Boot Address 0xbe000000
Initializing Arena.
Initializing Devices.
Parallel flash device: name AM29LV320MT|S29GL128-A, id 0x2201, size 16384KB
Flash Layout: Boot[0,0xbe000000] Kern[1,0xbe020000]
AuxFS[93,0xbeba0000] Misc[125,0xbefa0000] PSI[127,0xbefe0000]
Flash RootFS Partition Length: 12058624
CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz
CPU running TP0
Total memory: 33554432 bytes (32MB)
Total memory used by CFE: 0x80401000 - 0x80529860 (1214560)
Initialized Data: 0x8041E740 - 0x80421060 (10528)
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Boot image (0=latest, 1=previous) : 0
Board Id (0-8) : 96358VW2
Number of MAC Addresses (1-32) : 11
Base MAC Address : 00:1f:a3:b2:fa:df
PSI Size (1-64) KBytes : 24
Flash Block Size (1-128) in KBytes: 128
Auxillary File System Size Percent: 25
Main Thread Number [0|1] : 0
udp_send finished
No answer .auto boot ...
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
Booting from latest image (0xbe020000) ...
Code Address: 0x80010000, Entry Address: 0x8026c018
Decompression OK!
Entry at 0x8026c018
Closing network.
Starting program at 0x8026c018
Linux version 2.6.8.1 () (gcc version 3.4.2) #1 Tue Dec 2 17:29:24 CST 2008
Parallel flash device: name AM29LV320MT|S29GL128-A, id 0x2201, size 16384KB
fInfo.flash_rootfs_available_length = 16252928
96358VW2 prom init
CPU revision is: 0002a010
Determined physical RAM map:
memory: 01fa0000 @ 00000000 (usable)
On node 0 totalpages: 8096
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 4000 pages, LIFO batch:1
HighMem zone: 0 pages, LIFO batch:1
Built 1 zonelists
Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
brcm mips: enabling icache and dcache...
Primary instruction cache 32kB, physically tagged, 2-way, linesize 16 bytes.
Primary data cache 16kB 2-way, linesize 16 bytes.
PID hash table entries: 128 (order 7: 1024 bytes)
Using 150.000 MHz high precision timer.
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 29344k/32384k available (1908k kernel code, 2996k reserved, 504k data, 76k init, 0k highmem)
Calibrating delay loop... 299.00 BogoMIPS
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Checking for 'wait' instruction... unavailable.
NET: Registered protocol family 16
Total Flash size: 16384K with 128 sectors
Computing partition layout for flash of size[16777216] sectors[128]
Flash split 25% into RootFS+Kernel[12058624] : AuxFS[4194304]
Partition ROOTFS_KRN [0xbe020000, 12058624] Blks[ 92: 1 .. 92]
SubPartition Image 1 [0xbe020000, 6029312] Blks[ 46: 1 .. 46]
SubPartition Image 2 [0xbe5e0000, 6029312] Blks[ 46: 47 .. 92]
Blk# BlkOff Blks BlkSize AvailSize MemStart MemLen Partition Name
0 1408 1 131072 131072 0xbe000580 1024 BOOTLOADER
1 0 92 131072 12058624 0xbe020000 12058624 ROOTFS_KRN
93 0 32 131072 4194304 0xbeba0000 4194304 JFFS_AUXFS
125 0 1 131072 131072 0xbefa0000 131072 LOG_SCRPAD
126 106496 1 131072 131072 0xbefda000 24576 TW_PERSISTMEM
127 106496 1 131072 131072 0xbeffa000 24576 PERSISTMEM
Can't analyze prologue code at 801eb814
SCSI subsystem initialized
usbcore: registered new driver hub
JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.
Initializing Cryptographic API
PPP generic driver version 2.4.2
NET: Registered protocol family 24
Using noop io scheduler
bcm963xx_mtd driver v2.0
File system address: 0xbe020100
Registered device mtd[BCM63XX RootFS] dev[0] Flash[0xbe020100,4558848]
Registered device mtd[BCM63XX AuxFS] dev[1] Flash[0xbeba0000,4194304]
PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
ehci_hcd 0000:00:0a.0: EHCI Host Controller
PCI: Setting latency timer of device 0000:00:0a.0 to 64
ehci_hcd 0000:00:0a.0: irq 18, pci mem c0050300
ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1
PCI: cache line size of 32 is not supported by device 0000:00:0a.0
ehci_hcd 0000:00:0a.0: USB f.f enabled, EHCI 1.00, driver 2004-May-10
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
ohci_hcd 0000:00:09.0: OHCI Host Controller
PCI: Setting latency timer of device 0000:00:09.0 to 64
ohci_hcd 0000:00:09.0: irq 13, pci mem c0052400
ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
brcmboard: brcm_board_init entry
SES: Button Interrupt 0x3 is enabled
WIFI: Button Interrupt 0x0 is enabled
WIFI: map_external_irq begin
SES: LED GPIO 0x8018 is enabled
initLed: led[0]: mask=0x400000, state=0
initLed: led[1]: mask=0x0000, state=0
initLed: led[2]: mask=0x1000000, state=0
initLed: led[3]: mask=0x0001, state=0
initLed: led[4]: mask=0x0004, state=0
initLed: led[5]: mask=0x0010, state=0
initLed: led[6]: mask=0x0002, state=0
Serial: BCM63XX driver $Revision: 3.00 $
ttyS0 at MMIO 0xfffe0100 (irq = 10) is a BCM63XX
ttyS1 at MMIO 0xfffe0120 (irq = 11) is a BCM63XX
u32 classifier
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
Ebtables v2.0 registered
NET: Registered protocol family 8
NET: Registered protocol family 20
802.1Q VLAN Support v1.8 Ben Greear <>
All bugs added by David S. Miller <>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 76k freed
init started: BusyBox v1.00 (2008.12.02-09:34+0000) multi-call binary
Algorithmics/MIPS FPU Emulator v1.5
BusyBox v1.00 (2008.12.02-09:34+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.
Loading drivers and kernel modules...
atmapi: module license 'Proprietary' taints kernel.
adsl: adsl_init entry
blaadd: blaa_detect entry
fuse init (API version 7.8)
fuse distribution version: 2.7.3
Broadcom BCMPROCFS v1.0 initialized
Broadcom BCM6358A1 Ethernet Network Device v0.3 Dec 2 2008 17:27:51
Config Ethernet Switch Through MDIO Pseudo PHY Interface
dgasp: kerSysRegisterDyingGaspHandler: eth0 registered
eth0: MAC Address: 00:1F:A3:B2:FA:DF
PCI: Setting latency timer of device 0000:00:01.0 to 64
PCI: Enabling device 0000:00:01.0 (0004 -> 0006)
wl: srom not detected, using main memory mapped srom info (wombo board)
wl0: wlc_attach: use mac addr from the system pool by id: 0x776c0000
wl0: MAC Address: 00:1F:A3:B2:FA:E0
wl0: Broadcom BCM4318 802.11 Wireless Controller 4.150.10.15.cpe2.2
dgasp: kerSysRegisterDyingGaspHandler: wl0 registered
usbback enable:0
xmlEndCTCfgObj(calling cfm to get appName SystemInfo, objName ctCfg
xmlEndCTCfgObj(calling cfm to get appName SystemInfo, objName ctCfg
xmlEndCTCfgObj(calling cfm to get appName SystemInfo, objName ctCfg
BcmAdsl_Initialize=0xC00BA408, g_pFnNotifyCallback=0xC00D33C4
AnnexCParam=0x7FFF7EA8 AnnexAParam=0x00003987 adsl2=0x00000000
pSdramPHY=0xA1FFFFF8, 0x34D5 0xDEADBEEF
AdslCoreHwReset: AdslOemDataAddr = 0xA1FFBA64
AnnexCParam=0x7FFF7EA8 AnnexAParam=0x00003987 adsl2=0x00000000
dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered
ATM proc init !!!
get qos queue policy type error
Enable = 1
enter QosPriorityQueueTbl::removeAllTCRules
waninfo 8021d= -1, vlanid= -1 muxVlanId = -1
remove tc rule of the interface nas_0_0_32
Cannot find device "nas_0_0_32"
waninfo 8021d= -1, vlanid= -1 muxVlanId = -1
remove tc rule of the interface nas_0_0_33
Cannot find device "nas_0_0_33"
waninfo 8021d= -1, vlanid= -1 muxVlanId = -1
remove tc rule of the interface nas_0_0_35
Cannot find device "nas_0_0_35"
waninfo 8021d= -1, vlanid= -1 muxVlanId = -1
remove tc rule of the interface nas_0_0_100
Cannot find device "nas_0_0_100"
waninfo 8021d= -1, vlanid= -1 muxVlanId = -1
remove tc rule of the interface nas_0_8_32
Cannot find device "nas_0_8_32"
waninfo 8021d= -1, vlanid= -1 muxVlanId = -1
remove tc rule of the interface nas_0_8_35
Cannot find device "nas_0_8_35"
waninfo 8021d= -1, vlanid= -1 muxVlanId = -1
remove tc rule of the interface nas_0_8_81
Cannot find device "nas_0_8_81"
waninfo 8021d= -1, vlanid= -1 muxVlanId = -1
remove tc rule of the interface nas_0_1_33
Cannot find device "nas_0_1_33"
==> Bcm963xx Software Version: GWH-11_V1.1 <==
device eth0 entered promiscuous mode
br0: port 1(eth0) entering learning state
br0: topology change detected, propagating
br0: port 1(eth0) entering forwarding state
buffer=2.6.8.1
-----insmod=insmod /lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/ip_conntrack_devicectl.ko ip_begin=3232235777 ip_end=3232236030 mode=0 maxTotalNumber=250 maxComputerNumber=1 maxStbNumber=0 maxCameraNumber=1 computerStatus=0 stbStatus=0 cameraStatus=0
ip_conntrack_devicectl: load success
ses_led_off_ex I want
ctlstate = 0x0
recv action = 0
recv event = 0x0
blinktype=0, event=0, status=0
Setting SSID "ChinAdsl.Nets"
Setting SSID "Guest"
Setting SSID "Guest1"
Setting SSID "Guest2"
Setting country code using abbreviation: "ALL"
channel 1 selected
device wl0 entered promiscuous mode
br0: port 2(wl0) entering learning state
br0: topology change detected, propagating
br0: port 2(wl0) entering forwarding state
device wl0.1 entered promiscuous mode
br0: port 3(wl0.1) entering learning state
br0: topology change detected, propagating
br0: port 3(wl0.1) entering forwarding state
device wl0.2 entered promiscuous mode
br0: port 4(wl0.2) entering learning state
br0: topology change detected, propagating
br0: port 4(wl0.2) entering forwarding state
device wl0.3 entered promiscuous mode
br0: port 5(wl0.3) entering learning state
br0: topology change detected, propagating
br0: port 5(wl0.3) entering forwarding state
br0: port 3(wl0.1) entering disabled state
br0: port 4(wl0.2) entering disabled state
br0: port 5(wl0.3) entering disabled state
BcmRfc2684_init interface is not up nas_0_0_32!
pvc2684ctl -a -v 0.0.32 &
pvc2684d: Interface "nas_0_0_32" created sucessfully
pvc2684d: Communicating over ATM 0.0.32, encapsulation: LLC
psiTraffictl = 716019160
HTB init, kernel part version 3.17
device nas_0_0_32 entered promiscuous mode
br0: port 6(nas_0_0_32) entering learning state
br0: topology change detected, propagating
br0: port 6(nas_0_0_32) entering forwarding state
BcmRfc2684_init interface is not up nas_0_0_33!
pvc2684ctl -a -v 0.0.33 &
pvc2684d: Interface "nas_0_0_33" created sucessfully
pvc2684d: Communicating over ATM 0.0.33, encapsulation: LLC
psiTraffictl = 716019160
HTB init, kernel part version 3.17
device nas_0_0_33 entered promiscuous mode
br0: port 7(nas_0_0_33) entering learning state
br0: topology change detected, propagating
br0: port 7(nas_0_0_33) entering forwarding state
BcmRfc2684_init interface is not up nas_0_0_35!
pvc2684ctl -a -v 0.0.35 &
pvc2684d: Interface "nas_0_0_35" created sucessfully
pvc2684d: Communicating over ATM 0.0.35, encapsulation: LLC
psiTraffictl = 716019160
HTB init, kernel part version 3.17
device nas_0_0_35 entered promiscuous mode
br0: port 8(nas_0_0_35) entering learning state
br0: topology change detected, propagating
br0: port 8(nas_0_0_35) entering forwarding state
BcmRfc2684_init interface is not up nas_0_0_100!
pvc2684ctl -a -v 0.0.100 &
pvc2684d: Interface "nas_0_0_100" created sucessfully
pvc2684d: Communicating over ATM 0.0.100, encapsulation: LLC
psiTraffictl = 716019160
HTB init, kernel part version 3.17
device nas_0_0_100 entered promiscuous mode
br0: port 9(nas_0_0_100) entering learning state
br0: topology change detected, propagating
br0: port 9(nas_0_0_100) entering forwarding state
BcmRfc2684_init interface is not up nas_0_8_32!
pvc2684ctl -a -v 0.8.32 &
pvc2684d: Interface "nas_0_8_32" created sucessfully
pvc2684d: Communicating over ATM 0.8.32, encapsulation: LLC
psiTraffictl = 716019160
HTB init, kernel part version 3.17
device nas_0_8_32 entered promiscuous mode
br0: port 10(nas_0_8_32) entering learning state
br0: topology change detected, propagating
br0: port 10(nas_0_8_32) entering forwarding state
BcmRfc2684_init interface is not up nas_0_8_35!
pvc2684ctl -a -v 0.8.35 &
pvc2684d: Interface "nas_0_8_35" created sucessfully
pvc2684d: Communicating over ATM 0.8.35, encapsulation: LLC
psiTraffictl = 716019160
HTB init, kernel part version 3.17
device nas_0_8_35 entered promiscuous mode
br0: port 11(nas_0_8_35) entering learning state
br0: topology change detected, propagating
br0: port 11(nas_0_8_35) entering forwarding state
BcmRfc2684_init interface is not up nas_0_8_81!
pvc2684ctl -a -v 0.8.81 &
pvc2684d: Interface "nas_0_8_81" created sucessfully
pvc2684d: Communicating over ATM 0.8.81, encapsulation: LLC
psiTraffictl = 716019160
HTB init, kernel part version 3.17
device nas_0_8_81 entered promiscuous mode
br0: port 12(nas_0_8_81) entering learning state
br0: topology change detected, propagating
br0: port 12(nas_0_8_81) entering forwarding state
BcmRfc2684_init interface is not up nas_0_1_33!
pvc2684ctl -a -v 0.1.33 &
pvc2684d: Interface "nas_0_1_33" created sucessfully
pvc2684d: Communicating over ATM 0.1.33, encapsulation: LLC
psiTraffictl = 716019160
HTB init, kernel part version 3.17
device nas_0_1_33 entered promiscuous mode
br0: port 13(nas_0_1_33) entering learning state
br0: topology change detected, propagating
br0: port 13(nas_0_1_33) entering forwarding state
device eth0 left promiscuous mode
br0: port 1(eth0) entering disabled state
device wl0 left promiscuous mode
br0: port 2(wl0) entering disabled state
device wl0.1 left promiscuous mode
br0: port 3(wl0.1) entering disabled state
device wl0.2 left promiscuous mode
br0: port 4(wl0.2) entering disabled state
device wl0.3 left promiscuous mode
br0: port 5(wl0.3) entering disabled state
device nas_0_0_32 left promiscuous mode
br0: port 6(nas_0_0_32) entering disabled state
device nas_0_0_33 left promiscuous mode
br0: port 7(nas_0_0_33) entering disabled state
device nas_0_0_35 left promiscuous mode
br0: port 8(nas_0_0_35) entering disabled state
device nas_0_0_100 left promiscuous mode
br0: port 9(nas_0_0_100) entering disabled state
device nas_0_8_32 left promiscuous mode
br0: port 10(nas_0_8_32) entering disabled state
device nas_0_8_35 left promiscuous mode
br0: port 11(nas_0_8_35) entering disabled state
device nas_0_8_81 left promiscuous mode
br0: port 12(nas_0_8_81) entering disabled state
device nas_0_1_33 left promiscuous mode
br0: port 13(nas_0_1_33) entering disabled state
device eth0 entered promiscuous mode
br0: port 1(eth0) entering learning state
br0: topology change detected, propagating
br0: port 1(eth0) entering forwarding state
device wl0 entered promiscuous mode
br0: port 2(wl0) entering learning state
br0: topology change detected, propagating
br0: port 2(wl0) entering forwarding state
device wl0.1 entered promiscuous mode
br0: port 3(wl0.1) entering learning state
br0: topology change detected, propagating
br0: port 3(wl0.1) entering forwarding state
device wl0.2 entered promiscuous mode
br0: port 4(wl0.2) entering learning state
br0: topology change detected, propagating
br0: port 4(wl0.2) entering forwarding state
device wl0.3 entered promiscuous mode
br0: port 5(wl0.3) entering learning state
br0: topology change detected, propagating
br0: port 5(wl0.3) entering forwarding state
device nas_0_0_32 entered promiscuous mode
br0: port 6(nas_0_0_32) entering learning state
br0: topology change detected, propagating
br0: port 6(nas_0_0_32) entering forwarding state
device nas_0_0_33 entered promiscuous mode
br0: port 7(nas_0_0_33) entering learning state
br0: topology change detected, propagating
br0: port 7(nas_0_0_33) entering forwarding state
device nas_0_0_35 entered promiscuous mode
br0: port 8(nas_0_0_35) entering learning state
br0: topology change detected, propagating
br0: port 8(nas_0_0_35) entering forwarding state
device nas_0_0_100 entered promiscuous mode
br0: port 9(nas_0_0_100) entering learning state
br0: topology change detected, propagating
br0: port 9(nas_0_0_100) entering forwarding state
device nas_0_8_32 entered promiscuous mode
br0: port 10(nas_0_8_32) entering learning state
br0: topology change detected, propagating
br0: port 10(nas_0_8_32) entering forwarding state
device nas_0_8_35 entered promiscuous mode
br0: port 11(nas_0_8_35) entering learning state
br0: topology change detected, propagating
br0: port 11(nas_0_8_35) entering forwarding state
device nas_0_8_81 entered promiscuous mode
br0: port 12(nas_0_8_81) entering learning state
br0: topology change detected, propagating
br0: port 12(nas_0_8_81) entering forwarding state
device nas_0_1_33 entered promiscuous mode
br0: port 13(nas_0_1_33) entering learning state
br0: topology change detected, propagating
br0: port 13(nas_0_1_33) entering forwarding state
sntp: host not found
ipt_time: Unknown symbol ipt_register_match
ipt_time: Unknown symbol ipt_unregister_match
insmod: cannot insert `/lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/ipt_time.ko': Success (2): Success
blaa_dd: port mirroring config.
blaa_dd: port mirroring config.
SIOCSIFADDR: No such device
SIOCSIFNETMASK: No such device
SIOCSIFBRDADDR: No such device
br0: port 1(eth0) entering disabled state
CONSOLED launched
Login:
