the ACTIVE switch with lower priority to reload forcefully when preempt timer expires
switch-2(config-vs-domain)#exit
说明：配置VSS的域名为100，范围为1-255，两台交换机必须相同；配置VSS的主机号码为2，必须一台为1，另一台为2。
（4）配置VSL链路：
switch-2(config)#int port-channel 20
switch-2(config-if)#switch virtual link 2
switch-2(config-if)#no shutdown
switch-2(config-if)#exi
switch-2(config)#exi
说明：将两台交换机互连的EtherChannel配置为VSL。
（5）将交换机的工作模式改为VSS模式（确定之后，交换机将自动重启）：
switch-2#wr
Building configuration...
[OK]
switch-2#
switch-2#switch convert mode virtual
This command will convert all interface names
to naming convention "interface-type switch-number/slot/port",
save the running config to startup-config and
reload the switch.
Do you want to proceed? [yes/no]: y
Converting interface names
Building configuration...
[OK]
Saving converted configuration to bootflash: ...
Destination filename [startup-config.converted_vs-20101209-033325]?
C!傄娐覀娨*歟M礢P-3-LOGGER_FLUSHING: System pausing to ensure console debugging output.
00:18:01: %OIR-SP-6-CONSOLE: Changing console ownership to switch processor
00:18:01: %SYS-SP-3-LOGGER_FLUSHED: System was paused for 00:00:00 to ensure console debugging output.
00:18:03: %SYS-SP-3-LOGGER_FLUSHING: System pausing to ensure console debugging output.
***
*** --- SHUTDOWN NOW ---
***
00:18:03: %SYS-SP-5-RELOAD: Reload requested
00:18:03: %OIR-SP-6-CONSOLE: Changing console ownership to switch processor
00:18:03: %SYS-SP-3-LOGGER_FLUSHED: System was paused for 00:00:00 to ensure console debugging output.
System Bootstrap, Version 8.5(4)
Copyright (c) 1994-2009 by cisco Systems, Inc.
Cat6k-Sup720/SP processor with 1048576 Kbytes of main memory
Autoboot: failed, BOOT string is empty
Autoboot executing command: "boot "
Initializing ATA monitor library...
string is bootdisk:s72033-ipbase-vz.122-33.SXH7.bin
Loading image, please wait ...
Initializing ATA monitor library...
Self extracting the image... [OK]
Self decompressing the image :
###############################################################################
###############################################################################
###############################################################################
################################################################# [OK]
running startup....
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, s72033_sp Software (s72033_sp-IPBASE-VM), Version 12.2(33)SXH7, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Thu 11-Mar-10 15:46 by prod_rel_team
Image text-base: 0x01020150, data-base: 0x01021000
System detected Virtual Switch configuration...
Interface TenGigabitEthernet 2/5/4 is member of PortChannel 20
Interface TenGigabitEthernet 2/5/5 is member of PortChannel 20
00:00:22: %SYS-3-LOGGER_FLUSHING: System pausing to ensure console debugging output.
Firmware compiled 12-Jan-10 13:19 by integ Build [100]
Earl Card Index= 259
00:00:22: %PFREDUN-6-ACTIVE: Initializing as ACTIVE processor for this switch
Initializing as Virtual Switch STANDBY processor
00:00:59: %SYS-SW2_SPSTBY-3-LOGGER_FLUSHING: System pausing to ensure console debugging output.
00:00:22: %SYS-3-LOGGER_FLUSHED: System was paused for 00:00:00 to ensure console debugging output.
00:00:27: %VSL_BRINGUP-6-MODULE_UP: VSL module in slot 5 switch 2 brought up
00:00:54: %VSLP-5-VSL_UP: Ready for Role Resolution with Switch=1, MAC=8843.e1ce.4940 over 5/4
00:00:57: %VSLP-5-RRP_ROLE_RESOLVED: Role resolved as STANDBY by VSLP
00:00:57: %VSL-5-VSL_CNTRL_LINK: New VSL Control Link 5/4
00:00:57: %VSLP-5-VSL_UP: Ready for control traffic
00:00:59: %OIR-SW2_SPSTBY-6-CONSOLE: Changing console ownership to route processor
System Bootstrap, Version 12.2(17r)SX7, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2009 by cisco Systems, Inc.
Cat6k-Sup720/RP platform with 1048576 Kbytes of main memory
Download Start
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Download Completed! Booting the image.
Self decompressing the image :
###############################################################################
###############################################################################
###############################################################################
###############################################################################
###############################################################################
################################ [OK]
running startup....
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, s72033_rp Software (s72033_rp-IPBASE-VM), Version 12.2(33)SXH7, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Thu 11-Mar-10 15:13 by prod_rel_team
Image text-base: 0x01020150, data-base: 0x01021000
cisco WS-C6506-E (R7000) processor (revision 1.2) with 1040384K/8192K bytes of memory.
Processor board ID SAL1441W13F
SR71000 CPU at 600Mhz, Implementation 1284, Rev 1.2, 512KB L2 Cache
Last reset from s/w reset
1 Virtual Ethernet interface
198 Gigabit Ethernet interfaces
4 Ten Gigabit Ethernet interfaces
1917K bytes of non-volatile configuration memory.
65536K bytes of Flash internal SIMM (Sector size 512K).
Press RETURN to get started!
00:00:51: curr is 0x0
00:00:51: RP: Currently running ROMMON from S (Gold) region
00:00:52: %SPANTREE-5-EXTENDED_SYSID: Extended SysId enabled for type vlan. The Bridge IDs of all active STP instances have been updated, which might change the spanning tree topology
00:01:33: c6k_pwr_is_fantray_ok returns ok for fan_index 5
00:01:39: %SYS-5-RESTART: System restarted --
Cisco IOS Software, s72033_rp Software (s72033_rp-IPBASE-VM), Version 12.2(33)SXH7, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Thu 11-Mar-10 15:13 by prod_rel_team
switch-1-sdby>
Standby console disabled
switch-1-sdby>
Standby console disabled
switch-1-sdby>
Standby console disabled
switch-1-sdby>
Standby console disabled
说明：由于 对端交换机65-1的VSS优先级高于本交换机，所以对方交换机已经工作在了VSS的Active状态，而本地交换机65-2只能工作在Standby状 态；只有工作在Active模式的交换机才具有配置和管理双方交换机的权限，而工作在Standby状态的交换机则永远停留在用户模式（提示符 为>），enable模式是被阻塞而不能进入的。
并且需要注意，当两台交换机通过VSS合并成单台交换机之后，主机名则沿用Active交换机的主机名。
5．查看核心交换机65-1的VSS信息
（1）查看核心交换机65-1的EtherChannel状态：
switch-1#sh etherchannel summary
Flags: D - down P - bundled in port-channel
I - stand-alone s - suspended
H - Hot-standby (LACP only)
R - Layer3 S - Layer2
U - in use N - not in use, no aggregation
f - failed to allocate aggregator
M - not in use, no aggregation due to minimum links not met
m - not in use, port not aggregated due to minimum links not met
u - unsuitable for bundling
d - default port
w - waiting to be aggregated
Number of channel-groups in use: 1
Number of aggregators: 1
Group Port-channel Protocol Ports
------+-------------+-----------+-----------------------------------------------
10 Po10(RD) - Te1/5/4(w) Te1/5/5(D)
switch-1#
说明：核心交换机65-1当前的EtherChannel并未工作在正常状态，所以下面需要解决此问题。
（2）查看核心交换机65-1的配置信息：
switch-1#sh running-config
Building configuration...
Current configuration : 17253 bytes
!
upgrade fpd auto
version 12.2
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
service counters max age 5
!
hostname switch-1
!
boot-start-marker
boot-end-marker
!
logging buffered 8192 debugging
!
no aaa new-model
ip subnet-zero
!
!
!
!
switch virtual domain 100
switch mode virtual
switch 1 priority 200
switch 1 preempt
!
call-home
alert-group configuration
alert-group diagnostic
alert-group environment
alert-group inventory
alert-group syslog
profile "CiscoTAC-1"
no active
no destination transport-method http
destination transport-method email
destination address email callhome@cisco.com
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
subscribe-to-alert-group diagnostic severity minor
subscribe-to-alert-group environment severity minor
subscribe-to-alert-group syslog severity major pattern ".*"
subscribe-to-alert-group configuration periodic monthly 17 14:11
subscribe-to-alert-group inventory periodic monthly 17 13:56
mls netflow interface
no mls flow ip
no mls flow ipv6
mls cef error action reset
diagnostic cns publish cisco.cns.device.diag_results
diagnostic cns subscribe cisco.cns.device.diag_commands
!
redundancy
keepalive-enable
mode sso
main-cpu
auto-sync running-config
spanning-tree mode pvst
spanning-tree extend system-id
!
!
!
vlan internal allocation policy ascending
vlan access-log ratelimit 2000
!
!
interface Port-channel10
no switchport
no ip address
switch virtual link 1
mls qos trust cos
no mls qos channel-consistency
!
interface GigabitEthernet1/1/1
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/1/2
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/1/3
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/1/4
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/1/5
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/1/6
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/1/7
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/1/8
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/1/9
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/1/10
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/1/11
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/1/12
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/1/13
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/1/14
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/1/15
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/1/16
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/1/17
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/1/18
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/1/19
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/1/20
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/1/21
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/1/22
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/1/23
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/1/24
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/1/25
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/1/26
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/1/27
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/1/28
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/1/29
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/1/30
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/1/31
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/1/32
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/1/33
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/1/34
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/1/35
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/1/36
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/1/37
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/1/38
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/1/39
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/1/40
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/1/41
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/1/42
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/1/43
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/1/44
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/1/45
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/1/46
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/1/47
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/1/48
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/2/1
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/2/2
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/2/3
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/2/4
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/2/5
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/2/6
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/2/7
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/2/8
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/2/9
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/2/10
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/2/11
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/2/12
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/2/13
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/2/14
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/2/15
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/2/16
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/2/17
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/2/18
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/2/19
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/2/20
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/2/21
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/2/22
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/2/23
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/2/24
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/2/25
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/2/26
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/2/27
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/2/28
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/2/29
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/2/30
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/2/31
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/2/32
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/2/33
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/2/34
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/2/35
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/2/36
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/2/37
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/2/38
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/2/39
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/2/40
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/2/41
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/2/42
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/2/43
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/2/44
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/2/45
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/2/46
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/2/47
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/2/48
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/5/1
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/5/2
no switchport
no ip address
shutdown
!
interface GigabitEthernet1/5/3
no switchport
no ip address
shutdown
!
interface TenGigabitEthernet1/5/4
no switchport
no ip address
mls qos trust cos
channel-group 10 mode on
!
interface TenGigabitEthernet1/5/5
no switchport
no ip address
mls qos trust cos
channel-group 10 mode on
!
interface GigabitEthernet2/1/1
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/1/2
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/1/3
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/1/4
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/1/5
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/1/6
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/1/7
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/1/8
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/1/9
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/1/10
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/1/11
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/1/12
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/1/13
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/1/14
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/1/15
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/1/16
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/1/17
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/1/18
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/1/19
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/1/20
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/1/21
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/1/22
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/1/23
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/1/24
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/1/25
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/1/26
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/1/27
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/1/28
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/1/29
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/1/30
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/1/31
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/1/32
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/1/33
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/1/34
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/1/35
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/1/36
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/1/37
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/1/38
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/1/39
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/1/40
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/1/41
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/1/42
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/1/43
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/1/44
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/1/45
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/1/46
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/1/47
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/1/48
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/2/1
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/2/2
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/2/3
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/2/4
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/2/5
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/2/6
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/2/7
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/2/8
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/2/9
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/2/10
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/2/11
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/2/12
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/2/13
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/2/14
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/2/15
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/2/16
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/2/17
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/2/18
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/2/19
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/2/20
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/2/21
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/2/22
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/2/23
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/2/24
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/2/25
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/2/26
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/2/27
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/2/28
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/2/29
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/2/30
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/2/31
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/2/32
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/2/33
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/2/34
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/2/35
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/2/36
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/2/37
no switchport
no ip address
shutdown
!
interface GigabitEthernet2/2/38
no switchport
no ip address
shutdown
!
